ProLights Mosaico L User manual

USER MANUAL
REV.01-03/22 English version
Mosaico L
300W IP66 zoomable LED image projector
with an animation wheel and framing shutters

Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
Visit the download area
of the product page

PROLIGHTS - Mosaico L01
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 05
3 - INSTALLATION 06
MOUNTING.................................................................................................................... 06
4 - CONNECTION TO THE MAINS SUPPLY 07
5 - START UP 07
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 07
6 - PRODUCT OVERVIEW 08
7 - DMX CONNECTION 09
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 09
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 09
CONNECTION DAISY CHAIN........................................................................................ 09
CONNECTION OF THE DMX LINE................................................................................ 09
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 10
DMX ADDRESSING ........................................................................................................ 10
ETHERNET CONNECTION ............................................................................................ 10
ETHERNET OPERATION ................................................................................................ 10
ETHERNET TO DMX OPERATIONS ............................................................................... 11
OPERATION AS A WIRELESS TRANSMITTER................................................................ 11
IN TO WDMX ................................................................................................................. 11
OPERATION AS A WIRELESS RECEIVER........................................................................ 12
WDMX TO DMX (RX)...................................................................................................... 12
8 - CONTROL PANEL 13
DISPLAY AND BUTTONS LAYOUT................................................................................. 13
9 - MENU STRUCTURE 14
10 - SHORTCUT 23
11 - RDM FUNCTIONS 24
12 - DMX CHARTS 29
13 - GOBOS WHEEL 34
14 - COLOR WHEEL 35
15 - ANIMATION WHEEL 36
16 - REPLACING THE ANIMATION WHEEL 37
17 - GOBOS REPLACEMENT 39
18 - ERROR MESSAGES 40
19 - ACCESSORIES INSTALLATION 41
BRACKET FOR WALL MOUNTING AND SUSPENSION ON POLES (CODE MOSBRACK)
........................................................................................................................................ 41
20 - MAINTENANCE 42
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 42
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 42
TROUBLESHOOTING..................................................................................................... 43

PROLIGHTS - Mosaico L02
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, power-
ing, operating or servicing the product and observe the indications also for its future
handling.
This unit is not for household and residential use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, cable, or
other components are damaged, defective, deformed or showing signs of overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0,5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0.5 meters (1.64 ft) from the lens of the projector.
T
45°
C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).

PROLIGHTS - Mosaico L03
T
-20°
C
a
Minimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
IP66
Permanent Outdoor use
• This product is rated with an IP (Ingress protection) for permanent outdoor use when
used and serviced according to the instruction contained in this document.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
Light collimation optical system
• This product contains internal light collimation opticsl system. Avoid to expose the
optical system to any intense source of light (including sunlight) from any angle.
T
80°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 80 °C (176 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 2 according to EN 62471.
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
• The device should be positioned so that prolonged staring into the luminaire at a
distance closer than 28 m (82.4 ft) is not expected.

PROLIGHTS - Mosaico L04
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
28 m
82.4 ft
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/ recycle this product at the end of its life according to the local regulation.
The product contains a lithium ion battery
• Don't throw the unit into the garbage at the end of its lifetime.
• Make sure to dispose according to your local ordinances and/or regulations, to avoid
polluting the environment!
• The packaging is recyclable and can be disposed.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
• 2014/53/EU - Radio Equipment Directive (RED).
The products to which this manual refers comply with:
• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.
• UL 1012 + CSA C22.2 No. 107.1 - Standard for power units other than class 2.
FCC Compliance:
• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Other approvals
• The product meets the safety requirements of the certification procedures of the
market in which it is placed and sold.

