Raidon SafeTANK GR3660-TB2 User manual

SafeTANK
User Manual
GR3660-TB2

» GR3660-TB2 User Manual.................................................................... 1
» GR3660-TB2 產品使用說明 ................................................................... 6
GR3660-TB2 User Manual
V 1 . 1

GR3660-TB2 User Manual
1
Table of Contents
1. Operating Information
The Introduction
Thanks for purchasing RAIDON product. This User Manual will introduce you the GR3660-TB2
Thunderbolt storage product. Before using your GR3660-TB2, please read it thoroughly. Although
all information contented in this User manual had already been carefully veried before publishing,
however, the actual product and its specification will be based upon the time of delivery from
RAIDON. Any update to the product or its relevant information may be listed on www.raidon.com.tw .
Product is subjected to change without notice.
If you have any question regarding this product, or you would like to know the latest product
information, or updates, please contact your local supplier or visit to www.raidon.com.tw for
assistance.
Copyright © RAIDON Technology, Inc. – All right is reserved.
Operating Temperature: 10 ～35 ℃(50 ～95 ℉)
Storage Temperature : -20 ～47℃(-4 ～116 ℉)
Line Voltage : 100 ～240V AC
1. Operating Information
2. Package Contents and product Views
3. Hardware Requirements and Precautions
4. Hardware Installation
5. RAID Modes and How to Switch between the RAID Modes
6. The Indication of HDD Status
7. Frequently Asked Questions

GR3660-TB2 User Manual
2
2. Package Contents and Product Views
Open the package and you shall nd the following parts：
Please make sure that the contents listed above are not damaged or missing. If you find any
damaged or missing parts in the package, please contact your supplier immediately.
GR3660-TB2
GR3660-TB2 Product Unit x1(Removable Tray x2)
Thunderbolt Cable x1
Power Cord x1
AC/DC Adapter x1
Foot Pad x4
CD x1
Screws & Keys
Quick Installation Guide x1
Front and Rear Views
A. HDD Status Indicator
B. HDD tray key lock
C. Power Switch
D. Power Socket
E. Thunderbolt Connector
F. RAID Dip-switch
G. Hidden Reset Button

GR3660-TB2 User Manual
3
3. Hardware Requirements and Precautions
1. Since GR3660-TB2 will delete all data les in your two HDDs/SSDs at its rst-time use, please
rst save all your personal data les before start using your new GR3660-TB2.
2. Please make sure that all hard drives have no badsectors nor defects prior to install them into
GR3660-TB2.
3. When turn o󰀨 or depart your GR3660-TB2 from your computer system, please remove GR3660-
TB2 shown as a device in your operating system rst.
4. When your GR3660-TB2 connects to a computer system, please do not remove, insert or swap
any hard drives while data transfer is being performed and the status indicators are flushing.
5. WARNING: If you plan to delete or change your original RAID setting, please always duplicate
your personal data before deleting or changing it.
6. GR3660-TB2 uses a 12V/5A AC/DC Adapter. Please do not use other non-certified Power
Adapterto avoid jeopardizing your GR3660-TB2 unit.
7. We strongly recommend you to keep an extra copy of your important personal data in a safe
place other than in your GR3660-TB2. Stardom will not be responsible of your data loss problem.
4. Hardware Installation
Please follow the instructions below to complete the hardware installation.
Use the provided key in the Accessories Kit and insert it into the Key Access to eject the Tray
Latch handle and the handle can be used to extract the tray.
Mount your hard drives with the screws included onto the removable drive tray and secure it
to avoid any damage to the hard drive.
After installing two HDDs into Trays, please insert them into GR3660-TB2, and then latch
the handle.
Please switch RAID Dip-switch to JBOD mode at back-plate.
Please connect the Thunderbolt Cable, and then connect AC/DC Adapter to the product.
Please turn on power.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6

