RadiSys PM6165B ONT User manual

Quick
Installation Guide
PM6165B ONT
Document Revision 0.1 (draft)

© Copyright 2023. Radisys Corporation, All Rights Reserved. 3Radisys 6165B ONT Quick Installation Guide2
Interfaces Specication
VoIP 1 FXS ports (RJ11)
USB USB 2.0 Type A
Power Adaptor Input 90-240VAC, 50/60Hz
Power Adaptor Output +12VDC nominal, 2A
Operating Temperature 0 to 40°C (32 to 104°F)
Operating Humidity 5 to 90% (non-condensing)
Dimensions 220 x 160 x 40 mm (W x D x H)
2.3 Interfaces
Item Description
1 LEDs Status LEDs
2 POWER Power port for external Power Adaptor
3 ON/OFF Button Turn power ON or OFF
4 RESET Reboot ONT (quick push)
1 Introduction
The Radisys PM6165B XGS-PON Home Gateway Unit (HGU) is a Wi-Fi6
dual-band XGS-PON complying with the ITU-T G.9807.1 standard. The
gateway is best suited for FTTH residential and small ofce use.
2.1 Contents
- PM6165B ONT
- Quick Installation Guide
- Power Adaptor
2.2 ProductSpecications
Interfaces Specication
WAN Uplink GPON port (SC/APC)
Ethernet 1 100/1000/10G Base-T port (RJ45)
4 10/100/1000 Base-T ports (RJ45)
Wi-Fi 2x2/2x2 Wi-Fi 6 (internal antennas)
41. 00 mm
61. 00 mm
90. 00 mm
RESETPOWER PHONE
LAN1LAN2
LAN3
LAN4
USBWPS
ON/OFF 10G LAN
46 m m 22 0 mm
16 0 mm
RESETPOWER PHONE
LAN1LAN2
LAN3
LAN 4
USBWPS
ON/OFF 10G LAN
POWER
XGS-PON LOS Internet 10G LAN
LAN4LAN1USB2.4GHzLAN3 LAN25GHz PHONEWPS
1
2 3 5
4 6
7 8 9

© Copyright 2023. Radisys Corporation, All Rights Reserved. 5Radisys 6165B ONT Quick Installation Guide4
Label Color Status Denition
LAN1-4 Green ON Ethernet port interface is linked
Activity (ash) Data transmitting
OFF Ethernet port is disabled or no service
10G LAN Green ON Ethernet port interface is linked
Activity (ash) Data transmitting
OFF Ethernet port is disabled or no service
2.4GHZ Green ON 2.4GHz Wi-Fi radio is enabled
Slow Blink (1/s) 2.4GHz Wi-Fi radio transmitting data
trafc
OFF 2.4GHz Wi-Fi radio is disabled
5GHZ Green ON 5GHz Wi-Fi radio is enabled
Slow Blink (1/s) 5GHz Wi-Fi radio transmitting data
trafc
OFF 5GHz Wi-Fi radio is disabled
WPS Green Slow Blink (1/s) WPS push-button activated
OFF WPS is not active
PHONE Green ON Telephone port registered for service
Slow Blink (1/s) Telephone line is off hook
OFF Telephone port is disabled or un-reg-
istered
USB Green ON Device is connected to USB port
OFF No device connected
Item Description
Reset to factory (press and hold for 10 seconds)
5 WPS Press to initiate WPS connection
6 USB USB port for ancillary equipment
7 10GE 10GE Ethernet ports for PC or LAN (RJ45)
8 GE 1-4 1GE Ethernet ports for PC or LAN (RJ45)
9 TEL 1 Phone port for telephony (RJ11)
2.4 LED Status Indicators
Label Color Status Denition
POWER Green ON Normal operation
Rapid blink Reset to factory defaults, not cong-
ured for service
Slow blink (1/s) Initializing, start of boot process
XGS-PON Green ON WAN interface ranged and linked
Slow Blink (1/s) WAN ranging in process
OFF Not ready for ranging or provisioning
LOS RED OFF No alarm
ON Loss of Signal (LOS) alarm
INTERNET Green ON Internet service available, IP address
OFF Internet service not available, IP or
DNS failure
POWER
XGS-PON LOS Internet 10G LAN
LAN4LAN 1USB2.4GHzLAN3 LAN 25GHz PHONEWPS