PROLIGHTS - Mosaico L05
1 - PACKAGING
PACKAGE CONTENT
• 1x MOSAICOL;
• 1x BARE END - IP connection adapter;
• 1x 5p XLR - IP connection male adapter;
• 1x 5p XLR - IP connection female adapter;
• User Manual.
OPTIONAL ACCESSORIES
• WSBBR512G6: blackBox R-512 G6 receiver 512Ch, 2.45GHz,DMX&RDM,Bluetooth,G3,G4,G4S,G5,CRMX;
• WSBBR512G5: blackBox R-512 G5 receiver 512Ch, 2.45GHz & 5.8GHz, DMX/RDM optional;
• WSBBF1G6: blackBox F-1 G6 transrec, 512ch, 2.45GHz, DMX&RDM,Bluetooth,G3,G4,G4S, G5, CRMX;
• WSBBF1G5: blackBox F-1 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 512Ch;
• RSR1235A/B: steel security cable for hanging bodies, inox steel shackle, L=120 cm, silver/black;
• C6002A/B: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt;
• FCLMOSAICOL: ightcase for 2 pcs of MOSAICOL;
• MOSBRACK: bracket for MOSAICO series for wall mounting and suspension on poles;
• AWEXAC1L03: IP67 power extension cable for outdoor architectural projectors, L.03 m;
• AWEXAC1L05: IP67 power extension cable for outdoor architectural projectors, L.05 m;
• AWEXAC1L10: IP67 power extension cable for outdoor architectural projectors, L.10 m;
• AWEXAC1L20: IP67 power extension cable for outdoor architectural projectors, L.20m;
• AWEXDC1L03: IP67 DMX extension cable for outdoor architectural projectors, L.03 m;
• AWEXDC1L05: IP67 DMX extension cable for outdoor architectural projectors, L.05 m;
• AWEXDC1L10: IP67 DMX extension cable for outdoor architectural projectors, L.10 m;
• AWEXDC1L20: IP67 DMX extension cable for outdoor architectural projectors, L.20 m;
• UPBOX1U: rmware uploader kit, USB IN, 3pin XLR DMX OUT, USB OUT.
2 - TECHNICAL DRAWING
Fig. 01
Weight: 25 kg - 55.11 lbs

PROLIGHTS - Mosaico L06
Fig. 02
3 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,
auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the xture above ground level, secure it against failure of primary attachments by
attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor
point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-
pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
C6002 clamp
RSR1235A/B
Steel security cable
60 mm
[2.4 in]
119 mm
[4.7 in]
362 mm
[14.3 in]
Ø13 mm
[Ø0.5 in]

PROLIGHTS - Mosaico L07
5 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that
personal safety will not be put at risk when the xture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig-
nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
4 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the xture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a
grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts
about proper installation, consult a qualied electrician.
The max power consumption is 440W.
Core (EU) Core (US) Connection Plug terminal marking
Brown Black Live L
Blue White Neutral N
Yellow+green Green Earth

PROLIGHTS - Mosaico L08
3 4 5 6 7 8
1
2
6 - PRODUCT OVERVIEW
1. BRACKET;
2. USER INTERFACE with display and buttons for access to the control panel functions;
3. GORE VALVE;
4. POWER IN/OUT: for connection to the Mains 100-240V~/50-60Hz;
5. POWER IN: for connection to the Mains 100-240V~/50-60Hz;
6. DMX OUT (3-p XLR): 1 = GND, 2 = sign-, 3 = sign+;
7. DMX IN (3-p XLR): 1 = GND, 2 = sign-, 3 = sign+;
8. ANTENNA.
Fig. 03

