PROPOINT 8886442 User manual

V1.0 8886442
Please read and understand all instructions before use. Retain this manual for future reference.
GREASE GUN

19.2V DC

8886442 19.2V Cordless Grease Gun V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Voltage Rating 19.2V
Battery Capacity 1.5 Ah
Charger Input Voltage 120V
Maximum Operating Pressure 6,000 PSI (413 BAR)
Grease Reservoir Capacity 14 oz (400 gms)
Ouput 3 oz/min. (85 gms/min.)
Hose/Pipe Type Flexible
Hose/Pipe Length 30 in.
Tube Material Steel
Automatic Air Bleeder Yes
Filling Method Cartridge Loading / Bulk Fill/ Filler Pump /
Suction Fill
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice
that could result in severe personal injury or death if the
proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that
may result in minor or moderate injury if proper practices are
not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property damage, but
not personal injury.

V1.0 19.2V Cordless Grease Gun 8886442
Visit www.princessauto.com for more information 3
INTRODUCTION
The 19.2V Cordless Grease Gun has a powerful high torque motor with
6,000 PSI output grease pressure. Each of the two standard 1.5 Ah Ni-Cd
battery packs included with this grease gun will provide power to dispense
up to six grease cartridges.
SAFETY
WARNING! Read and understand all instructions before using this
tool. The operator must follow basic precautions to reduce the
risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean,
well-lit and free of distractions. Place lights so you are not working
in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store tools properly in a safe and dry location. Keep tools out of
the reach of children.
4. Do not install or use in the presence of flammable gases, dust or
liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National
Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply
with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. Wear gloves that provide protection based on the work materials or
to reduce the effects of tool vibration.
3. Wear protective clothing designed for the work environment and tool.
4. Non-skid footwear is recommended to maintain footing and
balance in the work environment.

8886442 19.2V Cordless Grease Gun V1.0
4 For technical questions call 1-800-665-8685
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with
the moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating the tool. Proper footing and
balance enables better control in unexpected situations.
4. Securely hold this tool using both hands. Using a tool with only one
hand can result in loss of control.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to the tool safety
rules. If you use this tool unsafely or incorrectly, you can suffer
serious personal injury.
CAUTION! Do not try to adjust or remove the pressure valve. It
has been set to 6,000 PSI. Adjusting or removing the pressure
valve can cause injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for an
unintended purpose.
1.1 Do not use grease gun hose for other applications or at
pressure levels above rated pressures.
2. Do not use the tool if any parts are damaged, broken or misplaced.
Repair or replace the parts.
3. If there is leakage from the pressure valve while using the gun, it
indicates that the back pressure is more than 6,000 PSI. It is not a
product failure. It is an indication that the gun is not to be used for
this application.
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment if grease
penetrates your skin. It may feel like a pricking or sting. Do not wait
for the appearance of symptoms. A toxic reaction can occur from
the exposure. Delay in treatment can lead to amputation or death.

V1.0 19.2V Cordless Grease Gun 8886442
Visit www.princessauto.com for more information 5
Inform the medical staff that you have a grease penetration injury as
soon as you arrive at the medical facility. The severity of the symptoms
will depend on the type of grease injected. Bring the Safety Data Sheet
for the grease with you to the medical facility if possible.
INJECTION PRECAUTIONS
Grease can penetrate the skin at 100 PSI pressure. Grease escaping
under pressure from the tool has sufficient force to penetrate your clothing
and skin. Follow the precautions below to avoid an injection injury.
1. Always check for leaks wearing a face shield, safety goggles,
rubberized gloves and protective clothes.
2. Release all pressure from the system before you inspect it.
3. Do not use your hands to detect a fluid leak. Use a large piece of
wood, cardboard or paper and watch for discolouration.
4. Replace damaged parts with identical manufacturer's components
to ensure it is rated to handle the pressure.
BATTERY PRECAUTIONS
WARNING! Do not charge a damaged or frozen battery. Internal
damage may allow the battery contents to leak, creating a
hazardous spill. Contact your local municipality for proper
disposal procedures.
WARNING! Only charge a battery with a charger designed for that
purpose. Do not use modified chargers or a charger that does
not specify the voltage, amperage or recharge rate. Improper
charging can lead to the battery rupturing.
1. Do not expose the battery to heat or throw it in a fire. Keep any ignition
source, such as flames, sparks or embers away from the battery.The
contents are flammable and the battery may explode. Do not inhale
smoke issuing from the burning battery as it is toxic.
2. Do not disassemble or crush the battery as the contents are
corrosive and flammable. Exposure may cause an injury.
3. Tools with internal rechargeable batteries or removable battery
packs are designed to be used only with that battery configuration.
Do not mix different battery pack brands or use adapters to allow
the use of a battery pack with a different voltage. This can damage
the tool’s electrical mechanism and create a fire hazard.

