Quoizel TF1180TVA User manual

Part Description Quantity
A
Finial
1pc.
1pc.
1pc.
1pc.
1pc.
B
C
D
F
Spacer Tube
Shade
Package Contents
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone [phone]
Fax [phone]
www.quoizel.com
Pleasegoto forproductcleaningtips.Gotothe
selection.
(2)MediumBase75WMaximum,Alternatebulb(1)19WCFL.
15-20minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackage
contentlistanddiagramsbelowtobesureallpartsarepresent.Ifanypartsaremissingor
damaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer
serviceforreplacementparts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:None
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Nipple with Knurled Nuts
Check Ring
Assembly Instruction Sheet #IS-TF1180TVA
For Style TF1180TVA
A
BC
D
F
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
1of3
March2015
REV.A
G
1pc.
G
Base E
1pc.
EFlat Washer

TF1180TVA
FINISH: VILIANT BRONZE
PART NUMBER
11180TVATF
G3260SH
(2)Medium Base
Bulbs
(Not Supplied) NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
BASE VALIANT BRONZE TF1180TVA
SHADE TIFFANY 16"SQ X 7.5"H
REQ.
1
1
NO.
1
2
2of3
16” SQ.
8”
16”
25”
6.5” SQ.
1
2
REV.A

6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
STEP 1 -Attach Spacer Tube, Check Ring and
Nipple with Knurled Nuts to Base
A. Remove Knurled Nuts from the Nipple (G). Screw one
end of the Nipple (G) into the Hex Coupling on the top
center of the Base (F). Hand tighten until snug.
B. Place the Spacer Tube (D) and Check Ring (B) over the
top end of the Nipple (G). Secure by threading the Small
Knurled Nut onto the Nipple (G). Hand tighten until
snug.
C. Thread the Big Knurled Nut onto the top end of the
Nipple (G) and adjust to proper location for the Shade
(A) and Finial (C).
Figure 1
Small Knurled Nut
STEP 2 -Attach Shade and Finial
A. Place the Flat Washer (E) and Shade (A) over the top
end of the Nipple (G). Secure by threading the Finial (C)
onto the Nipple (G). Hand tighten until snug.
Finial
Figure 2
Nipple
Shade
Nipple
STEP 3 Install Bulb-
A. This fixture uses standard bulb with medium base .
Maximum 75 watts.
B. Insert bulb and screw snugly into place.
Your table lamp is now assembled and ready to use.
Enjoy!
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
3of3
Assembly Instruction Sheet #IS-TF1180TVA
For Style TF1180TVA
Base
Big Knurled Nut
Hex Coupling
Spacer Tube
Check Ring
Base
Figure 3
Bulb
Socket
Flat Washer
March2015
REV.A