Qlight QMPS-N User manual
1
Panel Mount Audible Alarm
QMPS-N
QMPS-N - 12/24
[Model number] [Voltage]
| |
• QMPS-N
• 12/24-DC12V-24V
• 110/220-AC110V-220V
54
5025
98d
B
ON
RUN
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o-• the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s speci¿cation.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, ¿re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, and or malfunction of the
product that would void the warranty.
1. During wiring or maintenance, please completely turn o-• the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a ¿re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to ¿re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to ¿re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, ¿re, electric shock and loss of life.)
Ordering Specications
Product Specications
Model
number Voltage Current Sound Volume
(dB) Input Method/
No.of ch
Certi¿cate
Weight
QMPS-N
Built-in
standard
sound
DC12V-24V Max.
0.365A Built-in sound :
Max.98dB (Based
on WO-¿re alarm)
Bit input : 5ch
Binary input : 30ch
0.35kg
AC110V-220V Max.
0.110A
0.53kg
※DC type model has a free-voltage range of DC10V-30V.
※AC type model has a free-voltage range of AC100V-240V.
※CE Compliant, UL Listed : DC12V/24V
• Protection rating : IP54
• Ambient operating temperature : -25°C to +50°C
Please scan the QR code for
more detailed product information.
www.qlight.com
2
2 - Mounting Bracket
ON
RUN
5018
68
120
126
4
120
60
111
111
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
QMPS-N-DC QMPS-N-AC
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
ࣧ
ࣩ
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
ࣧ
ࣩ
SOUND
DW
STOP
POWER
BUSY
COM
Ch1
Ch2
Ch3
Ch4
Ch5
EXTERNAL CONTACTEXTERNAL CONTACT
Fuse
Power
Power
Power
Power
EXTERNAL TRASISTOR-NPN EXTERNAL TRASISTOR-NPN
EXTERNAL TRASISTOR-PNPEXTERNAL TRASISTOR-PNP
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Fuse
Fuse Fuse
Fuse
Fuse
Power Power
Common
Common
Common
QMPS-N
Dimensions
(Units : mm)
• When wiring the product with an external transistor, both NPN and PNP type transistors can be used.
Wiring Instructions
3
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
Mounting Bracket Operation
Indicator
Body (ABS)
Front Cover (ABS) Volume Switch
Sound Selection Switch
Fixing Bolt
Parts Denition
Rubber Packing Terminal Block Cover
(PC)
Back Cover (ABS) Terminal Block
Installation
ㆍㆍFirst, cut a square hole (see the above dimensions) on the panel
①to mount the product.
ㆍㆍInsert the rubber packing ②and the product into the square hole of the panel.
ㆍㆍPlace the mounting bracket (2EA)
③and ④ (provided with the product) on the sides of the body and tighten it with a screwdriver
⑤
please ensure the screws are securely tightened.
ㆍㆍMax. thickness allowed for mounting panel is 10mm.
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP54.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating indica-
ted(IP54), it may cause malfunction or damage to the product.
• For further information, please visit our website(www.qlight.com).
4
SOUND SET
VOL.
MIN.MAX.
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
①The red indicator light is on when voltage is supplied to the power
terminal.
②
The green indicator light is on when the product is operating normally.
Operation Indicator
①Loosen the cover ¿xing bolt (M3) fastened at the bottom of the
product.
②Gently press down the front cover and pull it down. (be careful that
the cover may fall o-• if you apply excessive force.)
Removing the Front Cover
RUN
ON
SOUND SET
SD CARD
PLAY MODE
VOL.
MIN.MAX.
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
SOUND SET
ON
1 2 3 4
0
1
2
3
4
5
6
7
8
9
112
+1.0
0.0
112
+1.0
0.0
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
SOUND
DW STOP CH1 CH2 CH3 CH4 CH5
ON
RUN
SOUND
DW
POWER
BUSY
COM
STOP
CH1
CH2
CH3
CH4
CH5
VOL
PLAY MODE
1 2 3 4
ON
SD CARD
ON
RUN
RUN
ON
SOUND
DW
COM
STOP
CH1
CH2
CH3
CH4
CH5
BUSY
POWER
ON
RUN
PLAY MODE
SD CARD
VOL
ON
1 2 3 4
Removing the front cover
Red steady light
Green ashing light
Front Control Conguration
• Built-in sounds can be selected by using
a switch either bit or binary sounds.
