promotal 2060-10/2060-30 User manual

Model Shown : 2065-30
User’s Guide
VARIABLE HEIGHT COMBINED
EXAMINATION TABLE
2060-10/2060-30
2064-10/2064-30
2065-10/2065-30

Product Identification
(The information below is required when calling for service)
Serial Number :
Model Number :
Date of Purchase : Name of Owner / Facility :
Name of Dealer : Dealer’s Phone Number :
Promotal Authorized Service Company :
Serial number
The descriptions and features in this user’s guide are deemed correct at the time of printing.
Promotal reserves the right to change or to delete these models and procedures without prior notice.

Table of Contents
Important Information 6
Safety symbols 6
Power supply 6
Electromagnetic interferences 6
Installation Instructions 7
Material delivered in cardboard packaging 7
Fixed articles, furniture, wall furniture 7
Dismounted material 7
Products delivered on wooden palettes 7
Storage condition 8
Unpacking 8
Authorized CE representative 8
Instructions for Use 9
Warning 9
General maintenance 9
Maintenance Instructions 9
Painted surfaces 9
Imitation leather coverings 9
Stainless steel products 10
Chrome nished products 10
PVC and ABS products 10
Laminated elements 10
Dimensions 11
User’s Guide – Examination Couch 12
Features 12
Normal use 12
Electrical connections 12
Using the Couch 13
Connecting the hand control 13
Using the hand control 13
Adjusting the height 14
Adjusting the trendelenburg position 14
Adjusting the backrest tilt 15
Adjusting the backrest tilt 15
Integrated stirrups 16
Installing the integrated stirrups 16
Installing the stirrups 16
Using the pair of legrest 16
Installing the legrests 16

the levellers 17
Adjusting the levellers 17
Using the Block’n Roll
®
17
Plastic pan (6 liters) 17
Paper roll 18
Installing the paper roll 18
Removing the upholstery 18
Accessories 18
Rails 25x10 with clamps 18
Installing the rail 18
Installing the Clamps 18
Clamps (reference 25351) 19
Installing the Clamps 19
Clamps (reference 166) 19
Using the Clamps 19
Installing the Clamps 19
The pair of stirrups 20
Installing the stirrups 20
The pair of Goeppels « Goeppels » 20
Installing the Goeppels « Goeppels » 20
The hand grips 20
Installing the hand grips 20
Arm rest 21
Adjusting the arm rest 21
Auto-blocking I.V. pole 21
Adjusting the height of the IV pole 21
Installing the IV pole 21
The pair of barriers 22
Installing the pair of barriers 22
Using the pair of barriers 22
To raise the pair of barriers 22
To lower the pair of barriers 22
LED lamps 23
Adjusting the LED lamps 23
Head cushion 23
Installing 23
Using the pedal control 23
Pair of covers for legrests (for 840) 23
Plastic bowl with drainage tube. 24
Splash guard cover 24
Accessories 25

Options 25
Using the castors 25
Face slit in head cushion 26
Options 26
Lifespan 27
Exchangeable components 27
Obligatory/specic maintenance 27
Maintenance Notebook 28
Notes 29
Warranty Information 30
warranty 30
Obligations 30
Exclusions 30
Exclusive remedy 30
No authorization 30
Declaration of Conformity 31

Important Information
Safety symbols
Consult User Guide Keep dry
for important information
Proper shipping orientation Maximum stacking height
(palletted units)
Fragile Fuse rating specifi cation
Type B, Applied Part Dangerous voltage /
shock hazard
Protective earth ground Duty Cycle
(motor run time) :
1 minute ON /
9 minutes OFF
Certifi cation norm
Power supply
Electromagnetic interferences
This Promotal examination equipment was designed and built in order to minimize electroma-
gnetic interferences with other devices. If interferences are noted, it is necessary to withdraw the
parts causing the interference and/or to connect the equipment on isolated circuits.
Caution
Indicates a potentially hazardous situation which could result in injury if not avoided.
Equipement alert
Indicates a potentially hazardous situation which could result in equipment damage
if not avoided.
Note
Amplifi es a procedure, practice, or condition.
Caution
Most exposed metal parts of the equipment are electrically grounded. When performing
a cauterization or similar treatment, the patient must be insulated from the metal por-
tions of the equipment by nonconductive material. Failure to do so could result in electric shock
or burns to patient.
6 User’s Guide

