protech Celeron EB-471LF M1 User manual

USER’S
MANUAL
EB-471LF
ULVCeleron®M
3.5”EmbeddedCard
WithVGA/SOUND/LAN
EB-471LF M1

Copyright Notice
EB-471LF Celeron® M
3.5” Embedded Card
With VGA /Sound/LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
notice.
This manual is copyrighted in April, 2006. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void
your authority to operate such equipment.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual ........................................................ 1-2
1-2 System Specification ...................................................... 1-3
1-3 Safety Precautions ......................................................... 1-5
CHAPTER 2 HARDWARE CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ................ 2-2
2-2 Component Locations .................................................... 2-3
2-3 How to Set the Jumpers ................................................. 2-4
2-4 COM Port Connector ……..…………………………... 2-6
2-5 RS232/422/485(COM2) Selection ................................ 2-7
2-6 Keyboard/ Mouse Connector ...................…………… 2-8
2-7 Reset Connector ............................................................ 2-8
2-8 Hard Disk Drive LED Connector .................................. 2-8
2-9 External Speaker Connector .......................................... 2-9
2-10 Power LED Connector ……............................................ 2-9
2-11 IrDA Connector ……………………………………… 2-9
2-12 System Fan Connector ………………………………… 2-10
2-13 VGA CRT Connector ………………………………… 2-10
2-14 Hard Disk Drive Connector ........................................... 2-11
2-15 Universal Serial Bus Connector ……………………… 2-12
2-16 LAN Connector ………………………………………. 2-12
2-17 Clear CMOS Data Selection ………………………… 2-13
2-18 Power Requirement Selection ………………………… 2-14
2-19 AT Power Connector …..…………………………….. 2-15
2-20 Inverter Connector …………………………………….. 2-15
2-21 Reset/NMI Watchdog Selection ………………………. 2-16
2-22 LVDS Connector ………………………………………. 2-17
2-23 Panel Voltage Selection ……………………………….. 2-18
2-24 Sound Connector ………………………………………. 2-19
2-25 TV-Out Connector …………………………………….. 2-19
2-26 LAN LED ……………………………………………… 2-20

Contents
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction …………..........................................…....... 3-2
3-2 VGA Driver Utility ……………………………….…… 3-2
3-3 Flash BIOS Update ..............................................…....... 3-4
3-4 LAN Driver Utility …...........................................…...... 3-6
3-5 Sound Driver Utility …………………………………… 3-7
3-6 Intel Chipset Software Installation Utility …..……..….. 3-8
3-7 USB2.0 Software Installation Utility ………………….. 3-9
3-8 Watchdog Timer Configuration ……………………….. 3-10
CHAPTER 4 AWARD BIOS SETUP
4-1 Introduction ................................................................... 4-2
4-2 Entering Setup ............................................................... 4-3
4-3 The Standard CMOS Features ………............................ 4-4
4-4 The Advanced BIOS Features ....................................... 4-8
4-5 Advanced Chipset Features ........................................... 4-10
4-6 Integrated Peripherals …............................................... 4-13
4-7 Power Management Setup ............................................. 4-17
4-8 PNP/PCI Configuration …............................................. 4-18
4-9 PC Health Status …….................................................... 4-20
4-10 Frequency Control ....................................…………...... 4-21
4-11 Load Fail-Safe Defaults ................................................. 4-22
4-12 Load Optimized Defaults .........................................…. 4-22
4-13 Password Setting ……………………………………… 4-23
4-14 Save & Exit Setup ......................................................... 4-24
4-15 Exit Without Saving ………………………………… 4-25
APPENDIX A EXPANSION BUS
PC104+ Bus Pin Assignment ..............................................…... A-2
APPENDIX B TECHNICAL SUMMARY
Block Diagram ........................................................................... B-2
Interrupt Map ............................................................................ B-3
RTC & CMOS RAM Map ........................................................ B-4
Timer & DMA Channels Map .................................................. B-5
I/O & Memory Map ...............................................…................ B-6