• Please be conscious of the number selected
for your desired sound option.
- Switch No. 1 : Select Bit or Binary
- Switch No. 2,3,4 : Select Built-in sound group
■ Select built-in Bit sound group
■
Select built-in Bit sound group or Binary sound group
• It is being used when built-in sound is selected.
• Select between the six sound groups.
• Every group has 5 type of sounds.
• In bit input mode, Please set switch no.1 to
o-•(0).
• In binary input mode, Please set switch no.1
to ON(1).
How to select bit type sound group
Sounds
No. 2 3 4
1 0 0 1
5 Warning Sounds
2 0 1 0
5 Special Warning Sounds (1st Group)
3 0 1 1
5 Melodies
4 1 0 0
5Alarms
5 1 0 1
5 Special Warning Sounds (2nd Group)
6 1 1 0
5 Special Warning Sounds (3rd Group)
ON(1)
OFF(0)
Sound Setting
Sound
Selection
Switch
Volume Switch
Front Control Panel
• The volume output of this product is adjustable.
• Turn the volume dial clockwise to increase the volume, and
turn counter clockwise to decrease the volume.
• There will be no sound when the dial is put at MIN.
Volume Dial
Volume Adjustment
VOL.
MIN.
MAX.
5
①
Terminal for power input.
②
COM terminal for channel selection. Refer to Page2 for connection
method information.
③
Sound channel selection terminal. You can select the sound by using
external contact or transistor.
No. ④, ⑤, and ⑥options are not be used.
Rear Terminal Block Conguration
Connects power
Bit/ Binary input method using rear
terminal block
•
Bit input mode(using external line) allows you to select one of ¿v
e
sound options by switching on one of the 5 channels(Ch1 - Ch5).
• Total of 5 sound options are con¿gurable.
■
Wiring through terminal block with either external contact
or NPN transistor allows either bit or binary input method for
sound channel selection.
•
Binary input mode(using external line) allows you to receive multiple inputs
by using the 5 channels(Ch1 - Ch5) to con¿gure one of 30 sound options.
• Total of 30 sound options are con¿gurable.
■ Bit Input Mode
■ Binary Input Mode
No. 1 2 3 4 5
0 0 0 0 0 0
1 1 0 0 0 0
2 0 1 0 0 0
3 0 0 1 0 0
4 0 0 0 1 0
5 0 0 0 0 1
※
Please note that the
switches shown on the
table is to explain how
to wire the terminal block.
Actual products do not
have switches attached.
Terminal box
0 0 0 0 0 0
1 0 0 0 0 1
2 0 0 0 1 0
29 1 1 1 0 1
30 1 1 1 1 0
ON(1)
OFF(0)
CH1 CH3CH2 CH4 CH5
COM
EXTERNALCONTACT
Binary input mode
Can select up to
30 sound options
Bit input mode
Can select up to
5 sound options
%* %*%* %*%*5612
5170&
&9
6
• In bit input mode, you can chooses one sound from 5 sounds
by con¿guring the 1 channels.
•
This product has a terminal block to select a sound source. For further
details, refer to page 5 ‘Bit/ Binary Input Method using Rear Terminal
Block’ section of this manual.
• For sound con¿gurations, refer to the table below.
