Pro 1 IAQ True Comfort T715 User manual

Caution:
Equipment damage hazard
Do not operate the cooling
system if the outdoor
temperature is below 50°
F
(10
°
C) to prevent possible
compressor damage.
}
Una version en espanol de este
manual se puede descargar en la
pagina web de la compania.

)
OPERATING MANUAL
PRO
T715
Prot Technologies, Inc.
1111 S. Glenstone Ave., Suite 2-100
Springfield, MO 65804
Toll
-
Free:
888-776-1427
Web:
www.proliaq.com
Hours of Operation:
M-F 9AM - 6PM Eastern
Table of Contents

Page
Thermostat Quick Reference

2
Thermostat Operation

3
Programming Thermostat

4-5
Warranty Registration

6
1
-
Rev. 1315

4)
® U.S. Registered Trademark. Patents pending.
Copyright © 2013. All rights reserved.

Getting to know your thermostat
COOL OFF HEAT
Displays the user
selectable setpoint
temperature.
Days of the
week and time
Set Time
Run Sched Temperature Hold
„imp, ,,
Set Sched 0 I l r ,(
**-----
Hold 
Am ow  -ti
Prey Step
Sun Mon Tub Wed Thu F
N
e xt  i n r L i n el s e t At
Next Step
1/0#01 -00 nri
AM PM u
Indicates
the
current room
temperature.
C r
F  ''')
ti4iii toll *
+I
LEAVE RETURNIU
Button
options
Important:
The low battery indicator is displayed when
the AAbattery power is low. If the user fails to
replace the battery within
21 days, the screen
will only show the low battery indicator but
maintain all functionality. If the user fails to
replace the batteries after an additional
21
days (days 22-42 since first low battery"
display) the set points will change to
55°F(Heating) and 85°F(Cooling). If the user
adjusts these setpoints away from these it will
hold for 4 hours then return to either 55°F or
85°F. After day 42 the batteries must be
replaced immediately to avoid freezing or
overheating because the thermostat will shut
the unit off until the battery is changed.
Use the finger bevel on
the lower portion of the
side of the thermostat to
open the easy access
battery door.
Insert 2 AA Alkaline
batteries (included).
High quality alkaline
batteries are
recommended.
Refer to your Operating Manual
for programming and operation
instruction. A copy can be
downloaded at www.proliaq.com
Replace AA Batteries when low battery indicator shows in display.
Simple operating instructions are
found on the back of the battery door.
Select Heat, Off, or Cool as
needed. Select Fan On for
continuous operation or Fan
Auto to cycle fan with system.
THERMOSTAT QUICK REFERENCE
Programmable Time Period Icons:
This thermostat has 4 programmable
time periods per day.
Hold is displayed when
thermostat program is
permanently overridden.
*
*
COOL HEAT FAN
System operation
indicators: The COOL,
HEAT or FAN icon will
display when the COOL,
HEAT or FAN is on.
NOTE: The compressor delay
feature is active if these icons
are flashing. The compressor
will not turn on until the 5
minute delay has elapsed.
Low Battery Indicator:
Replace batteries when
indicator is shown.
+1 will appear in the
display when the second
stage of HEAT
or the second
stage of COOL
is active.
0 LCD (Right)
0 Glow in the Dark Light Button
Fan Switch
System Switch
Easy Change Battery Door
Setpoint Buttons
User Buttons
Battery door information

lc)
FAN
ON AUTO
O
Mon
I 
r1 :1 Set At
I LI • LI _I
"wo g g
AM
I  I
Temperature
1 ,J
SYSTEM ,
COOL OFF HEAT
Caution:
When the battery icon
appears replace your AA
batteries immediately. Failure
to do so may result in your
heating & cooling system
becoming inoperable.
THERMOSTAT OPERATION
Easy to use controls
0 LCD Display:
See page 2 for details about this display
read out and icons.
0 Glow in the Dark Light Button:
The glow in the dark light button will
self illuminate for several hours after
exposure to ambient light. This button
turns on the display light when pressed.
® Fan Switch:
Select
ON or AUTO. ON
will run
the fan continuously.
AUTO will cycle
the fan on only when the heating or
cooling system is on.
® System Switch:
Selects the operation mode of your
HVAC system. Selecting HEAT
turns
on the heat mode. Selecting
COOL
turns on the air conditioning mode.
Selecting OFF turns both heating
and cooling off.
0 Temperature Setpoint Buttons:
Press the + or - buttons to select the
desired room temperature.
0
User Buttons:
Use these buttons to set up your
programming options. Refer to the
next page for instructions.
O

