Pro-Lift T-9446 Instructions for use

Operating Instructions & Parts Manual
Scissors Jack
To avoid crushing and related injuries:
NEVER work under a load supported
only by a jack. ALWAYS use adequately
rated jack stands.
WARNING!
ATENCIÓN
• Leer, comprender, y seguir las
instrucciónes antes de utilizar el
aparato.
• El manual de instrucciónes y la
información de seguridad deben estar
comunicado en lengua del operador
antes del uso.
• No seguir estas indicaciónes puede
causar daños personales o materiales.
!
Printed in China
OIPM# SSJ-03
Model Number
T-9446
Capacity
3300 lb
Shinn Fu Company of America, Inc. © 2003
10939 N. Pomona Ave.
Kansas City, MO 64153
Phone [phone], fax [phone]
90 DAYS LIMITED WARRANTY
For a period of ninety (90) days from date of purchase, ShinnFuCo. of America,
Inc. will repair or replace, at its option, without charge, any of its products which fails due
to a defect in material or workmanship, or which fails to conform to any implied warranty
not excluded hereby.
Performance of any obligation under this warranty may be obtained by returning
the warranted product, freight prepaid, to ShinnFu Co. of America, Inc.Warranty Service
Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by
applicable law, (1) the CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE
REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE,
and (2) Shinn Fu Co. of America, Inc. SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE
DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF NINETY (90) DAYS FROM
DATE OF PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
OPERATION
Lifting
1. Place vehicle in park, with emergency
brake on and the wheel diagonally op-
posite from the wheel being lifted
chocked in both directions.
2. Insert the handle into the hole of the
handle socket. Center the saddle un-
der lift point. Jack shall be positioned
at 90 degrees perpendicular to the ve-
hicle frame seam.
3. Hold the front portion of the handle shaft
with one hand, and use the other hand
to crank the upright portion of the handle
clockwise.
4. Continue to crank it until you reach the
desired height, but never beyond a point
just high enough to remove and install
the tire.
Lowering
1. Crank the upright portion of the handle
counterclockwise.
2. After removing jack from under the load,
push saddle down to reduce ram ex-
posure to rust and contamination.
MAINTENANCE
Lubrication
Lubricate the thread and bearing with
wheel bearing grease. A periodic coating
of light lubricating oil to pivot points, axles
and hinges will help to prevent rust and
assure parts move freely.
Note: Never apply lubricant directly on top
of saddle.
Cleaning
Periodically check the jack for signs of rush
or corrosion. Clean as needed and wipe
with an oily cloth.
Note: Never use sandpaper or abrasive
material on these surfaces !
Storage
When not in use, store the jack with sad-
dle fully lowered.
4

2 3
Save these instructions. For your safety,
please read, understand and follow the
information contained within before use.
The owner and operator shall have an
understanding of this product and safe
operating procedures before attempting
to use. Instructions and safety informa-
tion shall be conveyed in the operators
native language before use is authorized.
Make certain that the operator thoroughly
understands the inherent dangers asso-
ciated with the use and misuse of the prod-
uct. If any doubt exists as to the safe and
proper use of this device as outlined in
this factory authorized manual, remove
from service until which time it is clear.
This jack is not suitable for use in lifting,
leveling and/or positioning houses, con-
struction trailers and dwellings in general.
Inspect before each use. Do not use if
cracked, broken, bent or otherwise dam-
aged parts are noted or if the jack is sus-
pected to have been subjected to a shock
load. Discontinue use until checked out
by an authorized factory service center.
Owner and operators of this device shall
be aware that no serviceable or replace-
able parts are available for this device. Do
not attempt to weld, rivet or otherwise re-
pair this device. It is recommended that
an annual inspection be done to this de-
vice by qualified persons and that miss-
ing or damaged labels, warning/safety
decals be replaced with ones that are fac-
tory authorized. Always reference the Prod-
uct Label and Owner's Manual to estab-
lish rated capacity. Figure 1 - Model T-9446 Nomenclature
Study, understand, and follow all printed
materials provided with and on this
device. Do not use this product before
reading and understanding the tire
changing procedures as outlined in the
vehicle owners manual or tire chang-
ing compartment of the vehicle. Do not
exceed rated capacity as outlined in the
height/weight curve (see Fig. 2). Use
only on hard, level surfaces capable of
sustaining rated capacity loads. Use for
emergency tire changing only. Never
put any portion of body under a vehicle
supported by the jack. Activate the haz-
ard warning flasher, turn off ignition, set
parking brake, move automatic trans-
mission to park position. In case of
manual transmission, put it in reverse
gear if car is facing downhill and low-
est gear if car is facing uphill. In addi-
tion, the wheel diagonally opposite from
the wheel being lifted shall be chocked
in both directions. Lift only on areas of
the vehicle as specified by the vehicle
manufacturer. Follow tire changing pro-
cedures as per vehicle owners manual.
Use ONLY the provided operating han-
dle or factory replacement. Failure to
heed these messages may result in
personal injury and/or property dam-
age.
!
WARNING
ATENCIÓN
!
PRODUCTDESCRIPTION
This jack is designed to safely and effec-
tively lift one axle of a vehicle for the sole
purpose of tire removal and/or installa-
tion.
BEFOREUSE
1. Verify that the product and the applica-
tion are compatible, if in doubt call Pro-
Lift Customer Support @ (816) 891-
6390.
2. Before using this product, read the
owner's manual completely and famil-
iarize yourself thoroughly with the prod-
uct, its components and recognize the
hazards associated with its use. Check
with vehicle owner's manual for proper
lift points.
HEIGHT / WEIGHT CURVE
This device is designed to sustain the fol-
lowing loads at these specified heights.
DO NOT EXCEED the rated capacity for
each position.
saddle
handle
socket
handle shaft
•Leer, comprender, y seguir las
instrucciónes antes de utilizar el aparato.
•El manual de instrucciónes y la
información de seguridad deben estar
comunicado en lengua del operador
antes del uso.
•No seguir estas indicaciónes puede
causar daños personales o materiales..
Figure 2 - Height/Weight Curve
Weight (Ibs)
Heigh (inches)
7 3/4
10 1/4
14 1/4
15
10
5
2500
1500 3300
1000
Height (inches) Weight (lbs)
7 ¾1500
10 ¼2500
14 ¼3300
!SAFETY MESSAGE !
Be sure all tools and personnel are
clear before lowering load. No altera-
tions shall be made to this device. Only
attachments and/or adapters supplied
by the manufacturer shall be used. Lift
only on areas of the vehicle as speci-
fied by the vehicle manufacturer.