Qlight ETAR50MCL Series User manual

Product Specications
ETAR50MCL Series
Model number Layers Voltage Current Certicate Weight Color
ETAR50MCL
Steady
ETAR50MCL-BZ
Steady w/built-
in buzzer
ETAR50MCLF
Flashing
ETAR50MCLF-BZ
Flashing w/
built-in buzzer
3DC24V 0.085A 0.55Kg
R-Red
A-Amber
G-Green
ETAR50MCL - 24 - R
[Model number] [Voltage] [Color]
| | |
• ETAR50MCL
• ETAR50MCL-BZ
• ETAR50MCLF
• ETAR50MCLF-BZ
• 24 - DC24V R-Red
A-Amber
G-Green
20
85dB
5525
Ø50
Ø77
360°/3-Ø4
Ø17 CABLE ENTRY
350±3
PCD65
ETAR50MCL, ETAR50MCL-BZ, ETAR50MCLF, ETAR50MCLF-BZ
Industrial LED beacon
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
1. During wiring or maintenance, please completely turn o󰀨 the
power of the product. (Failure to follow this may lead to an electric
shock.)
2. Do not install the product in locations that subjects it to excessive
dust or water other than the conditions designated by the IP
protection ratings indicated for each product. (Failure to follow
these instructions may cause a re to the product, electric shock,
physical injury, malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service
is required, please contact your local Qlight contact point.
(Failure to follow these instructions may lead to re, electric shock,
or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow
these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives
or property, please make sure to have a double safety device.
(Failure to follow this may cause damage to property, re, electric
shock and loss of life.)
Precautions for Safety
Failure to follow the instructions below may cause a
loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation
around the product.
2. Please turn o󰀨 the power of the product immediately if it fails
to operate properly.
3. Carefully wire the product according to each product’s
specication.
4. Please be careful in preventing chemicals such as thinner,
benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause
malfunction or damage to the product, re, and electric
shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause
damage to property, the product, or malfunction of the
product that would void the warranty.
Dimensions
(Units : mm)
Ordering Specications
Please scan the QR code for more
detailed product information.
www.qlight.com

ETAR50MCL, ETAR50MCL-BZ, ETAR50MCLF, ETAR50MCLF-BZ
※ ETAR50MCL, ETAR50MCL-BZ: Steady
ETAR50MCLF, ETAR50MCLF-BZ : Flashing
ETAR50MCL, ETAR50MCL-BZ, ETAR50MCLF, ETAR50MCLF-BZ
PCD 65
3-Φ6 HOLES
Min.Ø5 CABLE ENTRY
EN - ETAR50MCL - 2305A
Lens(PC)
Bolt
Flange nut
Bracket(Al)
Housing(Al)
Red
Amber
Green
Brown
Black
Red
Amber
Green
Brown
Black
Power
Power
Fuse
Fuse
Red
Amber
Green
Buzzer
Red
Amber
Green
Buzzer
Product Operation Inquiry / Customer Support [phone]
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
www.qlight.com
Mounting Hole Specications Installation Environment and Protection Rating
• This product is designed for indoor use with protection rating of IP20.
• If the product is installed in locations that subject it to excessive dust
or water other than the designated IP protection rating
indicated, it may cause malfunction or damage to the product.
• For further information, please visit our website (www.qlight.com).
• Machine holes on the mounting surface referring to the
diagram below.
• ETAR50MCL series can be wired by using both external contact
and transistor.
• Wiring to transistor, use the PNP transis- tor. Please wire properly
based on wiring instructions.
• External power/ signal line - UL1007 AWG22(0.3sq) 400mm
• Please disassemble the M4 bolts placed in mounting bolts and
place the bracket on to desired mounting surface.
• Tighten the ange nuts from the opposite side of the mounting
surface.
Wiring Instructions Parts Denition/ Installation
External transistor-PNP
External contact