protech ProX-1695 User manual

USER’S
MANUAL
DualSocket370Processor
EmbeddedCard
W/ VGA / Dual LAN
ProX-1695

Copyright Notice
ProX-1695 Dual Socket 370 CPU Card
With VGA/Dual LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
notice.
This manual is copyrighted August 15, 2001. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the property
of their respective owners.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual ....................................................... 1-2
1-2 System Specification ..................................................... 1-3
1-3 Safety Precautions ......................................................... 1-6
CHAPTER 2 HARDWARE CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ................ 2-2
2-2 Component Locations ................................................... 2-3
2-3 How to Set the Jumpers ................................................. 2-4
2-4 COM Port Connector ...........…..................................... 2-6
2-5 RS232/422/485 (COM2) Selection ............................... 2-7
2-6 Solid-State Disk Socket ..................................………... 2-8
2-7 SSD Memory Mapping Selection .................................. 2-9
2-8 Keyboard or PS/2 Mouse Connector .....................….... 2-10
2-9 Keyboard or PS/2 Mouse Selection .......................….... 2-10
2-10 External Keyboard Connector ....................................... 2-11
2-11 Reset Connector ............................................................ 2-11
2-12 Hard Disk Drive LED Connector .................................. 2-11
2-13 CPU Fan Connector ...................................................... 2-12
2-14 External Speaker Connector .......................................... 2-12
2-15 VGA CRT Connector .................................................... 2-13
2-16 Hard Disk Drive Connector ........................................... 2-14
2-17 Floppy Disk Drive Connector ....................................... 2-16
2-18 DFP Connector ……….................................................. 2-17
2-19 LVDS Connector ……………………………………... 2-18
2-20 Printer Connector .......................................................... 2-19
2-21 Power LED & Keylock Connector ................................ 2-19
2-22 Green Function Connector ............................................ 2-20
2-23 Universal Serial Bus Connector .................................... 2-20
2-24 IRDA Connector ……………………………………… 2-21
2-25 Reset/NMI/Clear Watchdog …..……………………… 2-21
2-26 LAN Connector ............................................................. 2-22
2-27 Memory Installation ...................................................... 2-24
2-28 PPCI Connector ………………………………………. 2-25

Contents
2-29 CPU Type Selection ………………………………… 2-26
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction …………................................................... 3-2
3-2 VGA Driver Utility …………………………………… 3-2
3-3 Flash BIOS Update ....................................................... 3-3
3-4 LAN Driver Utility …................................................... 3-5
3-5 Watchdog Timer Configuration .................................... 3-6
CHAPTER 4 GREEN PC FUNCTION
4-1 Power Saving Block Diagram ....................................... 4-2
4-2 CPU Doze Mode ........................................................... 4-2
4-3 System Standby Mode ................................................... 4-2
4-4 System Suspend Mode .................................................. 4-3
CHAPTER 5 AWARD BIOS SETUP
5-1 Introduction ................................................................... 5-2
5-2 Entering Setup ............................................................... 5-3
5-3 The Standard CMOS Setup ………............................... 5-4
5-4 The BIOS Features Setup .............................................. 5-8
5-5 Chipset Features Setup .................................................. 5-12
5-6 Power Management Setup ............................................. 5-16
5-7 PNP/PCI Configuration ................................................. 5-19
5-8 Load BIOS Defaults ...................................................... 5-21
5-9 Load Setup Defaults ...................................................... 5-21
5-10 Integrated Peripherals .................................................... 5-22
5-11 Password Setting ........................................................... 5-24
5-12 IDE HDD Auto Detection ............................................. 5-26
5-13 Save & Exit Setup ......................................................... 5-27
APPENDIX A EXPANSION BUS
ISA Bus Pin Assignment .......................................................... A-2
PCI Bus Pin Assignment .......................................................... A-3

Contents
APPENDIX B TECHNICAL SUMMARY
Block Diagram .......................................................................... B-2
Interrupt Map ............................................................................ B-3
RTC & CMOS RAM Map ........................................................ B-4
Timer & DMA Channels Map .................................................. B-5
I/O & Memory Map ................................................................. B-6
APPENDIX C TROUBLE SHOOTING
Trouble Shooting for Error Messages ...................................... C-2
Trouble Shooting for POST Codes ........................................... C-4

