RAISE 3D E2 User manual

RaiseTouch E2 User Manual Date:03/03/2020
- 1 / 80 -
www.raise3d.com
RaiseTouch E2
User Manual

RaiseTouch User Manual Date:03/03/2020
- 2 / 80 -
www.raise3d.com
Contents
1.User Interface .................................................................................................................................................. 4
1.1 Home .................................................................................................................................................... 4
1.2 Tune ...................................................................................................................................................... 6
1.3 Utilities .................................................................................................................................................. 7
1.3.1 Move Axes ................................................................................................................................. 7
1.3.2 Filament Loader ........................................................................................................................ 8
1.3.2.1 Automatic Load...................................................................................................................... 8
1.3.2.2 Manual Load......................................................................................................................... 10
1.3.3 Levelling................................................................................................................................... 11
1.4 Print..................................................................................................................................................... 15
1.4.1 Uploading Queue ................................................................................................................... 15
1.4.2 Temp Task ............................................................................................................................... 16
1.4.3 Dashboard ............................................................................................................................... 17
1.4.4 Files management................................................................................................................... 20
1.5 Setting................................................................................................................................................. 22
1.5.1 Machine ................................................................................................................................... 22
1.5.1.1 Update .................................................................................................................................. 23
1.5.1.2 About .................................................................................................................................... 27
1.5.1.3 Hardware .............................................................................................................................. 28
1.5.1.4 Serial Port Log...................................................................................................................... 35
1.5.1.5 Privacy and Security............................................................................................................. 35
1.5.1.6 Advanced Settings ............................................................................................................... 43
1.5.1.7 Reset...................................................................................................................................... 46
1.5.1.8 RaiseCloud............................................................................................................................ 46
1.5.1.9 Developer ............................................................................................................................. 49
1.5.2 Camera..................................................................................................................................... 51
1.5.2.1 Camera Use .......................................................................................................................... 51
1.5.2.2 Time lapse............................................................................................................................. 53
1.5.2.3 Resolution and Frame Rate settings................................................................................... 54
1.5.3 Ethernet ................................................................................................................................... 55
1.5.4 WLAN....................................................................................................................................... 58
1.5.5 Other........................................................................................................................................ 60
1.5.5.1 Brightness ............................................................................................................................. 60
1.5.5.2 Language.............................................................................................................................. 60
1.5.5.3 Number of Nozzles.............................................................................................................. 61
1.5.5.4 Date and Time...................................................................................................................... 61
2. Operation...................................................................................................................................................... 62
2.1 Quick Settings .................................................................................................................................... 62
2.1.1 Enter from Home Interface .................................................................................................... 62
2.1.2 Enter from Utilities interface .................................................................................................. 64
2.2 Load .................................................................................................................................................... 65

RaiseTouch User Manual Date:03/03/2020
- 3 / 80 -
www.raise3d.com
2.3 Choose a file to print ......................................................................................................................... 66
2.4 Heat up extruder to profile temperature......................................................................................... 66
2.5 Pause and Stop .................................................................................................................................. 67
2.6 Finish the printing .............................................................................................................................. 67
2.7 Changing filament ............................................................................................................................. 68
2.8 Unload................................................................................................................................................. 69
2.9 Sequential Print Mode....................................................................................................................... 69
3. Printer Maintenance .................................................................................................................................... 71
3.1 Check Storage Space Before Operation .......................................................................................... 71
3.2 Maintenance....................................................................................................................................... 71
3.2.1 X Axis Level Up........................................................................................................................ 72
3.2.2 Offset Calibration.................................................................................................................... 72

RaiseTouch User Manual Date:03/03/2020
- 4 / 80 -
www.raise3d.com
1.User Interface
1.1 Home
The Home interface mainly introduces the relevant parameters of the printing file. Including:
L-Nozzle temp: The temperature of the left nozzle. Upper one is current temperature. Below one is
target temperature.
R-Nozzle temp: The temperature of the right nozzle. Upper one is current temperature. Below one is
target temperature.
Heatbed temperature: The temperature of the heatbed. Upper one is current temperature. Below one
is target temperature.
Home
Current: Click to read the name of the printing model.
Current

