Quoizel PO9140K Mounting instructions

1of3
Assembly Instruction Sheet #IS-PO9140_R1
For Style PO9140XX
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Pleasegoto forproductcleaningtips.Gotothe selection.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,Shovel,Electricaltape,Wirecutter,Safety glasses, Wire strippers and proper length
wires(notsupplied).
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
2016 QuoizelInc. RevisedDate:2016-10-24
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Package Contents
BSmall Allen Wrench
x1
ABig Allen Wrench
x1
CAnchor Bracket
x1
DAllen Bolt
x3
ELock Ball
x3
FWasher
x3
Lock Washer
x3
G
Hex Nut
x3
H
Anchor Bolt
x3
I
JAllen Set Screw
x4
KPost Fitter
x1
LUpper Post
x1
MMiddle Post
x1
NBottom Post
x1
STEP 1 Assemble Anchor Bolts to the Anchor Bracket-
A. Remove all Lock Washers (G), Hex Nuts (H) and Lock Balls (E) from
the Anchor Bolts (I).
B. Screw the threaded end of each Anchor Bolt (I) in the Mounting
Bracket (C) making sure to that the Anchor Bolt (I) is 1.75” to 2”
extended from the bottom of the Bracket (C).
C. Place a Lock Washer (G) over the Anchor Bolt (I) and then thread the
Hex Nut (H) onto each Anchor bolt (I). Securing the Bracket (C) in
place maintaining the 1.75”-2” length of the Anchor Bolt (I).
1.75” - 2”
H
G
C
I
C
G
H
I
Figure 1
STEP 2 Install Anchor
Bolts in the ground
-
A. Dig a hole in the ground at
the desired location for the
Post Mount.
B. Use cement to secure the
Anchor Bolts (I) into the
ground making sure that
the Bracket (C) is flush on
top of the cement and level
Anchor at the desired
grade with the ground. This
is the base for the Post
Mount.
Tube
Cement
Earth
Earth
Wires
1.75” - 2”
Dia. 9-11/16”
Bolt
Bolt Circle
C
I
Figure 2

2of3
2016 QuoizelInc. RevisedDate:2016-10-24
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 3 Assemble Post Fitter and Posts
together
-
A. Place the Post Fitter (K) on the Upper
Post (L) end without the threads. Secure
the Post Fitter (K) with (2) Allen Set Screw
(J) using the Small Allen Wrench (B)
provided.
B. Thread the Upper Post (L) assembly onto
the Middle Post (M) until secure. Secure
the Upper Post (L) assembly to the Middle
post (M) using (2) Allen Set Screw (J) and
the Small Allen Wrench (B) provided.
C. Place the Middle Post (M) assemble onto
the Bottom post (N) lining up the mounting
holes in the Middle Post (M) assembly
with the Bottom Post (N). Secure the
Middle Post (M) assembly to the Bottom
Post (N) using (2) Allen Bolt (D) and the
provide Big Allen Wrench (A). Tighten until
secure.
Figure 3
N
D
A
M
B
J
L
KSTEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 - Install Post Mount Assembly to Anchor Bolts
A. (I)
(F) (I) (I)
(E)
Place the Post Mount assembly onto the Anchor Bolts . Place a
Washer over each Anchor Bolt and secure each Anchor Bolt
with the Lock Ball and tighten until secure.
Your installation is completed now. Restore electricity. Retain this
sheet for future reference.
Earth Earth
N
E
F
I
C
Figure 5
INSTALL POST LIGHTING TO POST MOUNT
ToolsRequired: marking pen, 5/32” drill bit, center punch, hammer,drill,#10self-tappingscrew,andwrench.
STEP 1 -Mark the Location of the 3 Mounting Holes
A. Place the light fixture onto the post fitter and mark the location of
the 3 mounting holes on the fixture fitter onto the post fitter with the
marking pen.
Figure 1
Post Fitter Post
Fitter
Marking Pen
Mounting
Hole
STEP 2 M C E M H-arking the enter of ach ounting ole
A. Remove the light fixture. Using the center punch and hammer
marking the center of each mounting hole location that is marked
with the marking pen.
Figure 2
Post Fitter
Center Punch
Hammer Marking
Post
Lighting

3of3
2016 QuoizelInc. RevisedDate:2016-10-24
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 3 Drill Holes-
A. Using the 5/32” bit and drill, drill a hole completely through the post
fitter at each (3) locations marked in step 2 above.
Post Fitter
5/32” bit and drill
STEP 4 Attach the fixture to
the Pier Mount
-
A. Wire the fixture according to
the instructions and place the
fixture on the post fitter lining
up the mounting holes on the
fixture fitter with the holes on
the post fitter.
Figure 4
Post Fitter
Hole
Fixture
Fitter
#10 Self-tapping
Screw
Mounting
Hole
Figure 3
B. Use the #10 Self-
tapping Screws (not
provided) to attach
the fixture to the post
fitter.
Post
Lighting