Rae DoseRAE 2 User manual

DoseRAE 2
Electronic Personal Dosimeter
For X-Ray & Gamma Radiation
User’s Guide
P/N 035-4025-000 Rev. A
March 2011

© 2011 RAE Systems, Inc.

DoseRAE 2 User’s Guide
1
1 Read Before Operating
This manual must be carefully read by all
individuals who have or will have the responsibility
of using, maintaining, or servicing this product. The
product will perform as designed only if it is used,
maintained, and serviced in accordance with the
manufacturer’s instructions.
2 Warnings
For safety reasons, this equipment must be operated
and serviced by qualified personnel only. Read and
understand the user manual completely before
operating or servicing.
WARNING
Substitution of components may impair safety.
This product complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.

DoseRAE 2 User’s Guide
2
Contents
1 Read Before Operating.................................... 1
2 Warnings ......................................................... 1
3 DoseRAE 2 Features ....................................... 5
4 General Information ........................................ 7
5 Charging The DoseRAE 2............................... 8
5.1 Charger/Reader....................................... 8
5.2 Removing The Silicone Boot ................. 9
5.3 Low Battery .......................................... 10
5.3.1 Charging With Instrument On ..... 11
5.3.2 Charging With Instrument Off..... 11
6 User Interface ................................................ 12
6.1 Display.................................................. 12
6.2 User Interface Icons.............................. 13
6.2.1 Advanced Version Icons.............. 14
7 Turning DoseRAE 2 On................................ 15
8 Turning DoseRAE 2 Off ............................... 16
8.1 Low-Voltage Shutoff............................ 16
9 Operation....................................................... 17
9.1 Normal Operating Mode....................... 17
9.1.1 Dose And Dose Rate.................... 19
9.1.2 Dose Alarm Value ....................... 23
9.1.3 Dose Rate Alarm.......................... 25
9.1.4 User ID......................................... 27

DoseRAE 2 User’s Guide
3
9.1.5 Clock/Calendar ............................ 27
9.1.6 Ambient Temperature .................. 28
9.2 Programming Mode.............................. 28
9.2.1 Entering Programming Mode ...... 29
9.2.2 Navigating Programming Mode .. 32
9.2.3 Alarms & Datalog Mode.............. 32
9.2.4 Dose Alarm Value ....................... 37
9.2.5 Dose Rate Alarm Value ............... 38
9.2.6 Clock & Calendar ........................ 40
9.2.7 Countdown Time ......................... 45
9.2.8 User ID......................................... 47
9.2.9 Dose Unit ..................................... 48
9.2.10 Display ......................................... 49
9.2.11 Temperature Unit......................... 50
9.2.12 End............................................... 51
10 ProRAE Dosimeter Software.................... 52
10.1 Overview .............................................. 52
10.2 Requirements........................................ 52
10.2.1 Hardware Requirements............... 52
10.2.2 Software Requirements................ 53
10.3 Installation ............................................ 53
10.3.1 USB Driver Installation ............... 59
10.3.2 Accessing The User’s Guide........ 61
10.4 Using ProRAE Dosimeter Software ..... 61

DoseRAE 2 User’s Guide
4
10.4.1 Connecting The DoseRAE 2
Charger/Reader To A Computer .. 62
10.5 Software Operation............................... 63
10.5.1 Open Datalog ............................... 65
10.5.2 Link Setting.................................. 66
10.5.3 System Options ............................ 67
10.5.4 Help.............................................. 69
10.5.5 Instrument List Window .............. 69
10.5.6 User Configuration ...................... 71
10.5.7 Changes And Safeguards ............. 74
10.5.8 Global Instrument Information .... 76
10.5.9 Alarm/Warning Percent ............... 76
10.5.10 Interval/Mode .......................... 78
10.5.11 Diagnosis ................................. 80
10.5.12 Current Readings ..................... 83
10.5.13 Command Buttons ................... 83
10.5.14 Firmware Version.................... 86
10.5.15 Read Event Headers ................ 87
10.5.16 Selecting An Event .................. 90
10.5.17 Datalog Buttons ....................... 92
10.6 Exiting ProRAE Dosimeter ................ 105
11 DoseRAE 2 Technical Specifications ..... 106
12 Technical Support ................................... 108
13 RAE Systems Contacts ........................... 109

DoseRAE 2 User’s Guide
5
3 DoseRAE 2 Features
Front View
LED alarm
MODE key Buzzer
Sensor
Location
SET key LCD
Rear View
Charger/Reader
contacts Cli
p
Short list o
f
instructions

DoseRAE 2 User’s Guide
6
Protective Pocket Wearing Option
Pocket clip
Protective
Pouch
Pocket Clip Wearing Option
Pocket clip
attached
directly to
DoseRAE 2

DoseRAE 2 User’s Guide
7
4 General Information
The DoseRAE 2 personal dosimeter is a thin
electronic monitor that can directly read X-ray or
Gamma-ray dose equivalent and dose equivalent
rate. It is specially designed for use in nuclear power
plants, nuclear fuel and nuclear components
factories, and nuclear waste-processing plants, as
well as in radiation source management, nuclear
medicine, and environmental monitoring
organizations. DoseRAE 2 has dual-channel
detectors that employ a semiconductor diode and a
scintillation crystal as sensors. It can detect radiation
rapidly in a wide range, and its energy compensation
ensures accurate readings.