PROLIGHTS - Mosaico L09
7 - DMX CONNECTION
CONNECTION OF THE CONTROL SIGNAL: DMX LINE
The product has XLR sockets for DMX input and output.
The default pin-out on both socket is as the following diagram:
Fig. 04
Pin1 : GND - Shield
Pin2 : - Signal
Pin3 : + Signal
Pin4 : N/C
Pin5 : N/C
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION
Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot trans-
mit control data reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters (1000 ft).
Heavier gauge cable and/or an amplier is recommended for longer runs.
To split the data link into branches, use splitter-ampliers in the connection line.
Do not overload the link. Up to 32 devices may be connected on a serial link.
CONNECTION DAISY CHAIN
Connect the DMX data output from the DMX source to the product DMX input (male connector XLR)
socket.
Run the data link from the product XLR output (female connector XLR) socket to the DMX input of the
next xture.
Terminate the data link by connecting a 120 Ohm signal termination. If a splitter is used, terminate
each branch of the link.
Install a DMX termination plug on the last xture on the link.
CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω im-
pedance and low capacity.
The following diagram shows the connection mode:
Fig. 05 - Example 6 DMX channels conguration
. . . . . . . . . . . .
DMX Address: 33 DMX Address: 51DMX Address: 39 DMX Address: 45
. . . . . . . . . . . .
DMX512 Controller
DMX IN DMX IN DMX IN DMX INDMX OUT DMX OUT DMX OUT DMX OUT

PROLIGHTS - Mosaico L10
DMX ADDRESSING
In order to start controlling the product via DMX, the rst step is to select a DMX address, also known
as the start channel, this is the rst channel used to receive instructions from a DMX controller. If you
wish to control the product individually, it is necessary to assign a different starting address channel to
each xture.
The number of channels occupied from the product depends on the DMX mode selected, so always
verify the DMX Mode in the MENU before start addressing.
If you assign two xtures the same address, they will be executing the same behaviour. Selecting the
same address to multiple xtures can be useful for diagnostic purposes and symmetrical control.
DMX addressing is limited to make it impossible to set the DMX address so high that you are left with-
out enough control channels for the product.
To set the xture’s DMX address:
1. Press ENTER to open the main menu.
2. Reach the addressing menu, then select the DMX ADDRESS settings.
3. Select the address from 1 to 512 using the navigation arrows/buttons and conrm by pressing
ENTER.
4. Press Menu to exit and return to the Home screen.
ETHERNET CONNECTION
The products is provided with two 8-pin RJ-45 sockets for Ethernet input/output for a simple daisy
chain connection to the network.
The product can be controlled with ArtNet (or others available) communication protocol.
Use a network cable category 5 (with four “twisted” wire pairs) and standard RJ-45 plugs.
ETHERNET OPERATION
Please refer to the section MENU STRUCTURE contained in this document for detailed informations
about the parameters of setting on the xture (Protocol, Net, Subnet, Universe, Start Channel and IP
Address, Ethernet to DMX No/Yes).
• About the IP addresses is recommended to set 002.xxx.xxx.xxx or 010.xxx.xxx.xxx.
• The submask net is xed at 255.0.0.0.
CONSTRUCTION OF THE DMX TERMINATION
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the male XLR
connector, as shown in gure.
Fig. 06
Example:
5 pin XLR connector
4

