Pulsar V33J User manual

ENGLISH
Hour hand
Day hand
Minute hand
Date hand
CROWN
a b c
Second hand
24-hour hand
a: Normal position
b: First click
c: Second click
CAL. V33J
ANALOGUE QUARTZ

English
2
SCREW DOWN CROWN
[for models with screw down crown]
Locking the crown
1Turn Crown counterclockwise until you no
longer feel the threads turning.
2Crown can be pulled out.
1Push Crown back in to normal position.
2TurnCrownclockwisewhilepressingitlightly
until tight.
Unlocking the crown

English
3
TIME/CALENDAR SETTING
DAY AND TIME SETTING
➠
➠
12
3
4
1Pull out to second click when
Secondhand isatthe 12o’clock
position.
2Turnclockwise toadvanceHour
andMinutehandsuntilDayhand
is set to the desired day of the
week.
3Turn to set the time.
4Push back completely in
accordance with a time signal.
CROWN
Second hand
Day hand

English
4
DATE SETTING
1Pull out to first click.
2Turn clockwise to set Date hand
to the desired date.
3Push in.
CROWN
➠
➠
12
3
Date hand

English
5
DAY AND TIME SETTING
●To advance the day hand quickly, turn back the hour and minute hands 4 to 5 hours
beyond the point the day normally changes, and then advance them again until the day
hand is set to the next.
NOTES ON OPERATING THE WATCH
DATE SETTING
●Do not set the date between 9:00 p.m. and 1:00 a.m. Otherwise, it may not turn
properly.
●While setting the date hand, check that it moves properly in one-day increments.
●It is necessary to adjust the date at the end of February and 30-day months.
●When adjusting the day hand, turn the crown slowly.
●When setting the hour hand, check that the 24-hour hand is correctly set.
●When setting the minute hand, advance it 4 to 5 minute ahead of the desired time and
then turn it back to the exact minute.
* The day hand will not move back by turning the crown counterclockwise.

English
6
BATTERY CHANGE
Battery life : Approx. 3 years
Battery : SEIKO SR916SW
3
Years
● As the battery is inserted at the factory to check the function and performance of
the watch, its actual life once in your possession may be less than the specified
period.
● When the battery expires, be sure to replace it as soon as possible to prevent any
malfunction.
● We recommend that you contact an AUTHORIZED PULSAR DEALER for battery
replacement.
WARNING
●Do not remove the battery from the watch.
●If it is necessary to take out the battery, keep it out of the reach of
children. If a child swallows it, consult a doctor immediately.
●Never short-circuit, tamper with or heat the battery, and never expose
it to fire. The battery may burst, become very hot or catch fire.

English
7
CAUTION
●The battery is not rechargeable. Never attempt to recharge it, as this
may cause battery leakage or damage to the battery.

English
8
TO PRESERVE THE QUALITY OF YOUR WATCH
●Non-water resistant
• If the watch becomes wet, have it checked by an AUTHORIZED
PULSAR DEALER or SERVICE CENTER.
●Water resistant 5/10/15/20 bar
• Before using in water, be sure the crown is pushed in completely.
• Do not operate the crown when the watch is wet or in water. If used
in sea water, rinse the watch in fresh water and dry it completely.
• When taking a shower with the water resistant 5 bar watch, or
taking a bath with the water resistant 10, 15 or 20 bar watch, be
sure to observe the following:
* Do not operate the crown when the watch is wet with soapy water
or shampoo.
* If the watch is left in warm water, a slight time loss or gain may
be caused. This condition, however, will be corrected when the
watch returns to normal temperature.
5 bar WR
10/15/20
bar WR
WATER RESISTANCE

English
9
* Pressure in bar is a test pressure and should not be considered as corresponding
to actual diving depth since swimming movement tends to increase the pressure
at a given depth. Care should also be taken on diving into water.
** We recommend that you wear a PULSAR Diver’s Watch for scuba diving.
Your watch will be
adversely affected by
strong magnetism. Keep
it away from close contact
with magnetic objects.
Temperatures over 50°C (122°F)
may cause battery leakage or shorten
the battery life. Do not leave your
watch in very low temperatures below
–5°C (+23°F) for a long time since
the cold may cause a slight time loss
or gain.
However, the above conditions will
be corrected when the watch returns
to normal temperature.
Your watch works with
stable accuracy within a
temperature range of 5°
C and 35°C (41°F and
95°F).
NS
To prevent possible
rusting of the case and
bracelet caused by dust,
moisture and perspiration,
wipe them periodically
with a soft dry cloth.
TEMPERATURES MAGNETISM
CARE OF CASE AND BRACELET
+50°C
-5°C

English
10
Light activities will not
affect your watch, but be
careful not to drop your
watch or hit it against hard
surfaces, as this may
cause damage.
It is recommended that the
watch be checked once
every 2 to 3 years. Have
your watch checked by an
AUTHORIZED PULSAR
Be careful not to expose
the watch to solvents,
mercury, cosmetic spray,
detergents, adhesives or
paints. Otherwise, the
case, bracelet, etc. may become
discolored, deteriorated or damaged.
DEALER or SERVICE CENTER to
ensure that the case, crown, gasket
and crystal seal remain intact.
If your watch has a
protective film and/or a
sticker on the case back,
be sure to peel them off
before using your watch.
2 - 3
Years
SHOCKS & VIBRATION
CHEMICALS
PERIODIC CHECK
PRECAUTION REGARDING
CASE BACK PROTECTIVE FILM