Important Information
Safety symbols
Consult User Guide Keep dry
for important information
Proper shipping orientation Maximum stacking height
(palletted units)
Fragile Fuse rating specifi cation
Type B, Applied Part Dangerous voltage /
shock hazard
Protective earth ground Duty Cycle
(motor run time) :
1 minute ON /
9 minutes OFF
Certifi cation norm
Power supply
Electromagnetic interferences
This Promotal examination equipment was designed and built in order to minimize electroma-
gnetic interferences with other devices. If interferences are noted, it is necessary to withdraw the
parts causing the interference and/or to connect the equipment on isolated circuits.
Caution
Indicates a potentially hazardous situation which could result in injury if not avoided.
Equipement alert
Indicates a potentially hazardous situation which could result in equipment damage
if not avoided.
Note
Amplifi es a procedure, practice, or condition.
Caution
Most exposed metal parts of the equipment are electrically grounded. When performing
a cauterization or similar treatment, the patient must be insulated from the metal por-
tions of the equipment by nonconductive material. Failure to do so could result in electric shock
or burns to patient.
User’s Guide 7
Material delivered in cardboard packaging
�Small, lightweight, easy to
handle materiel
In this case, the products can be easily handled
without any lifting gear, taking care to position
the product according to the directional arrows
on the packaging.
In the absence of arrows indicating the top and
bottom, use the position of the various product
identity labels which are always placed at the
top.
�Heavy or cumbersome material
requiring the use of lifting gear
In this case, it is possible to use a fork lift truck,
provided it is used correctly.
Before moving, ensure the material is properly
positioned, and that the load is evenly balan-
ced.
Fixed articles, furniture, wall furniture
When the cardboard carton has been taken
away, remove remaining protective packaging
and install the product.
For wall furniture, make sure the following two
devices are properly installed : a suitable wall
fixture, a levelling device.
For other products, before installing, check that
the product is stable.
For certain models, adjustable levellers enable
you to improve this stability, and to make sure
the article is level.
If the product has separate accessories, fol-
low the accompanying mounting instructions to
attach them (shelves, glass doors, shelf sup-
ports).
Dismounted material
These products are delivered unassembled.
The various elements are protected by the following types of packaging :
– plastic (vinyl) packaging,
– bubble film packaging / foam or polystyrene,
– cardboard packaging.
Products delivered on wooden palettes
Products placed on a wooden palette may easily be moved using a forklift truck, provided this is
used correctly.
Before moving, ensure the truck is correctly positioned in relation to the palette, and that the
whole is stable.
You must pay particular attention when handling very tall or high articles (eg. cupboards).
Installation Instructions

Unpacking
When installing, remove all staple clips and
carefully remove the cardboard packaging.
Fragile parts of the product (upholstery cove-
rings, plastic casings, etc.) may be just below
the packaging. Care must be taken with cutting
instruments.
Once the packaging has been removed, remo-
ve any remaining protective covering.
In the case of packaging on a wooden palette,
remove the packaging as above. Depending
on the model, the product is fixed either by
screwed flanges, or by nailed wooden stakes.
Use a spanner (for metal flanges). Use a claw
hammer (for wooden stakes). Lift the article off
the palette, and take away the remaining pro-
tective covering. The product is now ready for
use.
Storage condition
Ambient Temperature Range : -5 °C to +38 °C (+23 °F to 100 °F)
Relative Humidity 10 % to 90 % (non-condensing)
Atmospheric Pressure 500 hPa to 1060 hPa (0.49 atm to 1.05 atm)
The following conditions must be observed
when storing any material :
– The area must be clean, well ventilated
and be of a normal temperature.
– Store products away from the elements,
and away from direct sunlight.
– The area must not be damp.
– The products must not be subject to
bumps or jolts.
– Do not store in an area where people
are likely to pass.
– Articles must not be stacked on top of
each other.
– Articles must remain in their original
packaging until final delivery.
Note :
Authorized CE representative
Countries in the EEC should direct all questions, incidents, and complaints to
Promotal’s Authorized CE representative listed below
:
Promotal
22, Rue De St. Denis
53500 Ernee,
FRANCE
Phone: + 33 243 05 6895
Fax: + 33 243 05 7200
8 User’s Guide

