Provision ISR ZP-20A-2(IR) User manual

1
Package Contents:
Item ZP-20A-2(IR)
Qty.
ZP-20A-2(IR)
1
Wall Bracket
1
Hinge Pin
1
Rubber Seal
1
AC power supply
1
Wall Screws
4
PM8*25 socket head screws
1
Allan Key
1
Item ZE-20A-2(IR)
Qty.
ZE-20A-2(IR)
1
Wall Bracket
1
DC power supply
1
Wall Screws
4
PM8*25 socket head screws
1
Allan Key
1

2
Table of Contents:
1 General Instructions:...................................................................3
1.1 Safety Instructions: .......................................................................... 3
1.2 Warnings: ......................................................................................... 3
2 Features: ......................................................................................4
2.1 Product Picture: ............................................................................... 4
2.2 Product Features.............................................................................. 4
2.3 Specifications: .................................................................................. 5
3 Installation Site Preparations:.....................................................7
3.1 Tool List: ........................................................................................... 7
3.2 Installation Preparation:.................................................................. 7
3.3 Output mode setting: ...................................................................... 6
3.4 Product dimension:.......................................................................... 7
4 Setup of the OSD Menu:..............................................................8
4.1 Display Boot-UP Info.......................................................................... 8
4.2 Enter the OSD Menu:....................................................................... 9
4.3 SYSTEM Menu:............................................................................... 10
4.5 Advanced Camera Menu: .............................................................. 18
APPENDIX I Shortcuts Key Chart:.................................................21
APPENDIX II Trouble Shooting: ....................................................21

3
1 General Instructions:
1.1 Safety Instructions:
◆Make sure to read the user manual before using the camera.
◆Always follow national and local safety codes during the installation.
◆Only a qualified and experienced person can carry the installation and
maintenance for this camera.
◆Use reliable tools.
◆Make sure that the environmental conditions meet the installation
requirements for this product.
◆Please check the space and toughness of the installation surface before
installation. It should be able to bear 4 times the weight of the camera
and its accessories.
1.2 Warnings:
◆Do not install this speed dome in hazardous places where combustible
or explosive materials are stored or used.
◆Do not install on a platform that suffers from constant vibrations.
◆Make sure no object or fluid substances get inside the unit.
◆ZP-20A-2(IR) runs on AC24V and ZE-20A-2(IR) runs on DC12V. Do not
connect it to a different voltage.
◆Do not turn the power on before installation is complete.
◆Do not disassemble any part of the camera.
◆Use a soft towel to clean the down the lenses when necessary, do not
use caustic detergent.
◆To protect the image sensor, avoid facing the camera directly into a
strong light.
◆To prevent damage, do not drop the unit or expose to strong shocks or
vibrations.
◆Make sure no object is blocking the unit’s full range of motion.

4
2 Features:
2.1 Product Picture:
ZP-20A-2(IR) ZE-20A-2(IR)
2.2 Product Features (Items marked with * are only available in
ZP-20A-2(IR) Pro solution)
◆Alarm I/O: 1 Input/ 1 Output*
◆CoC Support
◆4 in 1 (AHD/TVI/CVI/CVBS)
◆Adaptive PELCO-P/D protocol.
◆Memory recall.
◆Real-Time-Control: call any functions at any time.
◆Support 255 preset positions.
◆English OSD menu.
◆Proportional zoom.
◆Auto flip function.
◆Built-in lightning proof and surge proof protection.
◆Advanced step motor for smoother movement.
◆Support Tour 4 groups, 8 Auto scan, 4 patterns, and 360°continuous
scan and 360° intermittent scan.
◆The upper dome adopts 7" aluminum alloy structure for better

5
magnetic shield and heat radiation.
◆The underpart dome adopts full metal class points bin type design for
fast heat dissipation and anti-mist, non-interference light source images
and long life span IR light.
◆Integral Junction box for easy installation*
2.3 Specifications:
Model
ZP-20A-2(IR)
ZE-20A-2(IR)
Sensor
1/2.8”CMOS
Resolution
2MP- 1920*1080
Optical Zoom
X20 (4.9-97MM)
Digital Zoom
No
Minimum Focus Distance
1.5M
Horizontal Angle of View
H:57 (Wide) to 4 (Tele)
V:33.5 (Wide) to 2 (Tele)
Sync System
Internal
Min. Illumination
0.01Lux (0 Lux with IR ON)
Day & Night
Auto/Manual/Night
S/N Ratio
>50db
Focus
Auto/Manual/One-Push
Auto Gain
Auto/Manual
Wide-D
Yes
White Balance
ATW/Manual/Outdoor/Indoor/AWB/AWC
BLC
On/Off
Shutter Speed
1/ 50 ~1 / 10000
Sense Up
No
Noise Reduction
3D-DNR