8886442 19.2V Cordless Grease Gun V1.0
6 For technical questions call 1-800-665-8685
CHARGER SAFETY PRECAUTIONS
WARNING! Voltage is present at the charging terminals, do not
probe with conductive objects. Electric shock or electrocution
may result. A battery short can cause a large current flow,
overheating, possible burns and even a breakdown of the tool.
Before using the charger, read all instructions and cautionary markings
on the charger, battery pack and the product using the battery pack.
The term battery in this precaution includes an individual battery, a
battery pack and the internal battery of a tool.
1. Only use the included battery charger to recharge the battery.
Other chargers may be unsafe, causing an electrical short circuit
or fire.
2. Disconnect the charger from its power source before attaching or
removing batteries.
3. Charge the battery in a well-ventilated area and never obstruct the
vents in the top and bottom of the charger. Place the charger on a
flat non-flammable surface and away from flammable materials
when re-charging the battery.
4. Do not place any object on top of the charger or place the charger
on a soft surface that may result in excessive internal heat. Place
the charger in a position away from any heat source.
5. Charge the battery at rates recommended by the battery
manufacturer.
6. Do not use the charger with an extension cord. This can cause a
low voltage outage during charging.
7. Do not charge leaking batteries. A compromised casing will release
volatile chemicals and gases. Charging a leaking battery can
cause a fire or explosion.
8. Do not operate the charger if it has received a sharp blow, been
dropped or otherwise damaged in any way. Have it serviced or
replaced.
9. Do not disassemble the charger or battery. Take it to an electrician
or power tool repairer when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution or fire.

V1.0 19.2V Cordless Grease Gun 8886442
Visit www.princessauto.com for more information 7
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace
the missing part before operating. Failure to do so could result in
a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage. Make sure that all items in the contents are included.
Contents:
• Blow moulded case • Battery powered grease gun
• Flexible hose • Pressure valve • Shoulder strap
• Battery charger • NI CD 19.2V battery packs (2)
IDENTIFICATION KEY
A Pipe
B Head Unit
C Barrel
D End Cap
E Coupler
F Plunger Rod Handle
G Pressure Valve
H Bulk Loader
I Trigger
J Grip
K Battery
L Battery Release
ASSEMBLY & INSTALLATION
CHARGING THE BATTERY PACK
NOTICE! Battery temperature will increase during and shortly
after use. Allow the battery pack to cool to room temperature
before charging otherwise batteries may not accept a full charge.
NOTICE! Do not recharge the new battery unless it is completely
depleted. All new guns come with an 80% charge from the
factory. No charging is needed until it is used and the battery is
run down completely.
Fig.
1