RaiseTouch User Manual Date:03/03/2020
- 5 / 80 -
www.raise3d.com
Time Est.: The total time and the remaining time of the printing model. The bigger one refers to the
remaining time. The small one below refers to the total time. Click the “Time Est.”to read the
estimated time.
Time Estimated
Percentage: The percentage of completed model.
Percentage

RaiseTouch User Manual Date:03/03/2020
- 6 / 80 -
www.raise3d.com
Height: The height of the completed model.
Press icon in the “Home” tab to switch the displayed information from completion percentage
based on total layers and layer count.
Height
1.2 Tune
The Tune interface shows the parameters associated with the movement of the printer. Including:
Tune
L-Nozzle temperature: The temperature of the left nozzle.
R-Nozzle temperature: The temperature of the right nozzle.
Heatbed temperature: The temperature of the heat bed.
Feed rate: Speed factor override percentage.
Fan speed: The speed of the fan which in controlled slot.
Note: Only the right lower fan on single-extruder machine can be controlled.
L-Nozzle flow rate: The flow rate of the left nozzle.
R-Nozzle flow rate: The flow rate of the right nozzle.

RaiseTouch User Manual Date:03/03/2020
- 7 / 80 -
www.raise3d.com
1.3 Utilities
“The Utilities”page is divided into three functional modules, Move Axes, Filament Loader and
Levelling. The position of the nozzle and heat bed can be adjusted on the Move Axes page. In the
Filament Loader page, you can Load/Unload filaments for left and right extruders. You can carry out
the flatness detection of the heat bed on the Levelling page.
Utilities
1.3.1 Move Axes
Nozzle selection: Select the nozzle that needs to be adjusted. “XL”represents for left nozzle; “XR”
represents for right nozzle; “Y”represents for hot bed; “Z”represents for screw rod fixing nozzles.
Unit Settings: The distance that the currently selected component moves each step. It can be set to 10
mm,1mm or 0.1 mm per step.
Travel range: XL travel range [-3,330mm], XR travel range [32,365], Y travel range [-3,240], Z travel
range [-3,240]
Click on the “XL”, a dialog box will pop up, asking you to enter the “XL absolute coordinates”. Enter
the value, XL will be automatically adjusted to the corresponding position. XR, Y and Z can be adjusted
the same way.
: Nozzle homing or Y axis homing (depending on whether the nozzle or Y axis is currently
selected).

RaiseTouch User Manual Date:03/03/2020
- 8 / 80 -
www.raise3d.com
: Z axis homing.
: Homing nozzles, heat bed and Z axis.
: Unlocking all motors. This sign is not a warning sign, If the X axis and Y axis are homed, the
extruders cannot be moved manually. Click the button to unlock the motor to remove the extruders.
1.3.2 Filament Loader
1.3.2.1 Automatic Load
Click “Filament Loader”on the left to enter the Filament Loader page, the Automatic Load page will
be displayed by default.
Automatic Load

RaiseTouch User Manual Date:03/03/2020
- 9 / 80 -
www.raise3d.com
Click on the red box area to enter the Filament Templates list. Please select the filaments template that
needs to be loaded or unloaded.
Template List
Click “+” icon on the top right corner of the interface to enter the filament template page. By default,
the system provides the template for Raise3D Premium PLA filaments, please modify the template
parameters as needed. Click “Save”to save template information.
New Template

RaiseTouch User Manual Date:03/03/2020
- 10 / 80 -
www.raise3d.com
1.3.2.2 Manual Load
Click the button to enter “Manual Load”page.
Click on the modify icon in the lower right corner of the temperature to modify the target temperature
and wait.
Manual Load 1
When the current temperature heats up to the target temperature, select the amount range that needs
to be extruded, and click the “Up”or “Down” button for extrusion or back pumping.
Manual Load 2

RaiseTouch User Manual Date:03/03/2020
- 11 / 80 -
www.raise3d.com
1.3.3 Levelling
Click “Levelling”to enter the levelling page, you can choose the Full Mode -63 points (9*7) levelling as
needed, or the Simple Mode -9 points (3*3) levelling.
Leveling
Select “Simply Mode”, the printer will automatically carry out 9-point levelling.
Simple Mode