Page:1-1
INTRODUCTION
This chapter gives you the information for Prox-1695. It also
outlines the System specification.
Section includes:
zAbout This Manual
zSystem Specifications
zSafety precautions
Experienced users can skip to chapter 2 on page 2-1
for Quick Start.
CHAPTER
1

Chapter 1 Introduction
Page: 1-2 Prox-1695 USER
′
S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our Prox-1695 Socket 370 Embedded Card with
VGA / LAN, which is fully PC / AT compatible. Prox-1695 provides faster
processing speed, greater expandability and can handle more task than before.
This manual is designed to assist you how to install and set up the system. It
contains five chapters. The user can apply this manual for configuration
according to the following chapters :
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specification for this system. Final part of this chapter will indicate you how to
avoid damaging this Embedded Card.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the end
of this chapter, you will learn how to set jumper and how to configure this card
to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the VGA
utility, LAN utility and Flash BIOS. It also describes the Watchdog timer
configuration.
Chapter 4 Green PC Function
This chapter explains the Green PC functions concisely.
Chapter 5 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for ISA Bus, and PCI Bus.
Appendix B Technical Summary
This section gives you the information about the Technical maps.
Appendix C Trouble Shooting
This section outlines the error messages and offers you the methods to solve
the problems.

Chapter 1 Introduction
Prox-1695 USER
′
S MANUAL Page: 1-3
1-2. SYSTEM SPECIFICATION
zCPU :
Intel® Celeron™ processors in 370-pin socket.
300A/333/366/400/433/466/500/533/566/600/667/700/733 MHz.
Dual Intel® Pentium® III processors in 370-pin socket.
500E/550E/600E/650/700/750/800/850 MHz.
Auto detect voltage regulator.
zMEMORY :
Up to 768MB SDRAM
Three 168-pin DIMMs socket on board.
zCACHE :
Depended on CPU (128/256KB Cache).
zREAL-TIME CLOCK / CALENDAR :
CMOS data back up from BIOS set or BIOS default.
Dallas DS 12887 Real Time Clock.
zBIOS :
Award Flash BIOS for plug & play function.
Easy update 256KB flash EEPROM.
Support Green Function.
Support S/IO Setup.
zKEYBOARD/MOUSE CONNECTOR :
Mini DIN connector for Keyboard or PS/2 Mouse by jumper selection.
One 5-pin External keyboard connector.
zUNIVERSAL SERIAL BUS :
Universal Serial Bus Connector on board, supports up to 2 USB ports.
zBUS SUPPORT :
External ISA/PCI BUS; PICMG Spec.
Internal PCI Bus for IDE, PPCI, & LAN.
Internal AGP Bus for VGA.

Chapter 1 Introduction
Page: 1-4 Prox-1695 USER
′
S MANUAL
zDISPLAY :
Support SVGA for CRT, LVDS, & Panel Link.
Support 32bits PCI Local Bus.
VGA BIOS combines in 256KB flash ROM together with system BIOS.
Support 15-pin connector 1600 x 1200 (64K color) resolutions on Monitor.
Integrated 8MB of SGRAM for graphic/video frame memory.
Panel Display can support PanelLink and LVDS.
Support simultaneous display of CRT & LCD panel.
zWATCHDOG :
I / O port 0443H to Enable watchdog.
I / O port 0441H to Disable watchdog.
Time-out timing select 0 / 8 / 16 / 24 / 32 / 40 / 48 / 56 / 64 / 72 / 80 / 88 / 96 /
104 / 112 / 120 sec +/- 25%.
zIDE INTERFACE :
Two IDE ports, Support up to four Enhanced IDE devices.
zFLOPPY DISK DRIVER INTERFACE :
Support up to two Floppy Disk Drives, 3.5" and 5.25" (360K / 720K / 1.2M /
1.44M / 2.88M / LS-120).
zDISK-ON-CHIPS SOCKET :
Supports up to 144MB.
zLAN INTERFACE :
Intel 82559 Fast Ethernet.
Dual LAN, support for 10BaseT/100 BaseTx PCI Bus.
Two RJ-45 Jack on board.
zSERIAL PORT :
Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs. COM1 for RS232; COM2 for RS232/422/485.
MIDI Compatible.
Programmable Baud Rate Generator.