8886442 19.2V Cordless Grease Gun V1.0
8 For technical questions call 1-800-665-8685
NOTICE! Recharging the battery pack before it is depleted will
reduce the total work life of the pack. Tool performance drops
when the battery is ready to be recharged.
1. Once the battery is fully depleted, remove it from the grease gun by
depressing the battery release buttons on each side of battery
pack. Then, pull the battery pack out of gun.
2. Insert the battery pack into the charging socket of the charger, then
plug the charger into the nearest grounded, electrical outlet.
3. Press the ‘Set’ button on the charger. A green light indicates that
the battery is charging.
4. The battery will be completed charged approximately 1-2 hours
later. When charging is complete, pull the charger out of the socket
and remove the battery.
CARTRIDGE LOADING
1. Pull the plunger rod fully backward and latch the plunger rod
groove into the slot on the end cap of the grease barrel.
2. Unscrew the grease barrel from the gun head by rotating counter-
clockwise.
3. Carefully release the plunger handle to eject the empty cartridge
from grease barrel.
4. Remove the plastic cap from the grease cartridge and insert the
cartridge into the grease barrel.
5. Remove the pull tab from grease cartridge and screw grease barrel
into the gun head.
6. Prime the grease gun by following the steps in the section Priming
the Grease Gun below.
BULK LOADING
1. Unscrew the grease gun head from the barrel counterclockwise.
2. Pull back the plunger rod handle all the way.
3. Scoop out clean grease from the bulk grease container into the
empty barrel.
4. Once the barrel is full, shake it to allow the grease to settle. If
additional space is created in the barrel, add more grease to fill it
completely.

V1.0 19.2V Cordless Grease Gun 8886442
Visit www.princessauto.com for more information 9
5. Screw the grease gun head onto the barrel stopping 2-3 turns
before the head is fully tight.
6. Prime the grease gun by following the steps in the section Priming
the Grease Gun below.
7. Connect the grease gun pipe and coupler onto the grease gun
outlet using a thread sealant to make a seal-proof connection. DO
NOT over tighten as this may fracture the outlet.
SUCTION LOADING
1. Unscrew the grease gun head from the barrel counter-clockwise.
2. Insert the open end of the barrel about 2 inches into the grease
container.
3. Slowly pull back the plunger handle to draw grease into the empty
barrel while pushing the grease barrel deeper into the grease until
the plunger rod is fully extended. This will help prevent air pockets.
4. Wipe extra grease off of the outside of the grease gun. Shake the
gun to allow the grease to settle.
5. Tightly screw the grease gun head onto the barrel
6. Prime the grease gun by following the steps in the section Priming
the Grease Gun below.
TRANSFER PUMP LOADING
1. Wipe the grease gun’s bulk loader valve clean of grease and
possible debris.
2. Activate the transfer pump until a small amount of grease comes
out to minimize the transfer of trapped air.
3. Rotate the plunger handle to engage the plunger rod with the
follower. Connect the bulk loader valve tightly on the grease gun to
the loader adapter on the transfer pump line.
4. Start operating the transfer pump, keeping your hand on the grease
gun, lightly pushing it down onto the transfer pump.
5. The barrel is full when it becomes difficult to pump and the follower
rod will be extended approximately 8 inches exposing the plunger
rod groove. Stop at this time.
6. Disconnect the Bulk Loader Valve from the transfer pump line.
7. Prime the grease gun by following the steps in the section Priming
the Grease Gun below.

8886442 19.2V Cordless Grease Gun V1.0
10 For technical questions call 1-800-665-8685
OPERATION
BEFORE USE
1. Examine grease gun for misalignment, damage, noise or binding of
moving parts; leaking battery pack; or damaged hose prior to use.
Install the battery pack.
2. Check that a used cartridge has not been left in the barrel before
attempting to refill the gun. Compress the spring by pulling the
plunger handle fully outward and latch the plunger rod in the slot
on the end cap. Remove the grease gun head by turning it counter-
clockwise to remove the empty cartridge.
3. Before pushing the plunger rod into the barrel, release it from the
slot in the end cap that holds the rod fully extended and allow it to
slide forward.
4. Load the grease gun with a cartridge, bulk loading or transfer
pump loading using the detailed instructions for each under
Assembly/Installation above.
5. Remove air pockets from grease by priming the gun. Follow the
steps in the section below called Priming the Grease Gun.
PRIMING THE GREASE GUN
1. After cartridge or bulk loading the grease gun, carefully release the
plunger handle from the slot in the end cap. (In case of filler pump
loading, the plunger rod is already free from the slot.)
2. Rotate the plunger handle to engage the plunger rod with the
follower. Move plunger rod back and forth into the grease barrel to
force out trapped air.
3. Disengage the plunger rod from the follower by rotating the plunger
handle. Push the plunger rod into the grease barrel.
4. Wipe the automatic air bleeder to remove any external grease.
5. Press the grease gun switch until the gun starts dispensing grease.
DURING USE
1. Start operating the grease gun. Grease will begin to flow out from
the coupler.
2. Keep running the gun until a bubble free clear stream of grease
flows out.

