Provision ISR Z-22IR User manual

1
Package Contents:
Item Qty.
Z-2 2/2 7 IR PTZ 1
Wall Bracket 1
Hinge Pin 1
Rubber Seal 1
DC12V/5A power supply 4
Wall Screws 4
PM8*25 socket head screws 1
Allan Key 1
User Manual

2
Table of Contents:
1 General Instructions...................................................................................... 3
1.1 Safety Instructions ............................................................................ 3
1.2 Warnings........................................................................................... 3
2 Features ........................................................................................................ 4
2.2 Product Features............................................................................... 4
2.3 Specifications.................................................................................... 5
3 Installation Site Preparations ........................................................................ 6
3.1 Tool List............................................................................................. 6
3.2 Installation Preparation .................................................................... 6
3.3 DIP Switch Setup............................................................................... 7
4 Setup of the OSD Menu ................................................................................ 8
4.1 Display Boot-UP Info........................................................................... 8
4.2 Enter the OSD Menu......................................................................... 9
4.3 SYSTEM ........................................................................................... 10
4.4 LENS................................................................................................ 15
4.5 CAMERA.......................................................................................... 17
4.6 PAN/TILT ....................................................................................... 211
4.7 AUTO RUNNING.............................................................................. 22
4.8 PRIVACY MASK................................................................................ 29
4.9 ALARM.......................................................................................... 300
4.10 LANGUAGE.................................................................................. 311
4.11 IR SET .......................................................................................... 322
APPENDIX I: DIP Switch Setting...................................................................... 33
APPENDIX II Shortcuts Key Chart ............................................................... 3838
APPENDIX III Trouble Shooting..................................................................... 400

3
1 General Instructions:
1.1 Safety Instructions:
Make sure to read the user manual before using the product.
Always follow national and local safety codes during the installation.
Only qualified and experienced person can carry this installation and
maintenance.
Use reliable tools, not complying can result in serious injury.
Make sure that the environmental conditions meet the installation
requirements for this product.
Please check the space and toughness of the site before installing. It
should be able to bear 4 times the weight of the dome and its
accessories.
1.2 Warnings:
Do not install this speed dome in hazardous places where combustible
or explosive materials are stored or used.
Do not install on platform that suffers from constant vibrations.
Make sure no object or fluid substances get inside the unit.
This speed dome runs on DC 12V, do not connect it to higher or lower
voltage.
Do not turn power on before installation is complete.
Do not disassemble any part of the items.
Use soft towel to clean the down cover when necessary, do not use
caustic detergent.
To protect CCD, avoid facing the camera directly into strong light.
To prevent damage, do not drop the unit or allow to strong shocks or
vibrations.
Make sure no object is blocking the unit’s full range of motion.

4
2 Features:
2.1 Product Picture:
2.2 Product Features
Alarm I/O.
Adaptive PELCO-P/D protocol.
Adjustable IR illumination.
Memory recall.
Real-Time-Control: call any functions at any time.
Up to 8 privacy masks.
Support 128 preset positions.
English OSD menu, user friendly for smooth operation.
Proportional zoom.
Auto flip function.
Built in lightning proof and surge proof.
Advanced step motor: Less heat, Smooth movement, No-shaking.
Efficient heating device, ensure to work in -20°low temperature.
Support 4 groups cruise scan (27 presets/group), 4 group patterns, one
scan, and 360°continuous scan and 360° intermittent scan.
IR lights automatically adjust the light intensity according to the zoom

5
speed to reduce the dark angle and flashlight effect.
The upper dome adopts 7" aluminum alloy structure for better
magnetic shield and heat radiation.
The underpart dome adopts full metal class points bin type design for
fast heat dissipation and anti-mist, non-interference light source images
and long life span IR light.
2.3 Specifications:
Power Supply Input：AC100～240V 50/60Hz
Output：DC12V±5%，5A
Max. Power
Consumption
IR off：15W
IR on：31W
Sync system Internal Sync
Language English
Pan Speed 0.08°～240°/S
Tilt Speed 0.08°～240°/S
Pan Range 0°～360°(Continuous)
Tilt Range 0°～90°（180° auto flip）
Preset 128
Preset Accuracy <±0.1°
Tour 4, 27 presets/tour
Pattern 4
Zone 1
Protocol RS485
Communication PELCO-D/P auto detected
Baud Rate 2400bps、4800bps、9600bps、19200bps
Address 1-255 (By DIP Switch or Software)

