Pro-Lift F1500A User manual

1
OWNER’S MANUAL
WORKING LOAD LIMIT 1500KG
• Safety Instructions
• Operation Procedures
• Maintenance Procedures
READ RULES FOR SAFE OPERATION
AND INSTRUCTIONS CAREFULLY
Model: F1500A
THIS JACK CONFORMS TO MANDATORY
STANDARD AS 2615:2016
Shinn Fu (Australia) PTY. LTD.
15 Viewtech Place, Rowville, Victoria 3178, Australia
FLOOR JACK
WARNING: THE JACK MUST BE USED ONLY ON HARD LEVEL
SURFACES AND BE FREE TO ROLL DURING LIFTING AND LOW-
ERING. DO NOT GET UNDER A VEHICLE THAT IS SUPPORTED
BY A TROLLEY JACK - USE THIS HYDRAULIC TROLLEY JACK
WITH SUITABLY RATED VEHICLE SUPPORT STANDS.

2
SAFETY INSTRUCTIONS
INSPECTIONS
This hydraulic trolley jack is designed to be used with a 48mm diameter head cap.
1. BEFORE EACH USE
Visual inspection should be made before each use of the trolley jack for abnormal
conditions such as cracked welds, leaks and damaged, loose, or missing parts.
2. AFTER EACH USE
Trolley jack should be inspected immediately if the lift is believed to have been
subjected to an abnormal load or shock. It is recommended that inspection be made
by manufacturer’s or supplier’s authorised repair facility.
3. ANNUAL INSPECTION
Annual inspection of the trolley jack is recommended and is recommended to be
made by the manufacturer’s or supplier’s authorised repair facility to ensure that
your trolley jack is in optimum condition.
RECOMMENDATION FOR SAFE USAGE OF THE JACK
1. Consult the vehicle manufacturer’s manual prior to the lifting of the vehicle.
2. Conduct a pre-operational check of the equipment.
3. Use the hydraulic trolley jack for lifting and lowering only; the raised vehicle should
be supported on suitably rated vehicle support stands.
4. Use the hydraulic trolley jack on a hard level surface and ensure it is free to roll
during lifting and lowering.
5. No person should remain in a vehicle that is being lifted.
6. Chock the unlifted wheels of the vehicle.
7. Centrally locate the load on the head cap.
8. Support the vehicle on suitably rated vehicle support stands and remove the hydraulic
trolley jack prior to commencement of work on the vehicle.
9. No person should get bodily under a vehicle that is supported only by a hydraulic
trolley jack.
10. Make sure that lift point is stable and properly centered on jack saddle.
11. Vehicle should be clear of all passengers. Transmission should be in gear (or park
for automation transmission) and the emergency brake should be engaged.
12. Familiarize yourself thoroughly with this owner manual before operation to prevent
damage to jack and property, or personal injury.
Modications: Modications must not be carried out or accessories added.

SAFETY INSTRUCTIONS
CAUTION BEFORE USE
Due to shipment and/or handling air can be trapped in the hydraulic system, which can
interfere with the jacks lifting. To release air from the hydraulic system:
• Open release valve by turning the jack handle counterclockwise.
• Remove the oil ller plug from the cylinder.
• Rapidly pump jack handle through several full strokes.
• Replace the oil ller plug into the cylinder.
WARNING
DEATH OR
INJURY FROM
INCORRECT USE
USE TWO
SUPPORT
STANDS
FLAT HARD
LEVEL GROUND
FREE TO ROLL
DURING LIFTING
AND LOWERING
REFER TO VEHICLE MANUFACTURER’S
MANUAL FOR INSTRUCTIONS
3

4
OPERATION PROCEDURES
Before using
1. Remove cover plate (friction t, easily
removes) and open Oil Filler Plug to
allow air to be vented.
2. Open Release Valve with the handle.
Turn it counterclockwise.
3. Pump handle rapidly several times.
4. Close oil ller plug, then replace cover
plate.
5. No person should remain in the vehicle
that is being jacked.
Raising the jack
1. Place car in park, apply emergency
brake and chocked wheel in “straight
ahead” position.
2.Close Release Valve TIGHTLY (by
applying handle turning clockwise).
3. Position jack under load so that saddle
will contact load rmly and is centered
so it cannot slip. Avoid off-centered load
on the saddle.
4. Operate jack handle until saddle almost
approaches to contact with load. Once
again check to see that the saddle is
correctly positioned.
5. Raise load to desired height. Transfer
the load to Jack Stands immediately.
Lowering the jack
Open Release Valve VERY SLOWLY (by
applying handle turning counterclockwise)
and never more than 1/2 turns. When
Release Valve is opened, saddle will lower
easily due to spring tension on the Lift Arm
Assembly.
Moving the jack
Place handle in Handle Sleeve. DO NOT
move the jack when handle is on the
Release Valve as this may cause damage
to the pump unit of the jack. DO NOT move
the jack when it is under load.
CAUTION
Keep clear from the vehicle when
lowering the jack.
PARTS KEY
1. Oil Filler Plug
(Not shown, under Cover Plate)
2. Castor
3. Base
4. Release Valve
5. Pump Cylinder
6. Pump Piston
7. Handle Sleeve
8. Cover Plate
9. Lifting Arm
10. Saddle
11. Link Rod
12. Front Wheel
13. Frame
14. Middle Spindle
15. Reservoir
(Not shown, under Cover Plate)
16. Handle
17. Carrying Handle
10
1
16
7
6
4
3
2
13
17
11
12
14
9
815
5

