Provision ISR I5PT-390AHDX4 User manual

WARRANTY CARD
[Document subtitle]
[DATE]
LENOVO
[Company address]

Page 2of 9
I5PT-390AHDX4/X10
1080P BULLET MINI PTZ CAMERA
QUICK INSTALLATION GUIDE
Table of Contents:
1. Summary:..........................................................................................................................................................3
1.1 Important Safety Notes:..................................................................................................................................3
2. Box Contents: ...................................................................................................................................................3
3. Structure............................................................................................................................................................3
3.1 Camera Cable..................................................................................................................................................3
4. Device Installation:...........................................................................................................................................4
6. Camera Settings & Preset Commands:.........................................................................................................5
7. Camera Specs:..............................................................................................................................................7

Page 3of 9
1. Summary:
This document describes the correct installation and operation methods of I5PT-390AHDX4/10 Models.
1.1 Important Safety Notes:
Please read this manual carefully before installing and operating the camera.
Please refer to the technical specs to confirm you are using a suitable power supply. Do not use power
supply with higher/lower rating than specified.
Do not attempt to disassemble the camera; in order to prevent electric shock, do not remove any screws or
covers.
There are no user-serviceable parts inside. Please contact the nearest service center if there is any
technical failure.
Avoid incorrect operation, shock vibration or heavy weight pressing which can damage the camera.
Do not use corrosive detergent to clean the camera. If necessary, please use a soft dry cloth to wipe dirt.
For tough contamination, use neutral detergent. Any cleanser for high grade furniture is applicable.
Avoid aiming the camera directly towards extremely bright objects such as the sun, as it may permanently
damage the image sensor.
Please follow the installation instructions.
Do not operate the camera in environments that exceeds the specified temperature, humidity or power.
Keep away from any heat sources such as radiators, heat registers, stoves, etc.
Do not expose the product to the direct airflow of an air conditioner.
2. Box Contents:
ITEM
QUANTITY
IP5-390AHDX4/10 Camera
1
Camera Bracket
1
User Manual
1
Installation Screws
4
3. Structure
3.1 Camera Cable
Please find cable description below. You can also refer to Figure 2-1. There might be some differences among
different serial products.
S/N
ITEM
QUANTITY
1.
Video Connector
AHD 1080P Video Output
2.
Power Connector
12V DC Power Input (2A Recommended)
3
RS-485 Connector
Orange: RS-485A, Yellow: R -485B

Page 4of 9
Picture 2-1: Cable Reference
4. Device Installation:
The camera is designed for a wall installation only! Please refer to the installation instructions below.
Important: The installation surface should be able to hold at least triple the weight of the assembled camera.
Step 1: Install the camera’s bracket to the wall:
For cement wall:
1. Mark the holes locations on the wall.
2. Drill into the marked holes
3. Use the supplied screw anchors
4. Fix the bracket to the wall using the supplied screws.
For wood wall:
1) No need to drill the wall or use screw anchors.
2) Fix the bracket to the wall using the supplied screws.

Page 5of 9
Step 2: Install the camera:
1) Pass the camera’s cable through the installed bracket.
2) Secure the camera to the bracket using the supplied screws.
3) Make all connections (Connect Power source last)
Step 3: Connect the camera to a controller:
1) Connect the camera to a controlling device such as RS-485 keyboard or DVR (By CoC/RS-485).
2) If required, adjust corresponding address and baud rate. Make sure you can control the device.
Warnings:
1) Do not adjust the camera’s orientation manually. This might damage the device.
2) Do not hang anything form the camera’s bracket as it is not designed to hold overloads.
6. Camera Settings & Preset Commands:
Shortcut Key
Function (Set Preset)
Set #84preset
Proportional P/T OFF
Set #85preset
Set Output: AHD PAL
Set #86preset
Set Output: AHD NTSC
Set #87preset,Call N
N is address (N=1,2,3… 255)
Set #88preset,Call N
N is baud rate(1. 2400; 2.4800; 3.9600 )
Set # 89preset
Delete all presets
Set #90 preset
Set left limit Position
Set #91preset
Set right limit Position
Set #92 preset
Delete left/right limit
Set #93preset
Dome restart
Set #94 preset
Restore Factory Setting
Set #95preset
Open main menu
Set #96 preset
0S Park time ON
Set #97 preset
60S Park time ON
Set #98preset
120S Park time ON
Set #99 preset
scan and tour scan speed is automatic
Set #100 preset
scan and tour scan speed is high, 15°/sec
Set #101preset
scan and tour scan speed is middle, 10°/sec
Set #102preset
scan and tour scan speed is low, 5°/sec

Page 6of 9
Note: Sequence default includes preset 1-preset 10 with parking time of 10sec.
Set #103 preset
Record Pattern scan 1
Set #104 preset
Record Pattern scan 2
Set #105 preset
Record Pattern scan 3
Set #106 preset
Record Pattern scan 4
Set #111 preset
Set color-to-black function
Set #112 preset
Set 360°scan, the preset-dwell: 0S
Set #113preset
Set 360°scan, the preset-dwell: 5S
Set #114preset
Set 360°scan, the preset-dwell: 10S
Shortcut key
Function (Call preset)
Call #69 preset
Open Advanced Settings menu
Call #70 preset
Preset Error Correction
Call #71 preset
Proportional P/T ON
Call #72 preset
Start Cruise scan and switch the cruise scan direction
Call #73 preset
Start Pattern 1
Call #74 preset
Start Pattern 2
Call #75 preset
Start Pattern 3
Call #76 preset
Start Pattern 4
Call #77 preset
Call cruise 1 (number 1~16 preset)
Call #78 preset
Call cruise 2 (number 17~32 preset)
Call #79 preset
Call cruise 3 (number 33~48 preset)
Call #80preset
Call cruise 4 (number 49~64 preset)
Call #81 preset
Camera IR-CUT switch
Call #82 preset
Call all valid presets cruise
Call #83 preset
Call 250°scan
Call #95preset
Open main menu (Same response as “Set”)

Page 7of 9
7. Camera Specs:

Page 8of 9

Page 9of 9