6
RTC Set any functions at any time
IR Light switch
Superpower LED：Default: Zoom x1~5: open the
near-
distance IR lights; Zoom x6~9: open the
near-distance and middle-d
istance IR lights;
Zoom >x10: turn off the near-distance IR lights,
open the middle-distance and far-
distance IR
lights.
Work
Temperature
Indoor：0
℃
～+50
℃
；
Outdoor ：-20
℃
～+50
℃
(with heater)
Work Humidity <90%
3 Installation Site Preparations:
3.1 Tool List:
(1) Screws* (2) Monkey wrench
(3) Philips screwdriver (4) Straight Screwdriver
(5) Wire stripper (6) Socket head wrench
(7) Electric drill (8) Hammer
(9) BNC connector (10) BNC Clamp
*Included in the kit
3.2 Installation Preparation:
(1) Check the space and toughness of the site and make sure that the
environmental conditions meet the installation requirements for this product.
(2) The installation surface should be able to bear 4 times the weight of the
PTZ and its accessories.

7
3.3 DIP Switch Setting:
(1)Default Settings: Pelco P/D (auto-detected), baud rate: 2400, address: 1.
Use Philips screwdriver to remove the DIP switch cover (see location below)
(2)Baud Rate Setup
Decoder Switch: 9~10 (1=ON, 0=OFF)
Switch 9-10 setting
Baud Rate Max transmission
distance(M)
9 10
0 0 2400BPS 1800
1 0 4800BPS 1200
0 1 9600BPS 800
1 1
Auto detected 2400、
4800、9600、
19200BPS
600-1800
(3) When the DIP Switch 9th and 10th are ON, the PTZ can automatically
detected the baud rate 2400, 4800,9600,19200
(4) Hardware Address Setup*: Please refer to Appendix I.
*Please note that the address setting can also be configured via the
software using the camera OSD (Page 11).
DIP Switch
Position Reset Position

8
4 Setup of the OSD Menu:
4.1 Display Boot-UP Info.
Before installation please check the protocol, baud rate, address and RS485
data cable. Default protocol: PELCO-D, address: 1, baud rate: 2400.
When starting, the PTZ will display the following information:
Once done, the above information will disappear and the user will gain
control over the camera.
4.2 Enter the OSD Menu:
While the camera is in standby condition, call preset 95 (“Call” + 95 + “Enter”)
in order to display the main menu. Use the Up/Down direction to select item
or start the configuration. Use the Right key to confirm and left key for exit
the current setting.
Level self-check: Success
Vertical self-check: Success
Camera type: ####
Success
PROTOCOL: PELCO P D
BAUD RATE: 2400BPS
CAMERA ID: 001
CAMERA S/N: 0000000001
MODEL: -----------------
VERSION: V1.02
FAN SPEED: 6000RPM
STARTING… ….

9
The Main menu as follows:
4.3 SYSTEM Menu:
<Main Menu> <SYSTEM>
SITE INFO
DISPLAY SETUP
BOOTUP SCREEN
PASSWORD
SET DEFAULT
SYSTEM REBOOT
RTC TIME SET
RTC TIMER RUNNING
BACK
EXIT
SYSTEM
LENS
CAMERA
PAN/TILT
AUTO RUNNING
PRIVACY MASK
ALARM
LANGUAGE
IR SET
EXIT

10
System info includes following settings.
< SITE INFO>: In this menu the user can setup the dome’s name, View
the Hardware address, change the camera software address and choose
the leading command (Hardware or Software).
< DISPLAY SETUP >: In this menu the user can choose which details will
display on the camera Screen. The available options are: Site name,
Preset title, Pattern name, Zoom, Orientation, Temperature, Zone name
and RTC time.
<DISPLAY BOOT-UP INFO>: User can view the boot information.
<PASSWORD >: User can setup or change menu access password.
<SET DEFAULT>: All settings will go back to factory default. Preset
positions will be retained.
<SYSTEM REBOOT>: After change dome ID or adjust deviation between
two preset positions, user this to remotely reboot the system.
<RTC TIME SET>: Set the present date and time.
<RTC TIMER RUNNING>: Schedule actions for specific date and time.
4.3.1 SITE INFO
NAME: GXAAF DOME: 001
DOME ID OPT: SOFT
SOFTWARE ID: 001
HARDWARE ID: 000
BROADCAST ID: 255
BACK
EXIT