GR3660-TB2 User Manual
4
5. RAID Modes and How to Switch between the RAID Modes
A. Please clear the RAID setting and format your two used HDDs before starting using your new
GR3660-TB2.
B. Please keep a copy of all your personal data into a safe storage space before set RAID mode at
your GR3660-TB2 unit.
C. JBOD (Factory defaults): Two independent storage volumes with no data protection feature.
D. RAID-1:
One independent data storage with data protection feature.
Other features:
• RAID 1 data protection feature is to duplicate all your data into the second HDD, and
GR3660-TB2 could still work in case if one of the HDDs becomes defect.
** GR3660-TB2 won’t help data protection if both HDDs are malfunction.
• If you use two di󰀨erent memory size HDDs, GR3660-TB2 will only matches the capacity of
the smaller capacity HDD.
** For example: if your two HDDs are with 1TB & 2TB memory capacity each, GR3660-TB2’s
maximum memory will be up to 1TB.
E. RAID-0: One big independent a storage with accelerated data transfer rate but with no data
protection feature.
F. The Standard Procedure to Switch RAID Setting
Step-1: Please rst connect GR3660-TB2 to your Mac with Thunderbolt cable..
Step-2: Please set RAID Dip Switch to the position you choose.
Step-3: Please use the Key to press the hidden RESET key at the back-plate, hold and wait
for the end of Blue-Purple LED blinking till a stable Blue light.
Step-4: Please turn o󰀨 your GR3660-TB2, and re-turn it on again. You now have reset
GR3660-TB2 with a new RAID mode successfully.
WARNING:
Please always duplicate your personal data before delete or switch back to your original RAID
setting.
Step 7
Step 8
a. After turning on power, the HDD/SSD Indicator will be changed with the following
sequence, Red > O󰀨 > Blue, and then, GR3660-TB2 is ready for use.
b. In case if the HDD/SSD Indicator shows Red > O󰀨 > Blue Flashing, please use a pin to
press the RESET Button for 3 seconds, and wait until the HDD/SSD Indicator is changed
to Blue from Blue Flashing, your GR3660-TB2 is then ready for use.
While your GR3660-TB2 is ready for use, please follow the instruction of "F. The Standard
Procedure to Switch RAID Setting" in Chapter 5 and set the RAID mode at your wish. You
could then start using your GR3660-TB2 now.

GR3660-TB2 User Manual
5
6. The Indication of HDD Status
Status LED Light Status
Power ON / No HDD Solid Red Light
Power ON / Two HDDs Solid Blue Light
Rebuilding, Source HDD Breathing Blue Light
Rebuilding, Target HDD Solid Purple Light
7. Common Technical Questions
1. GR3660-TB2 will always stay SLEEP Mode if (a) it doesn't connect it to a Mac Computer, and (b) your
Mac Computer is Power-O󰀨.
2. GR3660-TB2 will also stay SLEEP Mode if your Mac Computer gets into SLEEP or IDLE Mode.
3. In case you use two old HDDs which already have other RAID setting, we would strongly suggest
you to rst reset them rst at JBOD mode at your GR3660-TB2 before setting them to the other
RAID mode you use GR3660-TB2.

GR3660-TB2 User Manual
6
目錄索引
2. 產品外觀及包裝內容
1. 環境需求
關於這份手冊
感謝您使用 RAIDON 的產品。本手冊將介紹 GR3660-TB2 產品。在您開始使用 GR3660-TB2 產品前，
建議您先閱讀過本手冊。手冊裡的資訊在出版前雖已被詳細確認，實際產品規格仍將以出貨時為準；
任何產品規格或相關資訊更新請您直接到 www.raidon.com.tw 網站查詢，本公司將不另行通知。若您
想獲得 RAIDON 最新產品訊息、使用手冊、韌體 ,或對 RAIDON 產品有任何疑問，請您聯絡當地供應
商或到 www.raidon.com.tw 取得相關訊息。
本手冊相關產品內容歸銳銨科技股份有限公司版權所有
打開包裝外盒後，包裝內容應包含下列組件：
工作溫度 : 10 ～35 ℃(50 ～95 ℉)
儲存溫度 : -20 ～47℃(-4 ～116 ℉)
工作電壓 : 100 ～240V AC
請確認相關配件與產品本身是否有受損或配件缺少，若有任何疑問請與本產品供應商聯絡。
1. 環境需求
2. 產品外觀及包裝內容
3. 硬體需求與注意事項
4. 硬體安裝
5. 圖形介面面操作軟體
6. 硬碟狀態指示燈號說明
7. 常見問題
GR3660-TB2
GR3660-TB2 產品本體 x1( 內含抽取盒 x2)
Thunderbolt 連接線 x1
電源線 x1
電源轉換器 x1
腳墊 x4
CD x1
螺絲及鑰匙
快速安裝手冊 x1
» GR3660-TB2 產品使用說明

GR3660-TB2 User Manual
7
正面與背面示意圖
A. 硬碟讀取燈
B. 硬碟抽取盒把手
C. 電源開關
D. 電源埠
E. Thunderbolt 連接埠
F. RAID 切換鈕
G. Reset 鈕
3. 硬體需求與注意事項
1. 第一次使用本產品進行設定時，資料會被全數清除。請於硬碟置入前，確認硬碟已備份，避免資料
遺失。
2. 在安裝新硬碟到 GR3660-TB2 系列之前，請先確認硬碟是沒有壞軌而且是沒有故障的，以避免資
料受損。
3. 當您需要關閉或移除 GR3660-TB2 系列時，務必透過您所操作的作業系統中執行硬碟安全移除後，
方可進行電源關閉的動作。
4. 當系統運作時，請勿任意移除任何一顆硬碟，以免導致資料遺失。
5. RAID 模式一旦設定完成，若要進行切換，因切換過程中將會清除硬碟中的資料，請務必先將硬碟
中的資料另行備份後再行切換。
6. GR3660-TB2 使用 12V/5A 規格 Adapter，請勿使用其他非原廠規格 Adapter 以免損壞機器及資料。
7. 強烈建議除了使用 GR3660-TB2 系列的資料儲存功能外，請針對重要資料備份到另一個儲存裝
置上或遠端備份，雙重備份您重要的資料。若您儲存在 GR3660-TB2 系列的資料損毀或遺失，
STARDOM 將不負任何的責任。