Chapter 1 Introduction
Prox-1695 USER
′
S MANUAL Page: 1-5
zPARALLEL PORT :
SPP, ECP, EPP Function.
Bi-directional parallel port.
zGREEN FUNCTION :
Software supported by BIOS setup.
Hardware supported by switch control.
zHARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU Temperature and Cooling Fan.
zLED INDICATOR :
System power.
Hard Disk access.
LAN LED indicator.
zBUS SPEED :
ISA Bus 8MHz
PCI Bus 33MHz
PPCI Bus 33MHz
USB 12Mbit/sec
zDMA CONTROLLER :
82C37 x 2
zDMA CHANNELS :
7
zINTERRUPT CONTROLLERS :
82C59 x 2
zINTERRUPT LEVELS :
15
zOPERATING TEMPERATURE :
0 to 60°C.

Chapter 1 Introduction
Page: 1-6 Prox-1695 USER
′
S MANUAL
zSYSTEM POWER REQUIREMENT :
DC Voltage: +5V, minimum +4.75V, maximum +5.25V.
DC Ampere: 15A.
DC Voltage: +12V, minimum +11.4V, maximum +12.6V.
DC Ampere: 500mA.
zBOARD DIMENSION :
338.5mm x 122mm
zBOARD NET WEIGHT :
0.35 Kg.
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Avoid your system from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.

Page 2-1
HARDWARE
CONFIGURATION
** QUICK START **
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
zJumper & Connector Quick Reference Table
zComponent Locations
zConfiguration and Jumper settings
zConnector’s Pin Assignments
CHAPTER
2

Chapter 2 Hardware Configuration
Page: 2-2 Prox-1695 USER’S MANUAL
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Port Connector ....................….................... COM1, COM2
RS232/422/485 (COM2) Selection ....................... JP4
Solid-State Disk Socket ...............…..................... SSD
SSD Memory Mapping Selection .......................... JP7, JP9
Keyboard or PS/2 Mouse Connector ..................... DIN
Keyboard or PS/2 Mouse Selection ....................... JP10
External Keyboard Connector ............................... EXKB
Reset Connector .........................…...................... RST
Hard Disk Drive LED Connector .......................... HDL
CPU Fan Connector ..................…....................… CPUFAN1
……………………………... CPUFAN2
External Speaker Connector ....….......................... SPK
VGA CRT Connector .....................….................. VGA
Hard Disk Drive Connector .................….............. IDE1, IDE2
Floppy Disk Drive Connector ................…............ FDD
DFP Connector ….................................……….... TMDS
LVDS Connector ………………………………… LVDS1, LVDS2
Printer Connector ...............................….............. PRT
Power LED & Keylock Connector ...…................. KBL
Green Function Connector .................................... GRN
Universal Serial Bus Connector ............................. USB
IrDA Connector ………………………….………. IR
Reset/NMI/Clear Watchdog ……………………... JP6
LAN Connector .......................................…......... LAN1, LAN2
Memory Installation ..................................…........ DIMM1, DIMM2
……………………………... DIMM3
PPCI Connector ……………..…………………... PPCI
CPU Type Selection ………………….……………. JP14, JP15
Reserved Pin ……………………………………..
…………………………………….. JP2, JP5, JP13 JP16

Chapter 2 Hardware Configuration
Prox-1695 USER’S MANUAL Page: 2-3
2-2. COMPONENT LOCATIONS
12887
Flash
BIOS
DIMM3
VGA DIN
FDD
COM2
BUZ
SSD
DIMM1
Intel
IDE2
CPU
Socket370
JP4
Intel
CPUFAN2
LAN2
PRT
DIMM2
CPU
Socket370
440BX
PPCI
440BX
COM1
LAN1
CPUFAN1
HDL
EXKB
KBL
JP13
IDE1
RST
SPK
LVDS1
JP6
GRN
1
20
JP5
112
1
1
IR1
5
1
19
2
JP15
1
JP7
8
1
7
B30
1
5
2
3926
40
39
40
1
34
2
331
114
13
1
1
2
6
5
10
6
10
JP9
4
1
32
1
1
1
1
1
7
12
8
2
8
17
29
5
11
12910 11
15
1
10
211
1
1
610 4
56
3
2
B1
A1
A30
1
21
5
1
6
USB
65
110
TMDS
11
JP16
10
20
LVDS2
202
1
21
JP2
1
JP10
4
21
5
JP14
1
1
25
6
Prox-1695 Connector, Jumper and Component locations