11
<Main Menu> <SYSTEM> <SITE INFO >
<NAME>: The title name of the dome. Assigning a name to a dome
helps the user to identify which dome is under control for multiple
domes site. Max 16 digits Setting with number from 0~9 and letter from
A~Z. Move the cursor to <SITE ID> and then move the joystick right to
enter dome ID setting,
<DOME ID OPT>: Setting the address method that controls the dome,
user can choose from SOFT (Software) and HARD (Hardware).
[SOFT]: when choose this, the SOFTWARE ID is effective while the
HARDWARE ID is ineffective.
[HARD]: when choose this, the HARDWARE ID is effective while the
SOFTWARE ID is ineffective.
<SOFTWARE ID>: shows the current software ID, user can modify and
choose address in the range of 001~254
<HARDWARE ID>: shows the current physical ID, it is decided by the DIP
Switch only: user cannot modify via the OSD.
<BROADCAST ID>: shows the current ID, The ID functions the same as
dome’s <SORTWARE/ HARDWARE ID>, The dome works when receives
any of those ID. The dome’s broadcast ID is 255 and cannot be
modified.
<BACK>: return to upper menu.
<EXIT>: exit the menu

12
4.3.2 DISPLAY SET UP
< Main Menu><SYSTEM><DISPLAY SETUP>
<SITE NAME>：Choose to display site name or not.
<PRESET TITLE>：Choose to display preset position or not.
<PATTERN NAME>：Choose to display pattern name or not
<ZOOM>：Choose to display the current zoom or not.
<ORIENTATION>：Choose to display the current lens direction or not.
<TEMPRETURE>：Choose to display the current temperature or not.
<ZONE NAME>：Choose to display the current zone name or not.
<RTC TIME>：Choose to display the date and time or not.
SITE NAME: OFF
PRESET TITLE: OFF
PATTERN NAME: OFF
ZOOM: OFF
ORIENATATION: OFF
TEMPRETURE: OFF
ZONE NAME: OFF
RTC TIME: OFF
BACK
EXIT

13
4.3.3 DISPLAY BOOT-UP INFO
<Main Menu><SYSTEM><DISPLAY BOOT-UP INFO>
Enter into Boot-up info displays to check current setup, call preset 1 to return
to upper menu
4.3.4 PASSWORD
<Main Menu><SYSTEM><PASSWORD>
<INPUT PASSWORD > (Factory default is 123456):
Use the joystick to enter submenu, then input the old password. If you forget
the password after changing, please contact Provision-ISR support for
recovery password.
The cursor will flash if the old password is correct, and then input the new
INPUT PASSWORD: ******
CONFIRM: ******
PSWD PROTECTION: OFF
BACK
EXIT
PROTOCOL: PELCO P D
BAUD RATE: 2400BPS
CAMERA ID: 001
CAMERA S/N: 0000000001
MODEL: -----------------
VERSION: V1.02
FAN SPEED: 6000RPM
CALL PRESET 1 TO BACK

14
password. If the old Password input is not correct, you will not be able to
change the password.
<CONFIRM>:
Re-input the new password and confirm. If the input is not the same as the
first time input, the system will remain the old password.
<PSWD PROTECTION>:
Switch on / off the password protection. When it is <On> user need to enter
password in order to access OSD menu or save preset through keyboard.
<BACK>: return to upper menu.
<EXIT>: exit the menu
4.3.5 SET DEFAULT
<Main Menu><SYSTEM><SET DEFAULT>
Select <SET DEFAULT> to restore factory default setting.
Please note: there is no confirmation prompt! Once entering the camera
will immediately restore itself.
4.3.6 SYSTEM REBOOT
<Main Menu><SYSTEM><SYSTEM REBOOT>
Select <SYSTEM REBOOT> to reboot the dome.
4.3.7 RTC TIME SET
<Main Menu><SYSTEM><RTC TIME SET>
DATE Y/M/D: 00 00 00
TIME H: M: S: 00 00 00
BACK
EXIT

15
Use left and right keys to move the cursor to desired item, use up and down
keys to change the current cursor value.
4.3.8 RTC RIME RUNNING
<Main Menu><SYSTEM><RTC TIMER RUNNING>
<DATE and TIME>: Setup time running time (24-hour)
<ACTION>: Choose one function from <PRESET>, <ZONE>, <TOUR>,
<PATTERN> to run.
<BACK>: Back to the upper menu.
<EXIT>: Exit the current menu.
4.4 LENS
<Main Menu><LENS>
DATE Y/M/D: 00 00 00
TIME H: M: S: 00 00 00
ACTION: PRESET 001
BACK
EXIT
ZOOM SPEED: HIGH
DIGITAL ZOOM: OFF
JOYSTICK AF/AI: BOTH
AF RESUME TIME: 005
AI RESUME TIME: 005
DAY/NIGHT: IR-CTR
CAMERA P/N: AUTO
BACK
EXIT