PROLIGHTS - Mosaico L11
ETHERNET TO DMX OPERATIONS
Please refer to the section MENU STRUCTURE contained in this document for detailed informations
This function allow a product receiving an ethernet signal protocol to re-transmit the incoming signal
onto a wired DMX line through its onboard XLR-out connector.
• An Ethernet protocol (Artnet, sACN or others available) has to be enabled from Ethernet menu
at rst xture. Please make sure that wireless receiver is switched to OFF if you use Ethernet
comunication.
• Enable the option Ethernet To DMX from the Ethernet menu at the rst product (connected to the
Ethernet) in the signal chain, next products have standard DMX setting.
• Connect the Ethernet input of the rst product in the data chain with the network. Connect the
DMX output of this product with the input of the next product until all products are connected to
the DMX chain.
• Caution: At the last product, the DMX chain has to be terminated with a terminator. Solder a 120 Ω
resistor between Signal (–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the
last product.
OPERATION AS A WIRELESS TRANSMITTER
MOSAICOL can be used as wireless transmitter to transmit DMX signal to different wireless receivers.
To use MOSAICOL as wireless transmitter, please follow the procedure below:
1. Push ENTER button untill you show CONNECT on display, then press ENTER button to conrm.
2. Use UP/DOWN buttons for select WIRELESS, then press ENTER to conrm.
3. Push ENTER button on WDMX ON/OFF function and enable it to ON.
4. Select WDMX mode and set it on Transmitter (please note that WDMX mode will be available only
if WDMX ON/OFF is set to ON).
5. Ensure that the receiver units are not connected to any other transmitter. Please refer to "Reset the
receiver" paragraph.
6. Enable TX LINK to ON to link transmitter to receivers (please note that TX LINK will be available only
if WDMX mode is set to Transmitter).
• The transmitter scans for all unlinked receivers for a period of about 5 seconds.
• If the connection fails, check the position of the receiver.
• The wireless icon on the receiver display indicates the received signal strength.
Unlinking the transmitter
Follow the procedure below to unlink the transmitter from all receivers connected with the unit.
1. Push ENTER button untill you show CONNECT on display, then press ENTER button to conrm.
2. Use UP/DOWN buttons for select Wireless, then press ENTER to conrm.
3. Enable TX UNLINK to ON 8 (please note that TX UNLINK will be available only if WDMX mode is
set to Transmitter).
• All connected receivers will be unlinked.
IN TO WDMX
This function enable or disable the transmission throught wireless of the DMX signal from the transmit-
ter side to the receiver.
Any incoming signal (ArtNet, sACN or DMX) is retransmitted throught wireless.
If the MOSAICOL protocol selected is ArtNet / sACN, the WDMX module will retransmit the DMX
values contained in the ArtNet / sACN signal received from the MOSAICOL.
NOTE: Artnet and sACN have higher priority on DMX if they are connected to transmitter.

PROLIGHTS - Mosaico L12
OPERATION AS A WIRELESS RECEIVER
MOSAICOL can be used as wireless receiver connected to a wireless transmitter.
To use MOSAICOL as wireless receiver, please follow the procedure below:
1. Push ENTER button untill you show CONNECT on display, then press ENTER button to conrm.
2. Use UP/DOWN buttons for select Wireless, then press ENTER to conrm.
3. Push ENTER button on WDMX ON/OFF function and enable it to ON.
4. Select WDMX mode and set it on Receiver (please note that WDMX mode will be available only if
WDMX ON/OFF is set to ON).
5. Enable RX RESET to ON to reset the receiver (please note that RX RESET will be available only if
WDMX mode is set to Receiver).
6. On the transmitter, enable TX LINK to ON to link transmitter to the receivers.
7. If the connection is successful and DMX input is available the display the display on the receiver unit
will shows the DMX address. If DMX signal is not available, the display will shows "No signal" but
keeps the transmitter linked.
8. If the connection fails, check the position of the receiver.
9. The wireless icon on the receiver display indicates the received signal strength.
Reset the receiver
Follow the procedure below to reset the receiver.
1. Push MENU button untill you show CONNECT on display, then press ENTER button to conrm.
2. Use UP/DOWN buttons for select Wireless, then press ENTER to conrm.
3. Enable RX RESET to ON.
• The wireless icon on the receiver display indicates the received signal strength.
WDMX TO DMX (RX)
This function enable or disable the retransmission of the wireless DMX signal received throught the
DMX port on the receiver side.

PROLIGHTS - Mosaico L13
Fig. 07
8 - CONTROL PANEL
The product has a display and buttons for access to the control panel functions.
NOTE: remove the display cover to access the control panel
DISPLAY AND BUTTONS LAYOUT
• MENU: used to access the menu tree or to return a previous menu window;
• UP: browse upwards through the menu list and increases the numeric value displayed;
• DOWN: browse downwards through the menu list and decreases the numeric value displayed;
• ENTER: used to conrm the current menu or conrm the current function value or option within a
menu.