User’s Guide 9
Warning
You must read the installation instructions,
technical instructions, and instructions for use
before handling this equipment. The instrument
must be used only for the specific purpose for
which it is designed, and which is described in
our literature. The assembly and connection to
the mains must be carried out by qualified per-
sonnel. Under no circumstances must electrical
parts (motor, unit housing the electrical control
systems, control unit, adaptor etc.) be opened.
PROMOTAL cannot be held responsible for
any damage resulting from the instructions not
being followed.
General maintenance
Except for appropriate regular cleaning, our
products do not require any particular main-
tenance. The mechanical parts used as bloc-
king mechanisms (smooth arch, notched arch,
ratchet mechanisms, etc.) do not require any
specific attention. The gas springs on tables do
not require any maintenance. Their shaft must
be kept clean, must not be subject to jolts or
hard knocks, and must not be cleaned with any
corrosive products. The electric and hydraulic
jacks do not require any particular attention.
The variable height tables, chairs and trolleys
are equipped either :
– With arms fitted with self lubricating ar-
ticulation rings.
– With telescopic bearing runners. In this
case they should be lubricated once
a year (particularly if the runners are
noisy) with ordinary grease. (See the
exploded drawings for access to the
runners).
Maintenance Instructions
Painted surfaces (epoxy polyester finish)
The use of ordinary cleaning products, eg. window cleaning products, is perfectly suitable for
cleaning surfaces finished in epoxy polyester. It is strictly forbidden to use the following :
– Solvants : Petrol
High-grade alcohols :
– Aliphatics
– Aromatics
Ketones - esters
Tri -perchlorethylene
– Bases : 10 % sodium
10 % ammonium
– Acids : 30 % nitric
30 % chlorhydric
10 % citric
– Others : Distilled water
Bleach
Abrasive powders
Any abrasive
Cleaning product
Imitation leather coverings
Use a damp cloth and soapy water (eg. house-
hold soap). For stubborn stains, dab, but do not
rub, using a cloth soaked in white spirits or in
a solution of water and alcohol (less than 30 %
strength).
It is strictly forbidden to use the following :
Pure alcohol, acetone, perchlorethylene, tri-
chlorethylene, all solvants and detergents, any
abrasive cleaning agents, any kind of wax.
Flame retardort classification : All our cove-
rings class are M2 or M1. We can provide you
with a manufacturers certificate on request.
Instructions for Use

10 User’s Guide
Stainless steel products
Cleaning and Maintenance : For maintenan-
ce of stainless steel products, periodic clea-
ning of the surface is sufficient. This operation
is necessary to keep the products clean, but is
facilitated by the quality of stainless steel sur-
faces. A large range of products and cleaning
methods may be used. The choice of the most
suitable products to be used will depend on the
nature of the marks or on the product content,
and on the conditions of use of the stainless
steel elements.
Cleaning agents :
a) Detergent - washing liquids : All types
of detergents, washing liquids and com-
mercial soaps may be used, provided
they do not contain any chlorine pro-
ducts.
b) Abrasive powders : These products
may scratch the stainless steel surface,
thereby changing the way it looks, at
least in places. They should therefore
not be used.
c) Solvants : The use of solvants may be
useful in getting rid of grease marks.
The usual solvants (benzene, methyle-
ne chloride, white spirits etc.) as well as
domestic or specially prepared indus-
trial products may be used. Naturally
their use requires certain precautions to
be taken because of their inflammable
and toxic properties. Precautions must
also be taken to avoid damaging adja-
cent materials which may be sensitive
to their chemical action (paints, mastics,
joints etc.).
d) Acid products : Vinegar (acetic acid)
may be used to get rid of stains made
by calcium deposits. Its contact with the
surfaces must be of a very limited dura-
tion, and the surface must then be tho-
roughly and carefully rinsed with clean
water. The use of chlorine based pro-
ducts is forbidden.
e) Bases : They are strictly forbidden.
Others : The use of steel wool or metal spon-
ges is strictly forbidden.
Laminated elements
Cleaning and Maintenance : As for PVC. Use window cleaning products.
PVC and ABS products
Cleaning and Maintenance : The use of commercial cleaning products, such as window clea-
ning products, are perfectly suitable for PVC and ABS surfaces. To brighten up an old or dull
surface, plastic restorer products may be used. Please note that the use of any solvants or any
abrasive products is strictly forbidden.
Chrome finished products
These products have been covered with a chrome coating to protect them from oxydization.
Cleaning and Maintenance : It is vitally important, in order not to damage this protective coating,
that abrasive and / or corrosive products should not be used. The use of commercial cleaning
products, such as window cleaning products, are perfectly suitable for chrome coated surfaces.
If necessary, an appropriate disinfectant may be used on chrome (make sure the instructions are
followed).