Page:1-1
INTRODUCTION
This chapter gives you the information for EB-471LF. It also
outlines the System specification.
Section includes:
zAbout This Manual
zSystem Specifications
zSafety precautions
Experienced users can skip to chapter 2 on page 2-1
for Quick Start.
CHAPTER
1

Chapter 1 Introduction
Page: 1-2 EB-471LF USER
′ S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our EB-471LF Celeron® M3.5” Embedded Card
enhanced with VGA /Sound/ LAN, which is fully PC / AT compatible. EB-
471LF provides faster processing speed, greater expandability and can handle
more task than before. This manual is designed to assist you how to install and
set up the system. It contains four chapters. The user can apply this manual for
configuration according to the following chapters :
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specification for this system. Final part of this chapter will indicate you how
to avoid damaging this Embedded Card.
Chapter 2 Hardware Configuration
This chapter outlines the component location and their functions. In the end of
this chapter, you will learn how to set jumper and how to configure this card
to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the VGA
utility, LAN utility, sound utility, and BIOS update. It also describes the
Watchdog timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for PC104+ Connector.
Appendix B Technical Summary
This section gives you the information about the Technical maps.

Chapter 1 Introduction
EB-471LF USER ′ S MANUAL Page: 1-3
1-2. SYSTEM SPECIFICATION
zCPU :
Intel® Celeron® M processor
Ultra Low Voltage without L2 cache onboard
Available at 600MHz
System bus frequency at 400MHz
Auto detect voltage regulator
zSYSTEM CHIPSET :
Intel® 852GM chipset
zMEMORY :
Supports up to 1 GB DDR SDRAM.
One 200-pin DDR SO-DIMM sockets on board
zCACHE :
Built-in CPU
zREAL-TIME CLOCK / CALENDAR :
256-byte battery backed CMOS RAM.
Hardware implementation to indicate century rollover
zBIOS :
Phoenix-AwardBIOS™ for plug & play function
Memory size with 4 MB, with VGA BIOS
zKEYBOARD/MOUSE CONNECTOR :
PS/2 keyboard with mini DIN connector or one external Y cable.
zUNIVERSAL SERIAL BUS :
Universal Serial Bus Connector on board
Supports up to two USB 2.0 ports.
zBUS SUPPORT :
PC/104+ Connector.

Chapter 1 Introduction
Page: 1-4 EB-471LF USER
′ S MANUAL
zDISPLAY :
Built in Intel 852GM, support CRT, LCD.
zIDE INTERFACE :
One IDE ports support up to two IDE devices.
Supports UDMA 33/66/100.
zLAN INTERFACE :
Intel® 82562ET 10/100 Base-T
zSOUND:
AC '97 Codec. Reatel ALC202A.
Fully Compliant AC '97 Analog I/O Component
zSERIAL PORT :
Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs. COM1 for RS232; COM2 for RS232/422/485.
zHARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU Temperature and Cooling Fan.
zIRDA PORT :
One 5-pin Infrared connector
Supports IrDA v1.0 SIR protocol.
zLED INDICATOR :
HDD LED, Power LED.
zDMA CONTROLLER :
82C37 x 2
zDMA CHANNELS :
7
zINTERRUPT CONTROLLERS :
82C59 x 2
zINTERRUPT LEVELS :
15

Chapter 1 Introduction
EB-471LF USER ′ S MANUAL Page: 1-5
zOPERATING TEMPERATURE :
0 to 60°C (32°F to 140°F)
zINPUT POWER REQUIREMENT :
AT power: +5V, +12V
Only +5V: +5V only provide power for SBC, It does not have enough power
to support expansion card.
zBOARD DIMENSION :
102mm x 145mm (4.02” x 5.71”)
zBOARD NET WEIGHT :
290 grams (0.64 lb)
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Avoid your system from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the card
is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance, when
you connect a jumper or install any cards, a surge of power may damage the
electronic components or the whole system.