Chapter 2 Hardware Configuration
Page: 2-4 Prox-1695 USER
’
S MANUAL
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of two or
three metal pins with a plastic base mounted on the card, and by using a
small plastic "cap", Also known as the jumper cap (with a metal contact inside),
you are able to connect the pins. So you can set-up your hardware
configuration by "open"or "close"pins.
The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3), You
can connect PIN1 & PIN2 to create one setting and shorting. You can either
connect PIN2 & PIN3 to create another setting. The same jumper diagrams are
applied all through this manual. The figure below shows what the manual
diagrams look and what they represent.

Chapter 2 Hardware Configuration
Prox-1695 USER
’
S MANUAL Page: 2-5
JUMPER DIAGRAMS
2 pin Jumper
looks like this
Jumper Cap
looks like this
3 pin Jumper
looks like this
Jumper Block
looks like this
JUMPER SETTINGS
Looks like this
3 pin Jumper
2-3 pin close(enabled)
Looks like this
Jumper Block
1-2 pin close(enabled)
2 pin Jumper close(enabled)
1
1
1212
1
1
Looks like this

Chapter 2 Hardware Configuration
Page: 2-6 Prox-1695 USER’S MANUAL
2-4. COM PORT CONNECTOR
Prox-1695 possesses two Communication Port namely the COM1 and COM2.
The difference between the two is that COM1 is fixed for RS-232, while
COM2 is selectable for RS-232/422/485.
COM1 : COM1 Connector
The COM1 Connector assignments are as follows :
PIN ASSIGNMENT
1 DCD
2 RX
3 TX
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
COM2 : COM2 Connector
The COM2 Connector assignments are as follows :
PIN ASSIGNMENT
RS-232 RS-422 RS-485
1 DCD TX- TX-
2 RX TX+ TX+
3 TX RX+ RX+
4 DTR RX- RX-
5 GND GND GND
6 DSR RTS- NC
7 RTS RTS+ NC
8 CTS CTS+ NC
9 RI CTS- NC
10 NC NC NC
COM 1
1
6
5
10

Chapter 2 Hardware Configuration
Prox-1695 USER
’
S MANUAL Page: 2-7
2-5. RS232/422/485 (COM2) SELECTION
JP4 : RS-232/422/485 Selection
COM1 is fixed for RS-232 function only.
COM2 is selectable for RS-232, 422, 485 function.
The jumper settings are as follows :
COM 2
Function
RS-232 RS-422 RS-485
Jumper
setting
(pin closed)
Open 1-2
5-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
1-3
4-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
Jumper
illustration
*** Manufactory default --- RS-232.

Chapter 2 Hardware Configuration
Page: 2-8 Prox-1695 USER’S MANUAL
2-6. SOLID-STATE DISK SOCKET
SSD: 32pin Disk-on-chip Socket
The pin assignments are as follows:
SSD
17
32
116
PIN ASSIGNMENT PIN ASSIGNMENT
1 NC 17 SD3
2 NC 18 SD4
3 NC 19 SD5
4 SA12 20 SD6
5 SA7 21 SD7
6 SA6 22 CE
7 SA5 23 SA10
8 SA4 24 OE
9 SA3 25 SA11
10 SA2 26 SA9
11 SA1 27 SA8
12 SA0 28 NC
13 SD0 29 NC
14 SD1 30 VCC
15 SD2 31 WE
16 GND 32 VCC

Chapter 2 Hardware Configuration
Prox-1695 USER’S MANUAL Page: 2-9
2-7. SSD MEMORY MAPPING SELECTION
JP7, JP9 : SSD Memory Mapping Selections
A 32-pin SSD socket supports Disk-on-Chip up to 144MB. This PnP Flash
ROM SSD can be install as one of user’s hard disk drive.
The SSD Memory Mapping Selections are as follows:
SSD Memory Map JUMPER SETTING
(pin closed)
JP7 JP9
JUMPER
ILLUSTRATION
D0000h-D1FFFh
3-4 1-2
D4000h-D5FFFh
3-4
3-4
D8000h-D9FFFh
5-6
1-2
DC000h-DDFFFh 5-6 3-4
E0000h-E1FFFh 7-8 1-2
*** Manufactory default --- D0000h-D1FFFh