Protech Se-8300 User manual

USER

MANUAL

SE-8300

Intel®ATOMTM E3845 Rich I/O

and Fanless Embedded PC

with

DVI-D / VGA/ 4COM/

2LAN/ 4USB

SE-8300 M1

SE-8300

Intel®ATOMTM E3845 Rich I/O and

Fanless Embedded PC with

DVI-D /

VGA/ 4COM/ 2LAN/ 4USB

All trademarks and registered trademarks mentioned herein are the property of their

respective owners.

This manual is copyrighted in Nov. 2015. You may not reproduce or transmit in any

form or by any means, electronic, or mechanical, including photocopying and

recording.

DISCLAIMER

This user’s manual is meant to assist you in installing and setting up the system. The

information contained in this document is subject to change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment not expressly

approve by the party responsible for compliance could void your authority to operate

such equipment.

CAUTION: Danger of explosion may occur when the battery

is incorrectly replaced. Replace the battery only with the

same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s

instructions.

WARNING: Some internal parts of the system may have

high electrical voltage. We strongly recommend that only

qualified engineers are allowed to open and disassemble

the system.

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual….......................................................

1-2

1-2 System Illustration…........................................................

1-3

1-3 System Specifications…....................................................

1-6

1-4 Power Management Firmware Specification….................

1-8

1-5 Safety Precautions….........................................................

1-10

CHAPTER 2 SYSTEM CONFIGURATION

2-1 Jumper & Connector Quick Reference Table…................

2-2

2-2 Component Locations…....................................................

2-4

2-3 How to Set Jumpers….......................................................

2-6

2-4 RS232/422/485 (COM1) Selection…..………………….

2-8

2-5 RS232/422/485 (COM2) Selection ..................................

2-9

2-6 COM3 Port RI & Voltage Selection ……….…................

2-10

2-7 COM4 Port RI & Voltage Selection ….............................

2-11

2-8 SATA(JSATA1) / mSATA(MSATA_1)Selection…..…..

2-12

2-9 Power Management Voltage Selection………………….

2-13

2-10 Ignition Mode / PC Mode Selection…………..................

2-14

2-11 Clear CMOS Data Selection……………………..............

2-15

2-12 HW AT/ATX Mode Selection…......................................

2-16

2-13 COM Port Connector…………........................................

2-17

2-14 DIO Connector………………..........................................

2-20

2-15 VGA Connector…............................................................

2-21

2-16 DVI Connector………………………………………….

2-22

2-17 Serial ATA Connector…………….………………….....

2-23

2-18 Serial ATA Power Connector……….............…………..

2-24

2-19 Universal Serial Bus Connector …………………………

2-25

2-20 LAN Connector …………………………………………

2-26

2-21 Power Button ……………………………………………

2-27

2-22 Reset Button ……………..……………………………..

2-28

2-23 Power Connector…………...............................................

2-28

2-24 CANBUS Connector….....................................................

2-29

2-25 Line-Out Connector….......................................................

2-30

2-26 MIC Connector ………….................................................

2-30

2-27 Mini-PCIe / mSATA Connector .………………………..

2-31

2-28 DC-Out Connector ………………………………………

2-35

2-29 Small 4-Pin Connector…………………………………..

2-35

2-30 Battery Connector……………………………………….

2-35

Contents

2-31 LED Connector……………………………………….....

2-36

2-32 Display Port Connector …………………………………

2-36

2-33 SR-8300 Jumper & Connector Quick Reference Table …

2-37

2-34 SR-8300 Component Locations…………………………

2-38

2-35 LTC3862EFE Phase Mode Selection……………………

2-40

2-36 LTC3862EFE Blank Time Selection…………………….

2-40

2-37 LTC3862EFE Slope Selection…………………………..

2-41

2-38 LTC3862EFE DMAX Selection ………………………..

2-41

2-39 LTC3862EFE Run Control Input Selection …………..

2-42

2-40 LTC3862EFE Main Supply Input Selection…………….

2-42

2-41 LTC4271IUF Midspan Mode Input Selection …………..

2-43

2-42 LTC4271IUF Auto Mode Input Selection……………….

2-43

2-43 PoE Connectors…………………………………………

2-44

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction.......................................................................

3-2

3-2 Intel®Trusted Execution Engine Components Utility…..

3-5

3-3 Intel®Chipset Software Installation Utility……………...

3-6

3-4 Intel®USB3.0 Extensible Host Controller Utility…........

3-7

3-5 VGA Driver Utility….......................................................

3-8

3-6 LAN Driver Utility….......................................................

3-9

3-7 Sound Driver Utility….....................................................

3-10

CHAPTER 4 AMI BIOS SETUP

4-1 Introduction…...................................................................

4-2

4-2 Entering Setup…...............................................................

4-3

4-3 Main………......................................................................

4-5

4-4 Advanced……………………….........................….........

4-6

4-5 Chipset………………......................................................

4-29

4-6 Security…..………………................................................

4-38

4-7 Boot………………………………………………………

4-39

4-8 Save & Exit………………………………………………

4-42

APPENDIX A SYSTEM ASSEMBLY

Exploded Diagram for SE-8300 Heat Sink...................................

A-2

Exploded Diagram for SE-8300 Heat Sink Block………………

A-3

Exploded Diagram for SE-8300 Thermal Pad ……………….....

A-4

Exploded Diagram for SE-8300 M/B Module (with PoE Board)

A-5

Exploded Diagram for SE-8300 M/B Module (without PoE