User’s Guide 11
Dimensions

12 User’s Guide
Normal use
This examination couch enables the doctor to carry out general medical treatment, and
meets the following important requirements :
Easy positioning of the patient
Close position of the practitioner
Only nursing staff, hospital service staff and technical service staff should handle or use
the examination couch.
Patients or people accompanying them must not operate the examination couch. They
must not touch the control switches or levers.
This equipment must not be used in the presence of an ignitable anaesthetic air mix,
or with oxygen or nitrous oxide.
Electrical connections
This equipment must be connected to the main electricity supply.
Connection to the supply : 120 V or 230V
(depending on country)
Frequency : 50/60Hz
 ProtectionClassication/Degreeofelectricshockprotection: Class2/B
Power absorbed : 300W
Intermittent function mode : 1min / 9min
Maximum patient weight of 200 kg (tested at a static weight of
800kgandtestedatadynamicweightof250kg).
User’s Guide – Examination Couch
If the couch is not to be used for a prolonged period of time, it should be switched off and
disconnected from the mains.
Features
200kgPatientweightcapacity(testedatadynamic
weightof250kgandastaticweightof800kg)
Electric variable height from 49cm to 95cm
Steelframewithlightgreyepoxynish
Trendelenburg / Reverse Trendelenburg
Gas-springassistedexternalbackrest
Electriccentralbackrest
73cm upholstery width with reinforecd sides
Removable seamless seat upholstery
UpholsterywithclassM1ameretardantcovering
Hand control
Adjustable levellers under base
Removable sliding plastic pan (6 litre capacity)
2 paper roll holders (max length 60cm - ø 15cm)
Mobile hoist compatibility – clearance of 12cm
Possibility of 2 extra control connections

User’s Guide 13
Using the Couch
Safety :
For safety reasons, and in order to avoid malfunctioning, no objects should be
placed under the seat cushion or between the moving parts of the couch.
Using the hand control
To achieve the desired position, simply apply
and maintain pressure on the hand control. As
soon as this pressure is released, the move-
mentwillstop.Thecouchisttedwithaninter-
nal device to limit the high and low positions.
Connecting the hand control
Possible to connect 3 controls.

14 User’s Guide
Adjusting the trendelenburg position
Press on the hand control for the desired position.
Adjusting the height
Press on the hand control for the desired position. Up
Down
Up
Down

User’s Guide 15
Caution
The patient must not lean with his / her full weight on the backrest during this
procedure.
L1
Adjusting the backrest tilt
With one hand, move the lever (L1) either
up or down, with the other hand lower or
raisethebackresttothedesiredposition.
Adjusting the backrest tilt
Press on the hand control for the desired position.
Up Down

16 User’s Guide
Caution
Clamps are necessary to install these accessories (ref. : 166-50)
2
1
1
2
Integrated stirrups
(Only for models 2065-10 and 2065-30)
Installing the integrated stirrups
1. Pull the stirrup out, then unfold
2. Lift the stirrup slightly, then move it left or right
as desired.
3. Releasestirruptolockinposition.
Be sure the stirrups are locked in place
before using.
The stirrups will not support the patient’s
entire weight.
1
2
Using the pair of stirrups or pair of leg (Ø 16)
(Only accessories for models 2065-10 and 2065-30)
Installing the stirrups
(for models 2060-10 and 2060-30)
(reference 850)
Unscrew the screws (1) (on both sides of the
table) and insert the pair of legrests. The height
can be adjusted and the legrests can pivot on
the vertical axis (2).
Tighten the screws before use.
Installing the legrests
(for models 2064-10 and 2064-30)
(reference 840)
Unscrew the screws (1) (on both sides of the
table) and insert the pair of legrests. The height
can be adjusted and the legrests can pivot on
the vertical axis (2).
Tighten the screws before use.