DoseRAE 2 User’s Guide
8
5 Charging The DoseRAE 2
Charge the DoseRAE 2 before its first use, and
charge it when it is not in use. The DoseRAE 2 must
be placed in its Charger/Reader for battery charging.
5.1 Charger/Reader
The DoseRAE 2 Charger/Reader can be used for
DoseRAE 2 battery charging, parameter modification
and datalog reading (when connected to a computer
running ProRAE Dosimeter software). It can provide a
DoseRAE 2 with up to 100 mA of current. The
minimum charging time is 1.5 hours.
The red LED indicates the USB power supply is on
(Power). The green LED indicates the data
transferring is on (Status).
USB
Connector Green Status
LED
Red Power
LED

DoseRAE 2 User’s Guide
9
The DoseRAE 2 Charger/Reader can be plugged
directly into a computer’s USB port, or an extension
USB cable can be employed between the Charger/
Reader and the computer if plugging directly into the
port isn’t convenient. (For information on connec-
ting the Charger/Reader to a computer, refer to page
62.)
5.2 Removing The Silicone Boot
If the boot is installed, it must be partially removed
in order to expose its electrical contacts to meet with
the corresponding contacts in the Charger/Reader.
Pull down on the bottom of the boot and stretch it,
pulling it partially off of the DoseRAE 2. Release it, and
it stays out of the way of the contacts.
Boot
Release
Pull
Back
Stretch

DoseRAE 2 User’s Guide
10
Then place the DoseRAE 2 in the Charger/Reader.
After the battery is charged, reverse the process to
stretch the boot back over the DoseRAE 2.
5.3 Low Battery
When the battery voltage is low, the green LED
flashes once per minute and the LCD displays the
“battery low” icon:
After 12 hours in the “battery low” state, the instru-
ment automatically shuts off. Recharging is needed
after the instrument has automatically shut off.

DoseRAE 2 User’s Guide
11
5.3.1 Charging With Instrument On
During charging, the DoseRAE 2’s green LED flashes
once per second and the LCD displays the battery voltage
change:
When the battery is fully charged, the green LED
stops flashing, and the LCD displays the “battery
full” icon:
5.3.2 Charging With Instrument Off
While the battery charges, the green LED flashes
once per second and the LCD displays this:
When the battery is fully charged, the green LED
stops flashing and the LCD displays this:

DoseRAE 2 User’s Guide
12
6 User Interface
The DoseRAE 2’s user interface consists of an LCD
display, LED alarm, buzzer alarm, and [MODE] and
[SET] buttons. The display provides visual feedback
that includes time, functional mode, battery
condition, and radiation measurements.
6.1 Display
User interface icons employed on the display are
described on the next page.

DoseRAE 2 User’s Guide
13
6.2 User Interface Icons
Icon Indication
Battery status
Datalog history
Alarm: sound, light, vibration
Clock and countdown
Month(
user ID
M), Date(D), Year(Y) and
(ID)
Celsius
Fahrenheit
Dose
Dose rate
Error warning
Dose or Dose Rate alarm
mrem/h, rem/h
Dose rate rem unit: µrem/h,
Dose rate Sievert unit: µSv/h,
mSv/h, Sv/h
Dose rate Roentgen unit: µR/h,
mR/h, R/h
Display: 4 digits, 8 segments
Battery voltage

DoseRAE 2 User’s Guide
14
Over load
Low-channel sensor failure
High-channel sensor failure
Stand-alone mode
System control mode
Countdown time
Dose alarm value
Dose rate alarm value
User ID
Clock/Calendar
6.2.1 Advanced Version Icons
The following e Advanced
Version of the
Icon
icons are only found on th
DoseRAE 2:
Indication
Wireless communication
Shallow dose equivalent or dose
rate
Deep dose e
quivalent or dose rate

DoseRAE 2 User’s Guide
15
7 Turning DoseRAE 2 On
Press and ld conds. As
DoseRAE s inates
and checks the display
then chec s th mode, startup, and
firmware ers a 30-second
countdown. After the countdown, the reading
display is sho rmal detection.
ho the [MODE] button for 5 se
2 tarts up, the LCD screen illum
segments and backlight. It
e display, workingk
v ion before performing
wn and it begins no
The normal d
value.
isplay shows the accumulated dose

DoseRAE 2 User’s Guide
16
lues:Press [SET] to see the background dose rate va
8 Turning DoseRAE 2 Off
With the DoseRAE 2 in normal detection mode,
press and hold [MODE] for five seconds. There is a
five-second countdown, and when it reaches 0, the
word “OFF” is displayed. Release [MODE], and the
display goes blank in three seconds.
8.1 Low-Voltage Shutoff
When the battery voltage is lower than 3.3V in
normal detection mode a there are no alarm ,
the DoseRAE 2 shuts off a atically after 12
hours. It must then be recharged before it is used
again.
nd if s
tomu

DoseRAE 2 User’s Guide
17
oseRAE 2 has two operating modes:
•Normal Operating Mode
•Programming Mode
e unit
2 measures
amma radiation dose rate and accumulates readings
quentially step
h
it
ack to the first item in the list (this is
dicated in the table on the next page by the thick,
dark line with an arrowhead).
9 Operation
D
Normal Operating Mode is the default. After th
is turned on, it is in Normal Operating Mode.
Programming Mode is described on page 28.
9.1 Normal Operating Mode
In Normal Operating Mode, DoseRAE
g
for dosage data. Press [MODE] and se
through all functions. Press [SET] to step throug
the sub-functions.
Note: When you reach the last function or setting,
loops b
in

DoseRAE 2 User’s Guide
18
de Functions
Function
Normal Operating Mo
SET
MODE
Dose &
e Rate Dose Do
Dos se rate Clear dose
（hold 5 S）
Co
Tiuntdown me Countdown time ------ -----
Do
Alarm s
se et Pre-alarm Alarm -----
value value
value
Do
Al
va
se Rate
arm set
lue
Pre-alarm
value Alarm value -----
User ID User ID ------ -----
Cl
Calendar
ock/ Clock Month
& Date Year
Am
te
at
bient
mper-
ure
Show current ambient
temperature