16
<ZOOM SPEED>: Set the zoom speed level to HIGH or LOW
<DIGITAL ZOOM>: Turn On/Off the Digital Zoom.
<JOYSTICK AF/AI>: Set up Auto Focus (AF), Auto Iris (AI) or Both
<BOTH>: Joystick movement triggers both auto focus and auto iris <FOCUS>：
Joystick movement triggers auto focus only
<IRIS>: Joystick movement triggers auto iris only.
<NONE>: Joystick movement triggers none of the functions.。
<AF RESUME TIME>: This item sets the time to restore auto focus after
focus is manually changed. The default setting is 005, options are:
[OFF] Never restore auto focus after switch to manual.
[001-255]The dome will start auto focus that number of seconds after user
manually adjusts focus.
<AI RESUME TIME>: This item sets the time to restore auto iris after iris
is manually changed. The default setting is 005 seconds, options are:
[OFF]: Never restore auto iris after switch to manual.
[001-255]: The dome will start auto iris that number of seconds after user
manually adjust iris.
<DAY/NIGHT>: Set the dome color/ black & white mode. Color mode is
suitable to work in daytime because it needs higher illumination. Light
sensitivity of black & white mode is much higher. It is suitable to work
at night without illumination but the video is black and white.
There are 4 options:
[AUTO]: The dome will automatically change modes according to the
environment illumination.
[COLOR]: The dome is always in color mode.
[NIGHT]: The dome is always in Black and White mode.
[IR-CTL]: The dome is controlled by the IR lights sensor, when the IR lights
opened, the mode auto change to Black and White.

17
<CAMERA P/N>:
Show the current camera P/N (PAL/ NTSC), The PTZ can automatically
detected some of the camera Signal mode. If not, please set manually.
4.5 CAMERA:
Important Note:Camera setting will vary between Z-22IR and Z-27IR.
For the Simple camera menu access <Main Menu><CAMERA>.
Simple Camera Menu:
<WHITE BALANCE >
White Balance is normally compensated for by the automatic white balance
gain control. In some lighting conditions, user may want to manually adjust
the red and blue settings for optimal viewing. There are 6 options:
[AUTO]: Auto White Balance (default setting).
[MANUAL]: Manually set the red and blue values, setup from 000 to 255.
[ATW]: Auto track White Balance.
[OPW]: Once touch White Balance
[OUTDOOR]: Suitable for outdoor use.
[INDOOR]: Suitable for indoor use.
<BLC MODE>
If the backlight is bright, the objects in the center of the picture may appear
WHITE BALANCE: AUTO
BLC MODE
BACK
EXIT

18
dark. The dome can auto adjust the brightness of the whole image according
to the brightness of the center point. Thus backlight compensation can
increase the brightness of the objects in the center of the picture.
Select<BLC SET>, and choose the right key to access the sub-menu as below
[BLC QTY]: Adjust the data of the BLC, choose from 000-255
[WDR]: ON and OFF the camera’s WDR function (Not supported)
Advanced Camera Menu:
For advanced Menu, Call preset #69.
PLEASE NOTE: Scrolling and changing values in the advanced menu is done
with different controls:
1) The controller joystick has effect.
2) Scrolling up and down is done by pressing IRIS+/IRIS-
3) Changing Values of the selected feature is done by pressing
ZOOM+/ZOOM-
IMPORTANT!!! Changing any values except of in the <DSP SETTINGS> menu
will result in the camera malfunctioning
BLC QTY: 000
WDR: OFF
BACK
EXIT

19
DSP Settings:
FOCUS AUTO
ID DISPLAY OFF
CAM ID 1
PROTOCOL VISCA
BAUD RATE 9600
485 CONTROL NORMAL
LED 1 8
LED 2 15
<DSP SETTINGS>
LANGUAGE ##
RESET
EXIT
SHUTTER AUTO
WB MODE AUTO
AGC 88
DNR ON
BACKLIGHT OFF
HLC LEVEL 48
MIRROR OFF
BRIGHTNESS 8
SHARPNESS 8
<MASK SETTING>
COLOR 8
EXIT