Rad2Go ZZ CRUISER E-023 User manual

ZZ Cruiser
E – 023
USER MANUAL

JET USA
INSTRUCTION
1. To prolong motor life, push start the scooter before applying
power.
2. Power handle returns to ‘off’when released.
3. Release power handle before applying brake. Do not apply
power when brake is on.
4. Charge battery and discharge at lease once every 90 days.
5. Check tire pressure regularly.
6. Do not leave the scooter in direct hot sun for long periods.
7. Operate safely and in good weather only, use safety gear
including helmet.
8. Obey the law in your city and state in all operations.
9. You are responsible for operating safely and seller assumes
no liability for misuse or operator negligence.
Note: Riding up a steady incline for a prolonged periods of time
will cause the controller to automatically cut power to the motor
to avoid burn out. In such a case let the motor cool for about 2-3
minutes before turning back on.
1

JET USA
IMPORTANT CHARGER AND BATTERY SAFETY
INSTRUCTIONS CHARGING INSTRUCTIONS
1. Lay scooter flat with on/off switch in ‘off’position.
2. Plug charger cord into scooter first, then plug into 110V, 120V, 220V,
or 240V outlet.
3. Charge for 6-8 hours. The LED will be red during charging and when
fully charged, the LED will turn green.
4. Do not overcharge, unplug unit after 8 hours to avoid overheating risks.
5. Charge unit after low charge warning and every 90 days.
BATTERY INSTRUCTIONS
1. Change the battery if any leaks, breaks or cracks appear.
2. Do not touch the battery liquid solution, flush with water if contact is
made.
3. Dispose of battery according to state and local laws.
Accelerator
Rear brake
Deck
Batteries
Front Wheel
Power switch & Power indicate light
Kick stand
2

JET USA
Entire scooter
Take out scooter from cartons
3

JET USA
E-023 GENERAL
CONNECTION DIAGRAM
Wiring Diagram
+
-
-
Controller
RED
BATTERY CHARGER
+
+
-
+
-
YELLOW
BLACK
GREEN
RED
BLACK
RED
BROWN
BLACK
RED
GREEN BRAKE
SWITCH
MOTOR POWER
INDICATOR
SPEED
CONTROLLER
POWER
SWITCH BLACK
RED
24V9AH
BATTERY
4

JET USA
Basic functions and specifications
Material: Fiber glass deck and steel body
Dimensions: 33 ×22.86 ×106 cm
Gross weight: 21.09 kgs
Net weight: 18.33 kgs
Maximum speed: 19.31 kmh
Average tralvel distance: 17.7 kms
Power-driven max.load capacity: 90.72 kgs
After every charging: To travel for 1 consecutive hour
Brake: Handle control to rear wheel by drum brake
Tire: Airless tire
CHARGER
Moder No. Input Output Charging time
AC0224A 100V~240V ~1.2A 24.0V ~ 1.0A 6~8 Hours
MOTOR
Moder No. Rated voltage Rated current Output power
RPD-24 DC24V 15.5A 200W
BATTERY
Nominal capacity Voltage Weight Charging time
Lead acid storage battery 9AH 24V 8kg >=250 times
SIMPLE INSTALLATION DRAWING
5

JET USA
Safety Lever
Quick Release
Lever
Unfold the ZZ Cruiser
1. Lift the quick release lever and push down the safety lever.
2. To unfold the handlebar column grasp it in the middle and raise it to an
upright position. (to uplift the safety lever to make sure it’s at the right
position)
3. Push the quick release lever down to lock it into the position.
Folding the ZZ Cruiser
1. Lift the quick release lever
2. Push down the safety lever & lay the handlebar down on top of the
deck.
3. Uplift the safety lever to lock the handlebar at the folding position.
4. Push down the quick release.
6

JET USA
1. set handlebar upright and
secure
2. Press the spring button
and insert handles spring
button holes in the T
shaped handlebar.
3. Ensure speed control on
right, brake on left.
Presstheclip adjustupanddown
7

JET USA
MAINTENANCE
1. Inspect the entire scooter before each use; check the brake,
speed control, belt and wheels, including tire pressure.
2. If you hear any unusual noise, stop and check the motor and
do not operate if improper noises.
3. Clean the scooter regularly and avoid long hot sun exposure.
4. Lubricate the front and rear axle, chain and all turning parts.
[ see charg 1]
chart 1 Termly Inspection and Maintenance Range
300miles 600miles 12miles 1800miles
Brake A I A I
Different control pull lines L I L I
Tire I I I I
All the connect lines I I T I
Front fork and frame I I I I
ATTENTION: I:inspect, clean and adjust T:tighten A:adjust
L:lubricate
8