6
Flip
ON/OFF
Picture Freeze
No
Iris
Auto
Power Supply
AC24V±5%, 3A
DC12V, 2A
Sync system
Internal Sync
Language
English
Signal Output
4 in 1 AHD/TVI/CVI/CVBS + PAL/NTSC
IR Distance
100 IR LED Array
Pan Speed
0.01°~350°/s
(Max. Preset
Speed)
0.01°~60°/s (Max.
Preset Speed)
Tilt Speed
0.01°~120°/s
(Max. Preset
Speed)
0.01°~30°/s (Max.
Preset Speed)
Pan Range
0°～360°(Continuous)
Tilt Range
0°～90°（180° auto flip）
Presets
255
Preset Accuracy
<±0.1°
Tour
4Groups
Pattern
4
Auto-scan
8
Protocol
CoC / RS-485
Communication
CoC / PELCO-D/P
Baud Rate
2400bps、4800bps、9600bps
Address
1-255 (Software)
Work Temperature
-20 ℃+50℃
Work Humidity
<90%
Weight
3.25Kg

7
3. Installation Site Preparations:
3.1 Tool List:
(1) Screws* (2) Monkey wrench
(3) Philips screwdriver (4) Straight Screwdriver
(5) Wire stripper (6) Socket head wrench
(7) Electric drill (8) Hammer
(9) BNC connector (10) BNC Clamp
*Included in the kit
3.2 Installation Preparation:
(1) Check the space and toughness of the site and make sure that the
environmental conditions meet the installation requirements for this product.
(2) The installation surface should be able to bear 4 times the weight of the
PTZ and its accessories.
3.3 Output Mode Setting:
(1) Default Settings: AHD, PAL system
This output can be changed via the controller (Even if the user cannot gain a
video output from the unit due to output incompatibility)
(2) Set your controller/DVR PTZ Settings to the Camera’s Default
Communication Settings: Protocol: CoC / PELCO-D, address: 1 (Unless user
changed it by the DIP switch configuration), baud rate: 2400.
(3) In order to change the output type follow the instructions below:

8
AHD/TVI/CVBS Command
Set #85 preset,
Please note: you will have to use “Save
Position” or delete and recreate the
preset if you need to use it more than
once –AS it is “set” action.
Call the preset number of
the desired video type
signal:
e.g. “14” for CVBS/NTSC
N=1
AHD
N=2
TVI
N=3
CVI
N=4
CVBS
CVI Command
Set #50 preset,
Please note: you will have to use “Save
Position” or delete and recreate the
preset if you need to use it more than
once –AS it is “set” action.
Call the preset number of
the desired video type
signal:
e.g. “14” for CVBS/NTSC
N=1
AHD
N=2
TVI
N=3
CVI
N=4
CVBS
3.4Product dimension:

9
4. Setup of the OSD Menu:
4.1 Display Boot-UP Info.
Before installation please check the protocol, baud rate, address, and RS485
data cable. Default Settings: Protocol: PELCO-D, address: 1, baud rate: 2400.
4.2 Enter the OSD Menu:
While the camera is in standby condition, call preset 95 (“Call” + 95 + “Enter”)
in order to display the main menu. Use the Up/Down direction to select the
item or start the configuration. Use the Right key to confirm and left the key
to exit the current setting.
The Main menu as follows:
INFORMATION
DOME SETTINGS
MOTION
RESTART
FACTORY DEFAULTS
EXIT
VERSION: VR210P-306
SIGNAL:AHD PAL
PROTOCOL: PELCO P D
BAUD RATE: 2400
CAMERA ID: 001
TEMP: 36
STATUS:OK