5
MAINTENANCE PROCEDURES
MAINTAINING OIL LEVEL
Important Note:
When adding or replacing oil, always
use a good grade Hydraulic Jack Oil (or
transmission oil, turbine oil etc.). Avoid
mixing types of oil. DO NOT use Brake
Fluid, Alcohol, Glycerine, Detergent, Motor
Oil or Dirty Oil. Improper uid can cause
serious internal damage to Jack.
ADDING OIL:
With saddle fully lowered & jack on level
ground, remove cover plate then open
Oil Filler Plug. Oil level should be approx.
12mm below valve hole. If low, add oil
as needed then close Oil Filler Plug and
replace cover plate.
REPLACING OIL:
For better performance and longevity,
replace oil supply once a year. To drain
oil, remove cover plate, open Oil Filler
Plug and loosen the Release Valve by
applying handle turning counterclockwise.
BE VERY CAREFUL not to permit dirt or
foreign matter to get into the system. Close
Oil Filler Plug and replace cover plate.
SPECIFICATIONS
Working Load Limit : ......................................................................................... 1500Kg
Jack Dimension : ...............................................................445mm x 202mm x 135mm
Height Lowered : ...............................................................................................135mm
Height Raised : ..................................................................................................330mm
Oil Capacity : ...................................................................................................70+/-5cc
Net Weight : .........................................................................................8.4Kg. (approx.)
202mm
445mm
65mm40mm
330mm
135mm
130mm

TROUBLESHOOTING
(USING JACK WITHIN RATED LOAD CAPACITY)
POSSIBLE JACK PROBLEMS
POSSIBLE CAUSES AND
SOLUTIONS
(Refer to Operation and
Maintenance procedures
for detailed information)
Release valve not tightly
closed.
To close or tighten, turn
release valve clockwise.
Air is in hydraulic system.
Release air from system.
Oil level is low in jack
Add oil as required
1. Oil reservoir is over-lled
Drain out some oil.
2. Lubrication of moving
parts is necessary.
Power unit is
malfunctioning.
Replace the power unit.
Jack will
not lift
load
Jack will
lift load,
but will
not hold
Jack will
not lower
completely
Poor jack
lifting.
Pump
feels
spongy
Jack will
not lift to
full height
Handle
raises by
itself when
jack is
under load
6
LUBRICATION
• Add lubrication oil to all moving parts
every 3 months.
PREVENTING RUST
• Check Piston Rod & Pump Piston
every 3 months for any signs of rust or
corrosion. Clean as needed and wipe
with an oily cloth.
• When not using the jack, always leave
the saddle & pump piston all the way
down.
KNOW YOUR JACK
Compare these illustrations with your
jack before operation and/or oil level
maintenance to become familiar with
the location of jack components.
RELEASE
VALVE
PUMP PISTON
DOWN
PROPER OIL
LEVEL
OIL FILLER
PLUG
PISTON ROD ALL
THE WAY IN

7
WARRANTY
1. This product is covered by an express warranty for 12 months from the date of purchase by
the original purchaser. Subject to the conditions of this warranty Shinn Fu Australia Pty Ltd
will replace the product or provide necessary parts on the product if the product is found to be
faulty within the warranty period due to defect in material or workmanship.
2. This warranty only applies to products imported by Shinn Fu Australia Pty Ltd and used within
Australia. Shinn Fu products imported by other importers are specically excluded.
3. This warranty only applies if the product has been used under normal conditions and in
accordance with the User Manual and that, in the opinion of Shinn Fu Australia Pty Ltd,
reasonable care has been taken of the product.
4. This warranty is void if the product has been tampered with or repaired by any unauthorised
person or has been modied in any way. Any abuse, misuse or subject to normal wear and tear
is not covered by this warranty.
5. If a warranty service is required the purchaser should:
a. Take the product to the nearest Shinn Fu Australia Pty Ltd repair agent or return it to the
place of purchase, at purchaser cost.
b. Provide evidence of proof of purchase and the date of purchase.
c. Provide details of the problem encountered.
6. The benets provided to the consumer by this warranty are in addition to other rights and
remedies available to the consumer under the law.
IF YOU REQUIRE ANY ASSISTANCE REGARDING WARRANTY CONDITIONS PLEASE
CONTACT THE SHINN FU AUSTRALIA PTY LTD COMPLIANCE OFFICER ON [phone]
OR EMAIL: [email protected]
Consumer Guarantees
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Shinn Fu (Australia) PTY. LTD.
15 Viewtech Place, Rowville, Victoria 3178, Australia