■ Bit Input - Playing Built-in Sound
Bit input method sound con¿guration
Type of sound
(WS group as an example)
No. 1 2 3 4 5
0 0 0 0 0 0 No sound
1 1 0 0 0 0 Fire.A-ANG(560Hz-1.5kHz)
2 0 1 0 0 0 Emergency WA-U (600Hz-1.5kHz)
3 0 0 1 0 0 Ambulance PI-PO (450Hz-900Hz)
4 0 0 0 1 0 Machinery Fault(820Hz)
5 0 0 0 0 1 High Expansion(1kHz)
ON(1)
OFF(0)
Sound Type and Combination Manual
■ Sound Type by Group
Bit input method sound con¿guration
Group
Channel
Type of sound
WS
5 Warning
Sounds
Ch1
Fire.A-ANG (560Hz-1.5kHz)
Ch2
Emergency WA-U (600Hz-1.5kHz)
Ch3
Ambulance PI-PO (450Hz-900Hz)
Ch4
Machinery Fault (820Hz)
Ch5
High Expansion (1kHz)
WP
5 Special
Warning
Sounds
(1 st Group)
Ch1
Fire.A-ANG (560Hz-1.5kHz)
Ch2
Abandon Alarm (820Hz)
Ch3
Machinery Fault (820Hz)
Ch4
High Expansion (1kHz)
Ch5
7 Short PI. / 1 Long (1kHz)
WM 5 Melodies
Ch1
Sweet Home
Ch2
For Elise
Ch3
Cuckoo's Waltz
Ch4
Piano Sonata
Ch5
Turkish March
WA 5 Alarms
Ch1
Beep Intermittent
Ch2
Door Chime
Ch3
Phone Ring
Ch4
PI.PI.PI Short
Ch5
Tripping Beat
WO
5 Special
Warning
Sounds
(2 nd Group)
Ch1
Rel rel rel (730Hz-920Hz)
Ch2
Slow Ambulance PI-PO (820Hz-1.05kHz)
Ch3
Wye yong Wye yong (770Hz-1.2kHz)
Ch4
Phone ring 2 (740Hz-910Hz)
Ch5
Fire.A-ANG (770Hz-1.11kHz)
WN
5 Special
Warning
Sounds
(3 rd Group)
Ch1
Oit Oit (500Hz-1.11kHz)
Ch2
Pi o Pi o (940Hz-2.19kHz)
Ch3
Slow Di o Di o (680Hz-840Hz)
Ch4
Li long Li ling (420Hz-470Hz)
Ch5
911 Siren (150Hz-1kHz)
※ Please be noted that the con¿guration chart above is explaining
how to wire terminal blocks. The actual product does not have a
switch.
※ Please be noted that the con¿guration chart above is explaining
how to wire terminal blocks. The actual product does not have a
switch.
•
In binary input mode, you can chooses one sound from
30
sounds by con¿guring the 1 channels.
•
This product has a terminal block to select a sound source. For further
details, refer to page 5 ‘Bit/ Binary Input Method using Rear Terminal
Block’ section of this manual.
• For sound con¿gurations, refer to the table below.
• Please be aware that the con¿guration for sound using the
binary input method is di-•erent from the bit input method.
■ Binary Input - Playing Built-in Sound
Binary input method sound con¿guration
Type of sound
No. 1 2 3 4 5
0 0 0 0 0 0 No sound
1 0 0 0 0 1 Fire.A-ANG (560Hz-1.5kHz)
2 0 0 0 1 0 Emergency WA-U (600Hz-1.5kHz)
3 0 0 0 1 1 Ambulance PI-PO (450Hz-900Hz)
4 0 0 1 0 0 Pi-ik Pi-ik (800Hz)
5 0 0 1 0 1 Machinery Fault (820Hz)
6 0 0 1 1 0 High Expansion (1kHz)
7 0 0 1 1 1 Alarm (1kHz)
8 0 1 0 0 0 Sweet Home
9 0 1 0 0 1 For Elise
10 0 1 0 1 0 Cuckoo's Waltz
11 01011Piano Sonata
12 0 1 1 0 0 Turkish March
13 0 1 1 0 1 Magic Flute
14 0 1 1 1 0 Badinerie
15 0 1 1 1 1 Pineapple Rag
16 1 0 0 0 0 Beep Intermittent
17 1 0 0 0 1 Door Chime
18 1 0 0 1 0 Phone Ring
19 1 0 0 1 1 PI.PI.PI Short
20 1 0 1 0 0 Tripping Beat
21 1 0 1 0 1 Rel rel rel (730Hz-920Hz)
22 1 0 1 1 0 Slow Ambulance PI-PO
(820Hz-1.05kHz)
23 1 0 1 1 1 Wye yong Wye yong
(770Hz-1.2kHz)
24 1 1 0 0 0 Phone ring 2 (740Hz-910Hz)
25 1 1 0 0 1 Fire.A-ANG (770Hz-1.11kHz)
26 1 1 0 1 0 Oit Oit (500Hz-1.11kHz)
27 1 1 0 1 1 Pi o Pi o (940Hz-2.19kHz)
28 1 1 1 0 0 Slow Di o Di o (680Hz-840Hz)
29 1 1 1 0 1 Li long Li ling (420Hz-470Hz)
30 1 1 1 1 0 911 Siren (150Hz-1kHz)
ON(1)
OFF(0)