GR3660-TB2 User Manual
8
4. 硬體安裝
5. RAID 設定
請參照以下步驟完成硬體安裝
請使用零件包內附的鑰匙插入鑰匙孔後，抽取盒門閂將會輕彈開啟，即可將硬碟機抽取盒取
出。
將硬碟安裝到抽取盒上，並以零件包內附的螺絲加以固定，以避免不必要的移動對硬碟造成
傷害。
硬碟安裝完成後，請將抽取盒平移放入主機內，並關上把手。
將硬碟安裝到抽取盒上，並以零件包內附的螺絲加以固定 ,以避免不必要的移動對硬碟造成
傷害。
將相關連接線接上，最後接上電源轉接器。
將機體背面的電源開關打開。
a. 機器啟動後，抽取盒燈號會由「紅燈恆亮 > 熄滅 > 藍燈恆亮」燈號，即為完成機器安裝設
定。
b. 如機器啟動後，抽取盒燈號如出現「紅燈恆亮 > 熄滅 > 藍紫閃爍」燈號，請使用頂針插入
「重置鍵」3秒後鬆開頂針，待燈號由「藍紫閃爍」燈號轉變為「藍燈恆亮」燈號時，即
為完成機器安裝設定。
機器安裝設定完成後，即可依需求設定 RAID 模式，請參考「RAID 設定 /F. 切換 RAID 設定
的標準程序」，做 RAID 模式切換設定。
步驟 1
步驟 2
步驟 3
步驟 4
步驟 5
步驟 6
步驟 7
步驟 8
A. 若使用的硬碟之前有在其他機器作過 RAID，請先確認 RAID 已清除並重新格式化完畢。
B. 切換任何 RAID 模式之前，請先行確認所有資料的備份在其他硬碟上。
C. JBOD（出廠預設值）：各別使用置入的硬碟存取空間。
D. RAID-1：兩顆硬碟進行同步寫入達到備份效果，其中一顆硬碟損壞仍可繼續運作，
將損壞硬碟更換新硬碟後將會自動進行資料重建 ; 當裝入的硬碟為 1大1小時，GR3660-
TB2 會將大容量的硬碟當成小容量的硬碟。
E. RAID-0：僅加速資料存取速度，對於資料備份不作任何保障。

GR3660-TB2 User Manual
9
6. 硬碟狀態指示燈號說明
7. 常見問題
1. GR3660-TB2 在開機情況下，未連接 Thunderbolt cable 時，風扇與電源指示燈皆為停止及休眠狀
態，直至連接 Thunderbolt cable 至電腦才會啟動風扇及電源指示燈。
2. 電腦進入睡眠模式時，GR3660-TB2 的風扇與電源指示燈皆為停止及休眠狀態，直至喚醒時才會啟
動風扇及電源指示燈。
3. 若硬碟已在其他磁碟陣列產品存取資料或設定 RAID MODE 過，建議還原成 JBOD 模式後再應用
於GR3660-TB2，以避免產生無法讀取硬碟問題。
狀態 硬碟狀態燈
電源開啟 / 無硬碟 紅燈恆亮
電源開啟 / 硬碟閒置 藍燈恆亮
Rebuilding-Source 呼吸燈（藍色）
Rebuilding-Target 紫燈恆亮
F. 切換 RAID 設定的標準程序：
步驟 1：請在 GR3660-TB2 連線到電腦後，一併打開電腦和 GR3660-TB2 的電源開關。
步驟 2：請在藍燈恆亮時，將在 GR3660-TB2 背板上設定 RAID 設定的「切換開關」調到你所
要的設定位置。
步驟 3：請使用頂針插入「重置鍵」，待前面板抽取盒上的閃爍藍紫燈結束、並轉成恆亮藍燈
後鬆開頂針。
步驟 4：請您再做一次關、開 GR3660-TB2 電源的動作後，您已經改變、並重新設定了 GR3660-
TB2 的RAID。
刪除或改變 RAID 設定的警告：
若您要刪除或改變任何 RAID 的設定，請先行備份硬碟內的所有資料，RAID 一旦刪除或改變亦即代表
資料已經被刪除。

www.raidon.com.tw