© Copyright 2023. Radisys Corporation, All Rights Reserved. 7Radisys 6165B ONT Quick Installation Guide6
3.2 Mounting ONT on a wall
ONT has two mounting holes that can be used for wall mount placement.
Please see diagram for screw separation and location.
ONT should be mounted with LEDs facing up and service interfaces facing
down to avoid dust and contamination.
4 Web Graphical User Interface
You can access the ONT through a web browser using the following steps:
- Connect an Ethernet cable from your computer to any of the 10G
or LAN 1 - 4 ports.
- Launch a web browser or telnet session and connect to a
ddress 192.168.1.1.
- After response, enter the following:
1. Username : user
2. Password: user
After initial login, it is recommended that password be changed.
3.1 Installation
1. Remove ONT from packaging.
2. Lay ONT at on surface or attach ONT to wall.
3. Remove protection plug (black) from WAN port.
4. Connect ber optic cable with SC/APC termination to WAN port.
5. Connect telephone cable (5) with RJ11 termination to PHONE.
6. Connect Ethernet cable (6) with RJ45 termination to 10G LAN
and LAN 1-4. Recommend CAT6 or better Ethernet cable for
10GE port.
7. Connect Power Adaptor cable (7) with 2-pin barrel to POWER port.
8. Plug in Power Adaptor into electrical outlet.
9. Push ON/OFF button. Check LED power up sequence.
User note: ONT may be upgraded to newer software image prior to
provisioning of services. ONT may reset after initial boot up sequence is
complete or software image is upgraded.
5
6
RESET
POWER
PHONELAN1LAN2LAN3LAN 4
USB
WPS
ON/OFF 10G LAN
7
POWER
XGS-PON
LOS Internet 10G LAN
LAN4LAN1 USB2.4GHzLAN3
LAN2 5GHz PHONEWPS

© Copyright 2023. Radisys Corporation, All Rights Reserved. 9Radisys 6165B ONT Quick Installation Guide8
6 Limited Warranty
The product warranty does not cover damage resulting from hardware
being installed in areas subject to rain, high humidity, water ingress and
dust or debris. Disassembling product or removing enclosure cover from
the assembly is a safety hazard and will void warranty. PM6165B may only
be repaired by authorized service personnel.
5 Caution
Please follow the instructions below to avoid physical injury:
- This unit is for indoor use only.
- All Ethernet, telephone and power wiring are limited to inside
of the building.
- You should not install ONT during lighting storms to avoid
electrical shock.
- Never look directly at the ber port and ber cable ends when
they are powered on.
- DO NOT plug in, turn on or attempt to operate an obviously
damaged unit.
- DO NOT use near water.
- DO NOT operate ONT in a location where maximum ambient
temp. exceeds 40°C.
- DO NOT place near high temperature source.
- Set up the unit away from direct sunlight or other electrical
equipment.
- Open optical connections must use a protective cap under all
circumstances to protect against physical damage and dirt.
- Avoid impact stresses when handling connectors.
- Physical damage to optical connections impairs transmission quality.
- Avoid a bend radius in excess of 30 mm for ber optic links.
- Check the available voltage supply.
- Only connect approved accessories.
- This equipment is not suitable for use in locations where children
are to be present.
- DO NOT disassemble the unit.

© Copyright 2023. Radisys Corporation, All Rights Reserved. 11Radisys 6165B ONT Quick Installation Guide10
This page is intentionally left blank This page is intentionally left blank

Radisys 6165B ONT Quick Installation Guide12
RSYSQG6165BONT12062023A