V1.0 19.2V Cordless Grease Gun 8886442
Visit www.princessauto.com for more information 11
3. If air bubbles continue to appear in the grease, follow the steps in
the section above called Priming the Grease Gun until the grease
flows free of air pockets.
GREASING A GREASE FITTING
1. The tool’s grease coupler (A) has a jaw-type construction. The
coupler jaws will snap on to a grease fitting and maintain a tight fit.
2. To connect the coupler to the grease fitting, press the coupler
straight onto the grease fitting to form a snug fit (Fig. 2-1) .
3. Start operating the grease gun with
the coupler as square to the grease
fitting as possible.
4. Once greasing is completed, slightly
tilt the coupler, twist and pull back
(Fig. 2-2). The tilt and twist action will
allow easy removal of the coupler
from the grease fitting.
CARE & MAINTENANCE
CAUTION! Ensure the switch is OFF, the battery is removed from
the grease gun and the charger is unplugged before performing
any maintenance. Failure to do so can cause personal injury.
1. Maintain the tool with care. A tool in good condition is efficient,
easier to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace
damaged or worn components. Only use identical replacement
parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool clean, dry and free from oil/grease at all times.
5.1 Do not use solvents to clean the grease gun.
6. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the
tool. An improperly repaired tool may present a hazard to the
user and/or others.
Fig. 2

8886442 19.2V Cordless Grease Gun V1.0
12 For technical questions call 1-800-665-8685
BATTERY STORAGE
1. Prevent a build-up of explosive gases by storing the battery in a
ventilated area or container that will disperse the small amounts of
gas created.
2. Do not store batteries in containers / spaces with loose metal
objects. Battery terminals could be short circuited if they come into
contact with metal objects. In addition to damaging the battery, you
increase the risk of a fire.
3. Store the battery in a location that will not exceed 122°F (50°C)
and out of direct sunlight.
CLEANING - CHARGER
To reduce risk of electric shock, unplug the charger from the outlet
before attempting any cleaning. Removing the battery pack will not
reduce this risk.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.

V1.0 19.2V Cordless Grease Gun 8886442
Visit www.princessauto.com for more information 13
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not
function properly or parts are missing. If unable to do so, have a
qualified technician service the tool.
PROBLEM(S)
POSSIBLE CAUSE(S)
SUGGESTED SOLUTION(S)
Gun pumps little or
no grease.
1. Trapped air
pockets in
grease.
2. Thick or frozen
grease.
3. Blocked grease
gun extension.
4. Blocked grease
gun head.
1. Prime grease gun.
2. Use a lower viscosity
grease or add some oil to
grease to make it more
viscous or heat the gun
barrel to unfreeze the
grease.
3. Remove the extension and
operate the grease gun. If
the gun dispenses grease
then the gun is fine and you
need to either clean the
extension or replace it.
4. Disassemble the grease
gun head to check for any
contaminants or blockages.
Clean and reassemble the
grease gun head.
Excessive grease
leaking from the back
of the gun around the
plunger rod.
Damaged grease
gun rubber follower.
Replace the follower.
Grease leaks from the
connection between
the Grease Gun Head
and the Extension /
Extension and
Coupler.
Loose connection. Tighten the connection using a
thread sealant.
Grease leaks from the
coupler body joint or
from in-between the
coupler jaws and
grease nipple.
Damaged grease
coupler.
Change coupler.

8886442 19.2V Cordless Grease Gun V1.0
14 For technical questions call 1-800-665-8685
PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)
Grease is leaking
from the pressure
release valve.
1. Back pressure
more than 6,000
PSI.
1. Do not use the grease gun
for this application.
Grease gun does not
work.
1. Battery is not
charged.
2. Battery is not
installed properly.
1. Charge the battery
completely.
2. Remove the battery and
reinstall.
Battery does not
charge.
1. Battery charger is
not connected to
a power source.
2.
Battery is not fixed
properly in the
charger.
1. Connect battery charger to a
power source.
2. Remove the battery and
replace in the charger
correctly.