RaiseTouch User Manual Date:03/03/2020
- 12 / 80 -
www.raise3d.com
Click to see the levelling results.
Leveling Results (3D)
indicates that the flatness of the heat bed is in the normal range and the printer can print
directly.
indicates that the flatness of the hot bed exceeded the normal range, which is needed to be
manually leveled first. (you can perform manual levelling according to the file How to Level the
Bed.pdf )
Click on the “2D”icon to switch to flat view to view levelling results.
Click on the green area coordinates below to show the height difference at the coordinates.
Leveling Results (2D)

RaiseTouch User Manual Date:03/03/2020
- 13 / 80 -
www.raise3d.com
Click to access the Auto levelling page.
Auto levelling
Turn on the Auto levelling, the printer will make automatic levelling before each printing.
Simple mode: In Simple Mode, the printer will flatten the whole printing plate by 9 points before each
printing.
Simple mode

RaiseTouch User Manual Date:03/03/2020
- 14 / 80 -
www.raise3d.com
Full Mode: In Full Mode, the printer will carry out 63-point levelling of the whole printing plate before
each printing.
Full Mode
Smart Mode: In Smart Mode, the printer will only level the area where the model is located before
each print.
Smart Mode

RaiseTouch User Manual Date:03/03/2020
- 15 / 80 -
www.raise3d.com
1.4 Print
On this page, you can view history print records, Uploading queue, and print model information.
Print
You can print in three ways below: Local Storage, SD card and USB.
1.4.1 Uploading Queue
Click on the “Uploading Queue”to view files uploaded through WLAN and Ethernet. Printing files can
be uploaded remotely from ideaMaker to the printer. Click the “Uploading Queue”to see the upload
file size, transmission speed, remaining time and upload percentage.
Uploading queue

RaiseTouch User Manual Date:03/03/2020
- 16 / 80 -
www.raise3d.com
Note: the file will be saved in local storage after uploading. Click the print file to enter the model
related information interface, where the parameter information of the model can be viewed.
Print Model Information
1.4.2 Temp Task
The temporary task interface allows to view the interrupted print task, where you can select the
unfinished print task to continue printing or reprint the file.
Temp Task

RaiseTouch User Manual Date:03/03/2020
- 17 / 80 -
www.raise3d.com
Power loss: when the printer is restarted or the serial port is reconnected, if the interrupted printing
task is detected, the print interface will pop up automatically to resume. Click “Recover current task”
to resume the printing Task. Click “Restart current task”to reprint the task. Click “Cancel current
task”to exit the interface. You can also continue the task through the Temp task after exiting.
Power loss
1.4.3 Dashboard
You can view all printed models on Dashboard. Click “Add Tag”, you can add labels for printed tasks.
The icon in the upper left corner of the print file queue shows the success or failure information.
Add Tag

RaiseTouch User Manual Date:03/03/2020
- 18 / 80 -
www.raise3d.com
Click on the top right corner, a box will pop up as shown in the figure:
Filter
You can filter printing task records by clicking on the “Cloud”, “Local Storage”, “USB”according to
the file source, while you can enter manually added labels for secondary screening. The screening
results are shown below:
Filter Results

RaiseTouch User Manual Date:03/03/2020
- 19 / 80 -
www.raise3d.com
Select the files in the list and print them if they are in readable format.
Printable files
Non-printable files

RaiseTouch User Manual Date:03/03/2020
- 20 / 80 -
www.raise3d.com
Timelapse: click the wrench icon in the “Setting>Camera” to enter the camera advanced settings
page. Turn on Timelapse, you can click video icon on the lower right corner of the Dashboard to view
the Timelapse video. Turn on the “Enable Exporting Local Files to External Storage” in Settings >
Security and Privacy, you can use USB devices to export Timelapse files. Export format is MP4 format.
Export Timelapse files
1.4.4 Files management
Click “Local Storage” to enter the print file interface, and click the “Edit” button in the upper right
corner to manage files.
Add: Click Add to create a new folder.
Copy: Select a file to be copied and click Copy to copy the file to another folder.
Move: Select a file you want to move and click Move to move the file to another folder.
Rename: Rename the selected file.
Delete: Delete the selected file.
Files Management