PROLIGHTS - Mosaico L14
9 - MENU STRUCTURE
The following chart describes the MENU tree of the product, the terms shown in BOLD indicates the
default settings.
MENU
1 CONNECT DMX Address 001-512
DMX Mode BASIC
STANDARD
EXTENDED
Wireless WDMX ON/OFF ON/OFF
WDMX MODE TRANSMITTER/
RECEIVER
TX LINK ON/OFF
TX UNLINK ON/OFF
RX RESET ON/OFF
IN TO WDMX ON/OFF
WDMX TO DMX (RX) ON/OFF
2 SETUP Screen BACKLIGHT ON
10 s
20 s
30 s
FLIP DISPLAY ON
OFF
WARN ERRORS ON
OFF
KEY LOCK ON
OFF
Fixture FAN MODE AUTO
ON
SILENT
LED FREQUENCY 600 HZ
1200 HZ
2000 HZ
4000 HZ
6000 HZ
25K HZ
TEMPERATURE UNIT °C
°F
AUTO TEST
MANUAL TEST SHUTTER
DIMMER
COLOR
GOBO
GOBO ROT
PRISM
PRISM ROT
FROST
ZOOM
FOCUS
ANIMATION
ANIMATION ROT
FR.BLADES ROT.
FR.BLADE 1 MOVE.
FR.BLADE 1 SWIV.
FR.BLADE 2 MOVE.
FR.BLADE 2 SWIV.
FR.BLADE 3 MOVE.
FR.BLADE 3 SWIV.
FR.BLADE 4 MOVE.
FR.BLADE 4 SWIV.

PROLIGHTS - Mosaico L15
3 ADVANCED RESET ALL
COLOR
GOBO
PRISM
ANIMATION
FOCUS
ZOOM
FROST
FR.BLADES ROT.
FR.BLADE 1
FR.BLADE 2
FR.BLADE 3
FR.BLADE 4
ADJUST COLOR WHEEL
GOBO WHEEL
GOBO 1 FOCUS
…
GOBO 7 FOCUS
GOBO 1 INDEX
…
GOBO 7 INDEX
GOBO ROT
PRISM
PRISM ROT
ANIMATION
ANIMATION ROT
FOCUS ON OPEN
ZOOM ON OPEN
FROST
FR.BLADES ROT.
FR.BLADE 1 M1
FR.BLADE 1 M2
FR.BLADE 2 M1
FR.BLADE 2 M2
FR.BLADE 3 M1
FR.BLADE 3 M2
FR.BLADE 4 M1
FR.BLADE 4 M2
FACTORY RELOAD OFF
ON
4 INFORMATION FIXTURE TIME
TEMPERATURE
FANS SPEED
SOFTWARE
VERSION
RDM UID
MEMORY
ERROR MESSAGE
DMX VIEW
5STANDALONE PLAY OFF
SHOW Show 1
Show 2
Show 3
CHASE Chase 1
...
Chase 8
SCENE Scene 1
…
Scene 32
EDIT SHOW SHOW 1
SHOW 2
SHOW 3
CHASE 1
...
CHASE 8
ON
OFF
EDIT CHASE CHASE 1
...
CHASE 8
STEP 1
...
STEP 16
OFF
SCENE 1
...
SCENE 32