10
4.3 SYSTEM Menu:
<Main Menu> →<INFORMATION>
The user can check the dome system information as required. The
system information includes Version, dome address, baud rate,
temperature, voltage.
4.3.1 INFORMATION
INFORMATION
DOME SETTINGS
MOTION
RESTART
FACTORY DEFAULTS
EXIT
INFORMATION
VERSION: VR210P-306
ADDRESS:001
BAUDRATE:2400
TEMPERATURE:37
VOLTAGE:11.6V
BACK EXIT

11
4.3.2 DOME SETTING
4.3.2.1 IR LED
The user can open and close the IR LED manually and set up the IR LED work
mode under this OSD mean. (Under normal operation mode, the user can
press IRIS OPEN and IRIS CLOSE to adjust the IR LED power):
1) control mode:
DOME SETTING
IR LED
WIPER
PART ACTION
ALARM
PRIVACY MASK
ADVANCED
OTHER
BACK EXIT
IR LED SETTING
CONTROL MODE:AUTO
SENSITIVITY:----218
NEAR POWER:100
FAR POWER:100
COMPENSATION:0
BACK EXIT

12
2) Sensitivity:
Users can manually set the sensitivity from 1-10. The smaller the number is,
the lower light of the environment will be when the IR LED on.
3) NEAR POWER: 100
4) FAR POWER: 100
5) COMPENSATION: 0-50
4.3.2.3 Park Action
Users can set the parking time and action.
1）Time：1MIN/2MIN/3MIN
2) Action: NONE / patter1 / Tour1 / Scan1 / Preset1
AUTO
IR LED will be opened or closed automatically according to
the light conditions.
ON
IR LED forcedly open
OFF
IR LED forcedly close
CAMERA
IR LED status (Open/Close) will be synchronized with
Camera day and night switching
PARK ACTION
TIME: 1MIN
ACTION:NONE
BACK EXIT

13
4.3.2.4 ALARM (Only available for ZP-20A-2(IR)
4.3.2.5 ADVANCED
4.3.2.5.1 <ADVANCED> →<DOME SPEED SETTING>
ALARM SETTING
ALARM NO:1
CONTACT:NO
ALARM MODE:OFF
ACTION:NONE
ALARM OUT:OFF
RESET DELAY:10SEC
BACK EXIT
ADVANCED
FOCUS MODE: PUSH
FOCUS LIMIT:3M
(DOME SPEED)
(TILTANGLE)
BACK EXIT
DOME SPEED SETTING
DOME SPEED: 180
BACK EXIT

14
4.3.3 OTHERS
The user can set up TEMP MODE, INTERNAL FAN, AUTO FLIP, STOP TIME,
MENU OFF here under the menu of “OTHERS”
1)TEMP MODE: To set up the control mode of dome fans and heaters. It
includes three modes of AUTO, FAN HIGH SPEED, and FAN LOW SPEED.
2)FAN ON TEMP: To set up the temperature that Fan start work
3)AUTO FLIP: When the camera tilts downward and goes just beyond the
vertical position, the camera will rotate 180 degrees. The user can press IRIS
OPEN to enter and choose to turn on/off this function.
4)STOP TIME: To set up the time that dome will stop after receiving the last
command. Options include 5 / 15 / 30 / 60 Sec.
5)MENU OFF TIME: To set up the time that the OSD menu is off when no
operations. Options include 1 / 2 / 5 / 10 min.
OTHERS
TEMP MODE:AUTO
FAN ON TEMP:50
AUTO FLIP:ON
STOP TIME:30 SEC
MENU OFF:5MIN
DISPLAY:OFF
(AZIMUTH ZERO)
BACK EXIT

15
4.3.4MOTION
The user can set up 4 motion detection scenes under this menu.
1)PRESET: The dome supports 255 presets.
2)SCAN: The dome supports 8 groups of the auto scan.
3)Tour: The dome supports 4 groups of the cruise.
4)PATTERN: The dome supports 4 pattern tours and each pattern cover at
5)most 10 Minutes of 500 commands.
4.3.4.1 PRESET
The dome supports 255 presets. Please check the following steps to set
up a preset.
1) PRESET NO.: Move the cursor here and press IRIS OPEN to enter the
setup of Preset Number. Move the joystick to select a preset number
(1-64 and 100-255) and press IRIS OPEN to confirm.
MOTION
PRESET
SCAN
TOUR
PATTERN
BACK EXIT
PRESET
PRESET NO: 001
CALL
(SET)
DELETE
SPEED:HIGH
BACK EXIT