PROGRAMMING THE THERMOSTAT
Set Time
Follow the steps below to set the current time:
1. Press
MENU
2. Press
SET TIME
3.
Day of the week will be flashing.
Use the

or 
key to select the current
day of the week.
4. Press
NEXT STEP
5.
The current hour is flashing.
Use the 
or 
key to select the current
hour. When using 12-hour time, make sure the
correct a.m. or p.m. choice is selected.
6. Press NEXT STEP
7.
Minutes are now flashing.
Use the
 or 
key to select
current minutes.
8. Press
DONE
when completed
Important:
You will see a
TECH SET
option after the MENU key
is pressed.
This TECH SET key is for
installer configuration and
should NOT be changed
unless you consult your
Professional Heating and
Air Conditioning Technician.
Set Program Schedule
To customize your program schedule, follow these steps
Weekday:
1. Select HEAT or COOL
from the system switch.
Note: You have to program heat and cool each
separately.
2. Press MENU
3. Press SET SCHED.
Note: Monday-Friday is displayed
and the WAKE
icon is shown. You are now program-
ming the wake time period for the weekday setting.
4.
Time is flashing. Use the  or 
key to make
your time selection for the weekday
WAKE time period.
5. Press NEXT STEP
6.
The setpoint temperature is flashing. Use the

or
key to make your setpoint selection for the weekday
wake period.
7. Press NEXT STEP
8. Repeat steps 4 through 7 for weekday
LEAVE time
period, for weekday RETURN
time period, and for
weekday SLEEP time period.
Saturday:
9. Repeat steps 4 through 7 for
Saturday WAKE time period,
for Saturday LEAVE time
period, for Saturday RETURN
time period, and for Saturday
SLEEP time period.
Sunday:
10. Repeat steps 4 through 7 for
Sunday WAKE time period,
for Sunday LEAVE time
period, for Sunday RETURN
time period, and for Sunday
SLEEP time period.

Mon
I In .

Set At
I
LI- LI 1 n
AM

I
Temperature
SYSTEM
COOL OFF HEAT
FAN
ON AUTO
PROGRAMMING THE THERMOSTAT
Filter Change Reminder
If your installing contractor has configured
the thermostat to remind you when the air
filter needs changed, you will see
FILT
in the
display when your air filter needs changed.
FILT
will be shown in the display after your
system has run long enough to require an air
filter change.
Resetting the filter change reminder: When
FILT
reminder is displayed, you should
change your air filter and reset the reminder
by holding down the second button from the
top left side of the thermostat for 3 seconds.
Hold down for 3 seconds,
to reset filter reminder.
Temporary and Permanent Hold Feature
Temporary hold: The thermostat will display
HOLD
and
RUN SCHEDon the left
of your
screen when you press the

or

key.
If you do nothing, the temperature will remain
at this setpoint temporarily until the next
program period begins. Your program
setpoint will then replace your temporary
setpoint.
Permanent hold:
If
you press
HOLD,
you will
see
HOLD
appear below the setpoint tem-
perature in the display. The thermostat will
now permanently stay
at this
setpoint and can
be adjusted using the

or

keys.
To return to program: Press
RUN SCHED
to
exit either temporary or permanent hold.
Understanding Thermostat Staging
Your thermostat will control two stages of
heating and cooling. The thermostat will try to
maintain your comfort setting using the first
stage for energy efficiency. The second stage
of heating or cooling will only be used if your
thermostat cannot maintain your comfort
setting using only one stage. When the second
stage is used you will see
+1
in the display.

WARRANTY INFORMATION
[ Warranty Registration:
Your new thermostat has a 5 year limited warranty. You must register your warranty
within 60 days of installation. You can register your new thermostat in 2 ways.
CI
Go to the company website, select warranty registration and fill out a short registration form.
- or -
®
Complete the form below and mail it to the address shown.
Warranty Registration:
Name: 
Thermostat Model:
Address:

Date Installed:
City:
State:
Zip:
Complete form and mail to:
Thermostat Warranty Registration
1111 S. Glenstone
Suite 2-100
Springfield, MO 65804