V1.0 19.2V Cordless Grease Gun 8886442
Visit www.princessauto.com for more information 15

8886442 19.2V Cordless Grease Gun V1.0
16 For technical questions call 1-800-665-8685

V1,0 8886442
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce
manuel afin de pouvoir le consulter plus tard.
PISTOLET GRAISSEUR

19,2 V C.A.

8886442 Pistolet graisseur sans fil de 19,2 V V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Tension nominale 19,2 V c.a.
Capacité de pile 1,5 Ah
Tension d’entrée de chargeur
120 V c.a.
Pression d’utilisation max. 6 000 lb/po carré (413 BAR)
Grease Reservoir Capacity 14 oz (400 gms)
Sortie 3 oz/minute (85 gms/min.)
Type de tuyau Flexible
Longueur de tuyau 30 po
Matériau de tube Acier
Purge d’air automatique Oui
Méthode de remplissage Recharge par cartouche / Chargement en
vrac / Recharge par pompe de
remplissage / Remplissage par aspiration
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans
ce manuel. Un avis est une alerte indiquant qu'il existe un risque de
dommage à la propriété, de blessure ou de décès si on ne respecte pas
certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou
même la mort si on omet de prendre les précautions
nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement
dangereuse qui peut entraîner des blessures
mineures ou modérées si on ne procède pas de la
façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui entraînera des dommages au
niveau de l'équipement ou des biens, mais non des
blessures corporelles.

V1,0 Pistolet graisseur sans fil de 19,2 V 8886442
Visitez www.princessauto.com pour plus d'informations 3
INTRODUCTION
Le pistolet graisseur sans fil de 19,2 V est muni d’un puissant moteur à
couple élevé appliquant une pression de sortie de graisse de 6 000
lb/po carré. Chacun des deux blocs-batteries Ni-Cd de 1,5 Ah compris
avec ce pistolet graisseur permet de dispenser jusqu’à six cartouches
de graisse.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire
le risque de blessure ou de dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et
d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre
aire de travail propre, bien éclairée et exempte de toute distraction.
Placez les lampes de façon à ne pas travailler dans l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec.
Gardez les outils hors de la portée des enfants.
4. N'installez pas et n'utilisez pas d'outils électriques en présence de
gaz, de poussière ou de liquides inflammables.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une
protection frontale et latérale pour les yeux. L'équipement de
protection des yeux devrait être conforme à la norme CSA Z94.3-
07 ou ANSI Z87.1 fonction du type de travail effectué.

8886442 Pistolet graisseur sans fil de 19,2 V V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
2. Portez des gants qui protègent en fonction des matériaux de travail
et pour réduire les effets des vibrations de l'outil.
3. Portez des vêtements de protection conçus pour l'environnement
de travail et pour l'outil.
4. Les chaussures antidérapantes sont recommandées pour maintenir
la stabilité et l'équilibre au sein de l'environnement de travail.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement
de travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre
dans les pièces mobiles d'un outil. Gardez les cheveux longs
recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en
servir. Une stabilité et un équilibre appropriés sont nécessaires afin
d'avoir un meilleur contrôle en cas de situations inattendues.
4. Tenez cet outil solidement à l’aide des deux mains. Un outil tenu
d’une seule main peut causer une perte de contrôle.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT ! Ne permettez PAS au confort ou à votre
familiarisation avec l'outil (obtenus après un emploi répété) de
se substituer à une adhésion stricte aux règles de sécurité de
l'outil. Si vous utilisez cet outil de façon dangereuse ou
incorrecte, vous pouvez subir des blessures corporelles graves.
ATTENTION! N’essayez pas d’ajuster ni de retirer la soupape de
pression. Elle a été réglée à 6 000 lb/po carré. Tout ajustement
ou retrait de la soupape de pression peut causer des blessures.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu
pour une utilisation spécifique. Évitez de modifier ou d'altérer cet outil
ou de l'utiliser à une fin autre que celle pour laquelle il a été conçu.
1.1 N’utilisez pas le tuyau du pistolet graisseur pour d’autres
applications ou à des niveaux de pression supérieurs à la
pression nominale.