Yale Assure Lock YRD426 Technical specifications

P/N - - Rev FYRL TSINSTL FUL
1
Yale Assure Lock
®®
Touchscreen Deadbolt
Installation and Programming Instructions
( 226/YRD426)YRD
®
x3
#8-32 x 5/16"
Machine screws
x4
#7 wood & #8-32
machine x 20mm
Combination screws
x2
M6x59.5mm
Long through bolt
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO
THE PRODUCT AND VOID THE FACTORY WARRANTY
Optional
Network Module
Before you begin
for step-by-step installation
instructions & to register
your product
DOWNLOAD
THE BILT APP

P/N - - Rev FYRL TSINSTL FUL
2
Preparing Door

P/N - - Rev FYRL TSINSTL FUL
3
Optional Fire Kit Parts
For Model 620YRD ONLY
Installing Optional Fire Cup
Inside of Door
O
optional
O
optional

P/N - - Rev FYRL TSINSTL FUL
4
O
x4
1
d faute
2-3/8" position
2-3/4" position
Installing Latch & Strike Plate
Press
Pull
optional
Bolt must be in retracted
(unlocked) position. Note
horizontal orientation of
mechanism.

P/N - - Rev FYRL TSINSTL FUL
5
2Installing Touchscreen Escutcheon
Outside of DoorInside of Door
Bolt must be in retracted (unlocked)
position. Note horizontal orientation
of mechanism.
O
optional

P/N - - Rev FYRL TSINSTL FUL
6
x2
3Installing Interior Mounting Plate
Loosen screw to
remove cover.
O
optional

4Attaching the Cable Assembly
P/N - - Rev FYRL TSINSTL FUL
7

P/N - - Rev FYRL TSINSTL FUL
8
x3
5Installing Interior Escutcheon

3
Testing Operation
Bolt must be in retracted
(unlocked) position before
installing batteries.
P/N - - Rev FYRL TSINSTL FUL
9

P/N - - Rev FYRL TSINSTL FUL
10
2
Testing Operation

P/N - - Rev FYRL TSINSTL FUL
11
6Installing Optional Network Module

P/N - - Rev FYRL TSINSTL FUL
12
7Installing Batteries & Cover
Congratulations, you've installed the Yale Assure Lock
®®
Touchscreen Deadbolt ( 226/YRD426)!YRD
Continue with Programming Instructions to customize your product.
Tighten screw
to replace cover.
"Welcome to
Yale Real Living."

Programming Instructions
OR
Master Code must be created before any further programming.PIN
Max User Codes = 250 with Z-Wave Plus or ZigBee network module
Max User Codes = 25 without network module or with iM1 network module
Nax User Codes = 12 with Bluetooth
Interior Escutcheon
Privacy
Mode
Button
Speaker
"P" Key
(Return to Previous)
Low Battery
Indicator
Lockout
Mode
Exterior Escutcheon
P/N - - Rev FYRL TSINSTL FUL
13

1Creating a Master Code must be performed upon installation or after resettingPIN
the lock to factory default. Programming and use of lock is not possible until this
step has been successfully completed.
"Register Master
Code. Press the gear
key to continue."
"Enter a 4 to 8 digit
code followed byPIN
the gear key."
"Registered."
Enter 4-8
digit Master
Code.PIN
Press
Press
Creating Master CodePIN
P/N - - Rev FYRL TSINSTL FUL
14

2Creating User CodesPIN
Master code must be created first.PIN
*Max user codes = 250 with Z-Wave Plus or ZigBee network module
Max user codes = 25 without network module or with iM1 network module
Max user codes = 12 with Bluetooth
"Menu Mode,
enter number,
press the gear key
to continue."
Enter Master
codePIN
Press
Press
Press
Press
Press
Press
Enter 4-8 digit codePIN
Press
Enter 4-8 digit codePIN
Press
(code flashes)
Adding more *User Codes: To end programming:
Press
P/N - - Rev FYRL TSINSTL FUL
15

P/N - - Rev FYRL TSINSTL FUL
16
3
PIN Code Management (With Network Module - Up to 250 Users)
Master
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
Enter CodePIN
Press
Code Chart Duplicate if necessary
User Name
User Type PIN Code
Unlocking Door with CodePIN
User #

P/N - - Rev FYRL TSINSTL FUL
17
Interior Escutcheon
Resetting Lock to Factory Default
Reset
Button
When lock is reset to factory defaults all user codes (including the
Master code*) are deleted and all programming features are resetPIN
to original default settings (see below).
1. Remove the battery cover and batteries.
2. Remove the interior escutcheon to access the reset button.
3. The reset button (see image at right) is located beside the PCB
cable connector.
4. While pressing the reset button (minimum of 3 seconds) reinstall
batteries. Release reset button.
5. Replace battery cover.
Upon reset, Master Code creation is the only option available andPIN
must be performed prior to any other programming of the lock.