7
Operation Method and Setting
When Using a Built-in Sound Source
Bit input Binary input
Play one of ¿ve sounds from
6 groups Play one of 30 sounds
■ When using a built-in sound source in bit input mode
1. Please set switch no. 1 to o-•.
- For more information, see page 4
‘Sound Selection’
section.
2. Use one of the SOUND setting switches 2, 3and 4 to select one of the
6 groups.
- For more information, see page 4
‘Sound Selection’
section.
3. Use the terminal block on the back to select one of the ¿ve built-in
sounds.
- For more information, please refer to page 6
‘Sound Type and Combi-
nation for Built-in Sound’ - ‘Bit Input’
section.
※Sound switch setting → Channel selection
■ When using a built-in sound source in binary input
mode
1. Please set switch no. 1 to ON.
- For more information, see page 4
‘Sound’
section.
2. Use the terminal block on the back to select one of the 30 built-in
sounds.
- For details, please refer to page 6
‘Sound Type and Combination for
Built-in Sound’ - ‘Binary input’
section.
※Sound switch setting → Channel selection
Head O-ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. +82-2-2679-6152(Toll free. +82-80-328-2222) Fax. +82-2-2679-6154
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. +82-55-328-1111(Toll free. +82-80-328-1111)
Qlight OverSEAs Sales Dept |
704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : +82-51-620-4100
Qlight Public Relations & Marketing Team O-ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. +82-51-245-0017
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. +1 - 408 - 519 - 5740 Fax. +1 - 408 - 519 - 5739
China Factory/ Shanghai Sales O-ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86
-
21
-
6651
-
7100 Fax. +86
-
21
-
6315
-
3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86
-
513
-
8384
-
9999 Fax +86
-
513
-
8384
-
9910
Product Operation Inquiry / Customer Support +82-51-620-4100
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea ( Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea ( Postal Code : 50805)
For your safety
Speci¿cation and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - QMPS-N - 2209A
Table of contents
Other Qlight Security System manuals
Qlight
Qlight QWT Series User manual
Qlight
Qlight QWT User manual
Qlight
Qlight EMCL70 User manual
Qlight
Qlight STDL User manual
Qlight
Qlight QWCD35 User manual
Qlight
Qlight SEDLR User manual
Qlight
Qlight QWCD50 User manual
Qlight
Qlight ETAR50MCL Series User manual
Qlight
Qlight Q100L User manual
Qlight
Qlight ETA50MCL Series User manual
Qlight
Qlight S125D Series User manual
Qlight
Qlight SAB130 User manual
Qlight
Qlight QMPS User manual
Qlight
Qlight ET50MCL Series User manual
Qlight
Qlight S150RS User manual
Qlight
Qlight SBE130 User manual
Qlight
Qlight S100D Series User manual
Qlight
Qlight S100D User manual
Qlight
Qlight QMPS User manual
Qlight
Qlight SM30 User manual
Popular Security System manuals by other brands
ADEMCO
ADEMCO Vista-10P Installation and setup guide
DELTA DORE
DELTA DORE Pack TYXAL+ Access Quick installation guide
Pima
Pima SRO743 Installation and programming instructions
Whelen Engineering Company
Whelen Engineering Company 1502M INSTALLATION WIRING GUIDE
American Dynamics
American Dynamics RABW4QUAD Installation and setup guide
NAPCO
NAPCO MAGNUM ALERT 854 SYSTEM manual
