Qlight S100D User manual

S100D / S125D
Thank you for purchasing Q.Light product.
Please read this manual carefully before installing this system
for safe and long use of the product.
▪ Ensuring high revolving durability by applying a small bearing to
the revolving axis.
▪ Max. 105dB output in spite of small size of the product.
▪ RPM : 120-140/Min.
▪ Material : Lens-AS. Body-ABS, Reflector-Heat Resisting ABS
▪ Protection Class : IP54
▪ Each model has 5 sound tones built-in. Select a suitable sound
tone for the purpose of use
1) S100D
▪ General Specification
Model Rated
Voltage Current Bulb Weight Color
DC12V 0.930A 12V10W T16x3515S 9
DC24V 0.660A 24V10W T16x3515S 10 1.05Kg
AC110V 0.123A 12V10W T16x3515S 9
S100D
AC220V 0.064A 12V10W T16x3515S 91.44Kg
Red-R
Amber-A
Green-G
Blue-B
▪ External View Drawing
2) S125D
▪ General Specification
Model Rated
Voltage Current Bulb Weight Color
DC12V 0.930A 12V10W T16x3515S 9
DC24V 0.660A 24V10W T16x3515S 10
1.07Kg
AC110V 0.128A 12V10W T16x3515S 9
S125D
AC220V 0.067A 12V10W T16x3515S 91.46Kg
Red-R
Amber-A
Green-G
Blue-B
▪ External View Drawing
Type Main Built-in
Sound CH Sound Tone Volume
WS 5 Warning
Sounds
ch1
ch2
ch3
ch4
ch5
Fire A-ANG(Wail)
Emergency WA-U(Yelp)
Ambulance PI-PO(High-Low)
Machinery Fault( PI-PI-PI-)
Foam Release Alarm(PI~ Continuous)
105dB
WM 5 Melodies
ch1
ch2
ch3
ch4
ch5
Sweet Home
For Elise
Cuckoo’s Waltz
Piano Sonata
Turkish March
105dB
WA 5 Alarms
ch1
ch2
ch3
ch4
ch5
Beep(Intermittent)
Door Chime
Phone Ring
Machinery Fault(PI.PI.PI.PI.)
Tripping Bead Sound
103dB
WV 3 Voice
Signals
ch1
ch2
ch3
Reproduction of Voice Recording
3 Channels 95dB
Power line and signal line come out from the product.
Please refer to below wiring diagram for correct connection
of power supply and signal line.
▸ Power Line : UL1015-NO.16(1.25sq) x 2C 400mm
▪ In case of product using AC voltage : Connect the line without
polarity(wire color).
▪ In case of product using DC voltage : Black line is negative(-).
OPERATING MANUAL
Bulb Revolving Warning Light with Phone

▸ Signal Line : UL1007-NO.22(0.3sq) 400mm
▪ This product was manufactured with the structure for indoor use.
Installing in any direction is okay for indoor use.
▪ Outdoor use is limited at a place where no water or very little
water percolates. Mounting also should be done only with
vertical standing shape.
▪ Mount at the place where exists low vibration, low impact, low
moisture and low dust as long as possible.
▪ Refer to below information and drill necessary mounting holes on
profitable part of the product.
(Make sure PCD from external view drawing.)
▪ Fix the product by using nuts(M5-3EA) originally equipped on
mounting bolt on bottom of the product.
Refer to following drawing and explanation for right operating.
S100D S125D
1) Lens Removal
Remove lens① by turning it counterclockwise and make sure
related parts on assembling board②.
2) Bulb Change
※ Warning ! Turn off Power
Must turn off power supply and change the bulb after at least
1 minute.
▪ Make sure the rated voltage and wattage of new bulb. If the
voltage of new bulb is higher than that of original bulb, the
self-life of product can be reduced and can cause damage on
lens and reflector. Therefore, please use same bulb as original
one which has same rated voltage and wattage or lower one.
▪ Bulb Removal : Press slightly the bulb downward and turn it
counterclockwise for removing.
▪ Bulb Fitting : Fit new bulb into the socket by pressing it
clockwise.
Bulb Removing Bulb Fitting
3) Lens Assmebling
Assemble the lens in reverse order of separating.
▪ If using voltage is seriously higher or lower than rated voltage, it
can reduce the self-life of the product or can cause a problem
on product operating. Make sure the using voltage does not
exceed +/- 5% of the rated voltage.
▪ If lens or body of the product is contaminated by chemicals such
as thinner, benzene, the product can be damaged, discolored
or deformed. Please be careful.

▪ Do not give strong impact to the product. It can be a reason of
wire disconnection or short circuit.
▪ Do not strongly pull the wire out from the product. It can cause a
disorder.
▪ In case of product using AC voltage, do not allow power
supply either to common line or to signal line..
Situation Main Cause Solution
Non Lighting Wire Disconnection
with Bulb
Wire Re-connection or
Bulb Change
Supplying Voltage Lower
Than Rated Voltage
Making Sure Using
Voltage
Wrong Selecting Voltage
Selection Switch to 220V
(In Case of AC Type)
Selecting Voltage
Selection Switch to
110V
Feeble Lighting
Low Revolving Speed
Sound Tone Deterioration
Wrong Operating Revolving
Speed Control Volume
Turn the Volume
Clockwise
Short Self-Life of Bulb Supplying Voltage Higher
than Rated Voltage
Making Sure Using
Voltage
Lens Deformation Caused
by Bulb Overheating
Damage on Transformer
(AC Type)
The Voltage of Bulb
is Higher than Rated
Voltage
Changing Bulb with
Rated Voltage
Non Revolving Problem with Motor Contact Q.Light or
Their Agent
Short Circuit of Sound Tone
Signal Line Making Sure Wiring
Double Sound Tone Problem with Sound Tone
Selection Switch
Contact Q.Light or
Their Agent
Wrong Wiring Making Sure Wiring
No Power Supply Making Sure Wiring
No Sound
Problem with Horn Contact Q.Light or
Their Agent
Q-LIGHT CO., LTD.
http://www.qlightkr.com
E-mail : [email protected]
Seoul Office (Domestic Sales & A/S)
Tel) 02-2679-6152
Ansung BD A-312, 410-13 Sindorim-Dong, Guro-Gu, Seoul
Overseas Marketing Team / Plant
Tel) 055-328-4082 Fax) 055-328-4083
Plant #1 : 178-1 Woogye-Ri, Sangdong-Myun, Kimhae-Si,
KyungNam, Korea
Plant #2 : 417-1 Geumsa-Dong, Geumjung-Gu, Busan