P/N - - Rev FYRL TSINSTL FUL
18
Factory Settings
*The Master code must be registered prior to any other programming of the lock.PIN
Registration required*
Settings Factory Setting
Master CodePIN
Automatic Re-lock Disabled
Lockout Mode Disabled
Language Setting English
Wrong Code Entry Limit 5 Times
Shutdown Time 60 Seconds
Volume Setting Enabled (Low)
Privacy Setting Disabled
One Touch Locking Enabled
Inside Indicator Light Disabled (Off)
Automatic Re-lock Time 30 Seconds
Escape Return Mode (Model 620 only)YRD Disabled

P/N - - Rev FYRL TSINSTL FUL
19
Definitions
All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user (except
Master) code access. When attempting to enter a code while the unit is in Lockout, the locked padlockPIN RED
will appear on the screen.
Automatic Re-lock Time: After a successful code entry and the unit unlocks, it will automatically re-lock after
thirty (30) seconds.
Inside Indicator Light: Located on the interior escutcheon. Shows active status (Locked) of lock and can be
enabled or disabled in the (Main Menu selection #3).Advanced Lock Settings
Language Setting Mode: Choosing English (1), Spanish (2) or French (3) becomes the (default) setting for the
lock's voice prompts.
Low Battery: When battery power is low, the Low Battery Warning indicator flashes . If battery power isRED
completely lost, use the cylinder key override.
Master Code: It must be createdPIN The Master code is used for programming and for feature settings.PIN
prior to programming the lock. The Master code will also operate (unlock/lock) the lock.
Network Module Setting: With the optional Network Module installed, this setting becomes available thru the
Main Menu (7) and allows the lock to connect with a network controller.
One Touch Locking: When the latch is retracted, activating the keypad will extend the latch (during Automatic Re-
lock duration or when Automatic Re-lock is disabled). When One-Touch Re-lock is in use anynot (disabled),
valid code will re-lock the lock.PIN
Previous: While in Menu Mode, pressing this icon cancels the current operation and returns the user to the
previous step.
Privacy Mode: Privacy mode is disabled by default. Enable Privacy Mode by pressing the privacy button for 4
seconds to put the lock in do-not-disturb mode (all pin codes are disabled).
Shutdown Time: The unit will shutdown (flashing ) for sixty (60) seconds and not allow operation after theRED
wrong code entry limit (5 attempts) has been met.
Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door.
User Code:PIN The user code operates the lock. The maximum number of user codes with Z-Wave Plus or
ZigBee network module is 250; without network module or with iM1 network module, maximum is 25; with
Bluetooth, maximum is 12. Note: When deleting user pin code(s), screen will display user pin code being deleted.
Volume Setting Mode: Low (2)The volume setting for code verification is set to by default; otherwise it canPIN
be set to or for quiet areas.High (1) Silent (3)
Wrong Code Entry Limit: After five (5) unsuccessful attempts at entering a valid code, the unit will shutPIN
down and not allow operation.

P/N - - Rev FYRL TSINSTL FUL
20
*The Master code must be registered prior to any other programming of the lock.PIN
1. Touch screen with back of hand or palm to activate.
2. Enter 4-8 digit master code* followed by key.PIN
Lock Response: "Menu mode, enter number, press key to continue."
3. Enter digit corresponding to the function to be performed followed by the key.
Follow the voice commands.
M
U
**This function appears only with
network module installed.
Default settings
in bold.
Master Code SettingPIN
User Code RegistrationPIN Continue
Complete
Register
Delete
Continue
Complete
M
231
Join the Network
Enable
Disable
English
Spanish
French
Silent
Low
High
Complete
Exit the Network
Volume Setting
Language Setting Mode
Lockout Mode
**Network Module Setting
Privacy Setting Mode Enable
Disable
Handing the Lock Preforms automatic
handing of the lock
Advanced Lock Settings Automatic Re-lock Disable
30 sec
Inside Indicator Light
One Touch Locking Enable
Disable
Enable
Disable
Continue
60 sec
3 min
2 min
Continue
Complete
Model 226 Feature Programming ThroughYRD
Menu Mode Using Master code*PIN