PROLIGHTS - Mosaico L16
EDIT SCENES SCENE 01
...
SCENE 32
NEW / EDIT Default:
Dimmer: 255
Shutter: 255
Focus: 128
Zoom: 128
Fr.shutter 1 Move:128
Fr.shutter 1 Swiv:128
Fr.shutter 2 Move:128
Fr.shutter 2 Swiv:128
Fr.shutter 3 Move:128
Fr.shutter 3 Swiv:128
Fr.shutter 4 Move:128
Fr.shutter 4 Swiv:128
All others at 0
COPY OFF
SCENE 1
...
SCENE 32
SCENES RECORD SCENE 01
...
SCENE 32
DMX - SCENES RECORD
SLAVE SETUP EDIT SCENE 01
...
EDIT SCENE 32
SCENES TIME SCENE 01 TIME
...
SCENE 32 TIME
FADE IN TIME 0.000 - 3600.0
HOLD TIME 0.000 - 3600.0
FADE OUT TIME 0.000 - 3600.0
CHASE TIME CHASE 1
...
CHASE 8
0.000 - 3600.0
MOVE WITH
BLACKOUT
SCENE 01
...
SCENE 32
OFF
ON
ADD MECH. TIME OFF
ON
6DMX 512 MODE OFF - ON
EDIT DMX SHOW RECORD DMX SHOW 1
...
DMX SHOW 8
SNAPSHOT SNAPSHOT 1
...
SNAPSHOT 16
PLAY DMX SHOW RECORD DMX SHOW 1
...
DMX SHOW 8
SNAPSHOT SNAPSHOT 1
...
SNAPSHOT 16
CLOCK SETTING CURRENT TIME
CLOCK SETTING
SCHEDULE SHOW SCHEDULE SHOW 1
...
SCHEDULE SHOW 16

PROLIGHTS - Mosaico L17
WIRELESS
• To enter the Wireless mode proceed in the following mode:
• Press the MENU button to access the main menu.
• Press the UP/DOWN button to scroll the menu, select Connect, then press the ENTER button to
enter the next menu.
• Select the Wireless Receive function using the UP/DOWN buttons, then press the ENTER button.
• To activate the Wireless Receive function, use the UP/DOWN buttons and select the On option.
• Press the ENTER button to conrm the selection.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
NOTE - Once you have performed these steps, you must synchronize with any WiFi unit with which you
want to communicate by pressing the sync button on it. At this point connect the DMX console to the
WiFi unit to open the communication with the MOSAICOXL.
• To reset the unit, select the Receive Reset function using the UP/DOWN buttons, press the RIGHT
button until the display shows Connect, then select Receive Reset using the UP/DOWN buttons,
then press the ENTER button.
• To activate the mode use the UP / DOWN keys and select the Yes option.
• Press the ENTER button to conrm the selection.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
• To activate the Wireless to DMX function, use the UP / DOWN buttons to press the ENTER button
until the display shows Connect, then select Wireless to DMX, then press the RIGHT button.
• To activate the mode use the UP/DOWN buttons and select the Yes option.
• Press the ENTER button to conrm the selection.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
SCREEN
It is possible to modify the following parameters, related to the display, following the same procedure:
• Press the MENU button to access the main menu.
• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button
access the next menu.
• Press the UP/DOWN button to select Screen and press the ENTER button to proceed.
• Select the proposed option with the UP/DOWN button and press the ENTER button to conrm.
-Backlight - Auto Off display backlight. This function allows you to switch off automatically the
backlighting of the display after a certain time which can be set using the directional keys. To
have the display always on select On or set a value between those shown (10s, 20s, 30s) to turn
off the display once the chosen time has elapsed, after exiting the menu.
-Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a
better view of the display when the unit is hanging upside down. Select Yes to activate the func-
tion, No to deactivate it or Auto.
-Warn Cue - Warning of error. Use the arrow keys to select Off or On depending on whether or
not the display shows error warnings.
-Key lock - With this function, you can lock the keys on the control panel to prevent, for example,
tampering with the settings. If this function is activated, the keys are locked automatically. To dis-
able or temporarily disable or disable the key lock function, press the keys in the following order
to regain access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate
the function or No to deactivate it.
• Press the ENTER button to conrm the selection.
• Press the MENU button repeatedly to exit the menu and to save the changes made.
FIXTURE SETTINGS
You can change the parameters for the device by following these steps:
• Press the button MENU to enter the menu mode.
• Use the buttons UP/DOWN to select Set Up. Press the button ENTER to conrm.
• Use the buttons UP/DOWN to select Fixture. Press the button ENTER to conrm.
• Press the buttons UP/DOWN to select the desired option and press the button ENTER to conrm:

PROLIGHTS - Mosaico L18
-Fan Mode - Fan speed. Select the desired fan speed Auto, Silent, High through the button UP/
DOWN.
-Temperature unit. Select Temperature unit function and then choose Celsius / Fahrenheit meas-
urement unit then press the ENTER button to conrm the selection.
• Press the MENU button repeatedly to exit the menu and to save the changes made.
AUTO TEST
Allow checking the proper functioning of the unit. Start the automatic test in the following way:
• Press the button MENU to enter the menu mode.
• Use the buttons UP/DOWN to select the Set Up. Press the button ENTER to conrm.
• Press the buttons UP/DOWN to select the Auto Test and press ENTER to conrm.
• To conrm and start the automatic test press the MENU button.
MANUAL TEST
It allows to do adjustments on the effects through comands pannel to obtain a perfect balance be-
tween the projectors.
• Press the button MENU to enter the menu mode.
• Press the buttons UP/DOWN to select the item Set Up. Then press the button ENTER.
• Press the buttons UP/DOWN to select the Manual Test. Then press the button ENTER.
• Select the effect you want change (Shutter, Dimmer, Color1, Cyan, Magenta, Yellow, CTO, Color,
Gobo, RGobo, PrismRot, Frost1, Frost2 Focus, Zoom, Effect, REffect, White, Zoom, Iris, Fr.shutters
Rot., Fr.shutter 1 Move., Fr.shutter 1 Swiv., Fr.shutter 2 Move., Fr.shutter 2 Swiv., Fr.shutter 3
Move., Fr.shutter 3 Swiv.,Fr.shutter 4 Move., Fr.shutter 4 Swiv.).Then press the button ENTER to
conrm.
• Use the directional buttons to calibrate the effect setting a value between 0 - 255. Then press the
button ENTER to conrm.
• Press repeatedly the button MENU to return the menu mode.
ADVANCED
It is possible to modify the following parameters following the same procedure:
• Press the MENU button to access the main menu.
• Press the UP/DOWN button to scroll through the menu, select Advanced, then press the ENTER
button to enter the next menu.
• Press the UP/DOWN button to select one off the following parametres:
-Reset - To start a preset program to restore the selected function (All, Cyan, Magenta, Yel-
low, CTO, Color, Gobo, Prism, Effect, Focus, Zoom, Frost, Iris, Fr.shutters Rot., Fr.shutter 1 M1,
Fr.shutter 1 M2, Fr.shutter 2 M1, Fr.shutter 2 M2, Fr.shutter 3 M1, Fr.shutter 3 M2, Fr.shutter 4
M1, Fr.shutter 4 M2).
-Adjust - To allows you to change all parameters. Insert the password "050" to enter. Select the
desired function (Cyan, Magenta, Yellow, CTO, Color, Gobo, RGobo, Prism, Rot Prism, Effect,
Focus, Zoom, Frost 1, Frost 2, Iris, Fr.shutters Rot., Fr.shutter 1 M1,, Fr.shutter 1 M2, Fr.shutter 2
M1, Fr.shutter 2 M2, Fr.shutter 3 M1, Fr.shutter 3 M2, Fr.shutter 4 M1, Fr.shutter 4 M2) and the
choose the value (0 - 255).
-Factory Reload - To reset the unit. Select Yes or No and select ENTER to conrm.
• Press the ENTER button to conrm the selection and wait for the selected function to be restored.
• Press the MENU button repeatedly to exit the menu and to save the changes made.
INFORMATION ON THE DEVICE
To view all the information on the device, proceed as follows:
• Press the MENU button to access the main menu. Press the UP/DOWN button to select Information,
then press the ENTER button to access the next menu.
• Press the UP/DOWN button to scroll through the menu, then select one of the following informa-