16
2) <SET>: Move the cursor here and press IRIS OPEN to enter. Move the
dome to a defined position as a preset point and press IRIS OPEN to save
the preset position.
3) CALL: Move the cursor here and press IRIS OPEN to call up the current
preset.
4) DELETE: Move the cursor here and press IRIS OPEN to delete the current
preset.
5) SPEED: Move the cursor here and press IRIS OPEN to set up the preset
call-up speed of LOW, MID and HIGH.
4.3.4.2 SCAN
The dome supports 8 groups of auto scan. Please check the following
steps to set up a scan.
1)SCAN NO.: Move the cursor here and press IRIS OPEN to enter the setup of
SCAN Number. Move the joystick to select a preset number (1-8) and press
IRIS OPEN to confirm.
2)TITLE: Move the cursor here and press IRIS OPEN to enter the setup of
SCAN Title. Check the detailed above in DOME TITLE settings.
3)<LEFT LIMIT>: Move the cursor here and press IRIS OPEN to enter. Move
the dome to a defined position as the left limit and press IRIS OPEN to save
SCAN
SCAN NO:001
START
(LEFT LIMIT)
(RIGHT LIMIT)
SCAN SPEED:10
BACK EXIT

17
this left boundary.
4)<RIGHT LIMIT>: Move the cursor here and press IRIS OPEN to enter. Move
the dome to a defined position as the right limit and press IRIS OPEN to save
this right boundary.
5)START: Move the cursor here and press IRIS OPEN to start the current scan.
6)SCAN SPEED: Move the cursor here and press IRIS OPEN to set up the scan
speed ranging from 1-10.
4.3.4.3 TOUR
The dome camera will run repeatedly as the given sequence of presets at
certain dwell time by one command. Max. 4 tours available (16preset/tour).
1)TOUR NO: Set the current tour number from 001~004.
2)DWELL: Set the default dwell time from 000~255 seconds for each preset.
Users can still set independent dwell time for each preset when editing the
tour.
3)EDIT: Edit presets and corresponding dwell time on a tour.
4.3.4.4 PATTERN
TOUR
TOUR NO:1
START
(TOUR SET)
BACK EXIT

18
The dome supports 4 pattern tours and each pattern cover at most 10
Minutes of 500 commands. Please check the following steps to set up a
pattern.
1) PATTERN NO.: Move the cursor here and press IRIS OPEN to enter the
setup of Pattern Number. Move the joystick to select a pattern number
(14) and press IRIS OPEN to confirm.
2) START: Move the cursor here and press IRIS OPEN to start the current
pattern tour.
3) <SET>: Move the cursor here and press IRIS OPEN to enter. Move the
dome up/down/left/right, make the zoom in/out and press IRIS OPEN to
save the pattern tour.
4) DELETE: Move the cursor here and press IRIS OPEN to delete the current
pattern tour.
4.5 Advanced Camera Menu:
For advanced Menu, Call preset #69.
PLEASE NOTE: Scrolling and changing values in the advanced menu is done
with different controls:
1) The controller joystick has no effect.
2) Scrolling up and down is done by pressing IRIS+/IRIS-
3) Changing Values of the selected feature is done by pressing
ZOOM+/ZOOM-
PATTERN
PATTERN NO:1
START
(SET)
DELETE
BACK EXIT

19
IMPORTANT!!! Changing any values the advanced menu might result in the
camera malfunctioning
⚫<OSD-DISP >: Do Not Change
⚫<ADDR-DISP>: Do Not Change
⚫<D&N>: Do Not Change
⚫<MIRROR>: Turning Mirror effect ON/OFF
⚫<AGC>: changing the value of AGC
⚫<BRIGHT>: Changing the brightness value.
⚫<CONTRAST>: Changing the contrast value.
⚫<SHARPNESS>: Changing the sharpness value.
⚫<SAT>: Changing the saturation value.
OSD-DISP ON
D&N AUTO
MIRROR OFF
AGC 15
BRIGHT 40
CONTRAST 0
SHARPNESS 5
SAT 42
WDR AUTO
2D-NR 1
3D-NR 2
BLC OFF
WB ATW
RGAIN 00
BGAIN 00