User’s Guide 17
Caution ensure the plastic pan
is correctly positionde.
Plastic pan (6 liters)
The plastic pan is removable to ensure easy
cleaning, it can be moved towards the front and
also be placed under the seat.
Pull the handle underneath the seat, to
move the pan forward.
Remove the pan.
the levellers
Adjusting the levellers
Screw or unscrew the leveller (P) to the desi-
red height.
P
Using the Block’n Roll®
(for models 2065-30, 2060-30 and 2064-30)
Caution
Ensure the table is in a working position before placing a
patient on the table.
WorkingpositionMoving position
Caution :
Must not be use with the patient, This system is only to be used to move the
table for cleaning purposes.

18 User’s Guide
Rails 25x10 with clamps
(Only accessories for models 2065-10 and 2065-30) (reference 2065-78)
(Options for models 2060-10, 2064-10, 2060-30 and 2064-30) (reference 2061-78)
Installing the rail
On each side :
1x A3A105-02 Seat rail
4x A3A105-XX Stainless steel spacer tube
4xECX4008 SafetynutD.8
4xRDN0008 GreynutcoverD.8
4x VXM3084 Screw
Installing the Clamps
Insert The clamps on the rails.
The clamps accept accessories with Ø16 and
Ø18.
1
2
Accessories
Removing the upholstery
Raise the base by doing the 2 studs (P).
(Operation to be carried out for regular cleaning)
Paper roll
Installing the paper roll
The paper roll is positioned on an axis with
spring clips at each end. Press these springs
to remove the paper roll.
Cover the upholstery with paper
before use.
RP
P
N°5 Allen key
Box spanner of 13
Tighten the screws before use.

User’s Guide 19
Using the Clamps
Loosen the nuts (V) and Installing the accessories.
Tighten the nuts.
The clamps accept accessories with Ø16 and Ø18.
V
Installing the Clamps
Takethestopper(B) out of the square tube if
necessary. Loosen the nuts (V), and put the
pair of clamps ref.166 (E) into position in the
square tubes. Tighten the nuts.
The clamps accept accessories with Ø16
(only).
Clamps
(reference 166)
V
B
E
Tighten the screws before use.
Clamps
(Standard for models 2060-10, 2064-10, 2060-30 and 2064-30)
(only accessoires for models 2065-10 and 2065-30) (reference 25351)
Installing the Clamps
On each side :
1xD117300 Clamp
2x VXM7082 Screw TH 8x20
2xECX4008 SafetynutD.8
2xRDN0008 GreynutcoverD.8
Box spanner of 13
x2

20 User’s Guide
1
2
The pair of stirrups (Ø 18)
(reference 12850 only for models 2065-10 and 2065-30 )
(reference 2061-50 for models
2060-10 and 2060-30 )
Installing the stirrups
Unscrew the screws (1) (on both sides of the
table) and insert the pair of stirrups. The height
can be adjusted and the stirrups can pivot on
the vertical axis (2).
Tighten the screws before use.
Caution Clamps are necessary to
install these accessories.
(ref. : 166-50).
The pair of Goeppels (Ø 18)
2
1
3
(reference 12845 only for models 2065-10 and 2065-30 )
(reference 2061-45 for models
2064-10 and 2064-30 )
Installing the Goeppels
Unscrew the screws (1) (on both sides of the
table) and insert the pair of goeppels. The
height can be adjusted and the goeppels can
pivot on the vertical axis (2).
Tighten the screws before use.
A ball and socket joint allows to move the
goeppels in all directions. To do so, loosen the
grip (3).
Tighten the screws before use.
The hand grips
(reference 856)
Installing the hand grips
Unscrew the screws (on both sides of the table)
and insert the pair of hand grips.
Tighten the screws before use.
Caution Clamps are necessary to
install these accessories.
(ref. : 166-50).
Caution Clamps are necessary to
install these accessories.
(ref. : 166-50).