Raw Thrills Bust-a-Move Frenzy User manual

040-00074-01 REV 4
Bust-a-Move Frenzy ™
Operator’s Manual
© TAITO CORPORATION 1994, 2020 ALL RIGHTS RESERVED.
Software ©2020 Raw Thrills, Inc.

This Page Left
Blank
Intentionally

Bust-a-Move Frenzy ™
3 | P a g e
Table of Contents
Safety............................................................................................................................................................5
Operation..................................................................................................................................................5
Transporting..............................................................................................................................................5
Handling Components ..............................................................................................................................5
Disconnect Power .....................................................................................................................................5
Grounding .................................................................................................................................................5
Electrical Shocks........................................................................................................................................5
Power Selector..........................................................................................................................................5
Power Cord ...............................................................................................................................................5
Surge Suppressor ......................................................................................................................................5
Water and Other Liquid Sources...............................................................................................................6
Connectors................................................................................................................................................6
Computer..................................................................................................................................................6
Tempered Glass Warning........................................................................... Error! Bookmark not defined.
Hazard to Epileptics ..................................................................................................................................6
Manual......................................................................................................................................................6
Specifications ............................................................................................................................................6
Product Specifications..................................................................................................................................7
Electrical Power ........................................................................................................................................7
Temperature.............................................................................................................................................7
Humidity....................................................................................................................................................7
Dimensions................................................................................................................................................7
Fuse Replacement Guide .............................................................................................................................8
12V Power Distribution.............................................................................................................................8
Setup.............................................................................................................................................................9
Unpack Materials......................................................................................................................................9
LED Display Quick Set-up Guide................................................................................................................9
Required Tools: ...................................................................................................................................10
Parts Note: ..........................................................................................................................................10
Frame Components (Not to Scale):.........................................................................................................10
Quadrants and Marquee Components (Not to Scale):...........................................................................12

Bust-a-Move Frenzy ™
4 | P a g e
Marquee Power Supply: .........................................................................................................................14
Network Cable Connections: Deluxe (P7)...............................................................................................15
Cabinet Assembly....................................................................................................................................16
Card Reader Installation and Setup ........................................................................................................18
Check Electrical Settings .........................................................................................................................19
Startup Game..........................................................................................................................................19
Diagnostic and Adjustments ......................................................................................................................20
Basic Functional Test on Initial Power Up...............................................................................................21
Test Menus..............................................................................................................................................22
Main Menu..........................................................................................................................................22
Diagnostics..........................................................................................................................................23
Pricing and Payout Adjustments (Cash)..............................................................................................24
Pricing and Payout Adjustments (Tokens) ..........................................................................................25
Pricing and Payout Adjustments (Swipes) ..........................................................................................26
Game Settings.....................................................................................................................................27
System Settings...................................................................................................................................28
Audits ..................................................................................................................................................29
Resets Menu .......................................................................................................................................30
Volume................................................................................................................................................31
Calibration...........................................................................................................................................32
Utilities................................................................................................................................................33
Advertising ..........................................................................................................................................34
System Information.............................................................................................................................35
Choosing the Right Pricing Adjustments for Your Location....................................................................36
Advertising Menu User Guide.................................................................................................................37
PC Hardware ...........................................................................................................................................39
Fujitsu Mini BIOS.....................................................................................................................................40
PC Hard Drive Recovery ..........................................................................................................................41
Troubleshooting .........................................................................................................................................42
Technical Support.......................................................................................................................................49
Electrical and Mechanical Illustrations......................................................................................................51

Bust-a-Move Frenzy ™
5 | P a g e
Safety
Operation
Before operating game, read this manual. Failure to properly install and operate this game could result in
malfunction or accident. Operate the game in accordance with the manual.
Transporting
The cabinet is very heavy. Because the monitor is high, the cabinet is also very top-heavy. Use appropriate
care when moving or transporting cabinet. It contains fragile glass and electronic components. Avoid rough
handling.
Handling Components
Many components are extremely sensitive to handling, environmental and Electrostatic Discharge (ESD)
events—especially the computer. Do not handle it roughly. Before servicing, call your distributor and inquire
about the PC warranty. Use proper ESD procedures when servicing. Protect components from harmful
environmental conditions, such as extreme temperatures, excessive moisture or other damaging effects.
Disconnect Power
Always turn the power off and unplug the unit before servicing or making adjustments unless otherwise
instructed. Installing or repairing components while power is on can damage the components and void the
warranty.
Grounding
Avoid electrical shock. Do not plug in AC power until you have inspected and properly grounded the unit.
Only plug into a grounded, three-wire outlet. Do not use a “cheater” plug or cut off the ground pin on the line
cord.
Electrical Shocks
There is no isolation transformer in the cabinet. Disconnect AC power before servicing. However, be aware
that lethal voltages can remain in the electronic components even when AC power is disconnected. Use
extreme caution when servicing. Verify that there is a working ground connection. If the unit sustains water
damage, cease using it immediately and unplug AC power.
Power Selector
Before installing game, ensure the voltage on the PC and power supply is set properly. There is a 115/230
VAC selector switch that must be set for the correct voltage for your site. The setting must match the line
voltage at the installation site.
Power Cord
If the power cord is damaged or lost, replace it with an identical cord as supplied by the manufacturer or an
authorized service agent.
Surge Suppressor
It is recommended that you plug your game’s power cord into a surge suppressor to help protect from power
surges that may damage sensitive electronic components.

Bust-a-Move Frenzy ™
6 | P a g e
Water and Other Liquid Sources
Do not install game near sprinkler or other water jet sources. Do not use water jet to clean game. Keep
minimum clearance behind game and wall for proper ventilation but also prevent access of liquid from spills
and sprays from entering ventilation holes.
Connectors
When servicing machine, ensure all connectors mate properly. If connectors do not slip in easily, do not force
them. Connectors are often keyed and only connect one way. Check for correct orientation.
Computer
The computer contains sensitive components, including a hard drive. Do not handle it roughly. Call your
distributor before servicing its internal components. Ask about warranty information as it relates to the PC.
Cycle AC power on or off with the cabinet power switch.
A dongle has been inserted into one of the USB ports. This is required for game play.
Do not remove the dongle except for troubleshooting purposes.
Hazard to Epileptics
A small portion of the population has an epileptic condition that may cause seizures. Affected persons
experience seizure while watching some television pictures or playing certain video games. People who have
not had seizures may still have an undetected epileptic condition. If anyone in your family has experienced
epilepsy symptoms (seizures or loss of awareness), consult your physical before using video games. While
children play video games, a parent should observe. Be alert to the following symptoms: dizziness, altered
vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation or convulsions. If
you or your child experiences these symptoms, discontinue use immediately and consult your physician.
Manual
Keep this manual available and ready for use. If the game fails to function properly, turn off the machine and
unplug the AC line cord. Contact your local distributor. You may not reproduce this document or any of its
contents without written authorization from Raw Thrills, Inc.
Specifications
For reasons such as performance, this product’s specifications may change without notice. Federal patent,
copyright and other intellectual property laws protect the content, devices and design of the game and its
equipment.

Bust-a-Move Frenzy ™
7 | P a g e
Product Specifications
Electrical Power
United States, International and Japan
Operating AC Current: 5/2.5 Amps
Voltage: 115/230~ VAC 50/60Hz
Inrush AC Current: 5 Amps
Temperature
50° F to 104° F
(10° C to 40° C)
Humidity
Must not exceed 95% relative humidity
Dimensions

Bust-a-Move Frenzy ™
8 | P a g e
Fuse Replacement Guide
NOTE: FOR CONTINUED PROTECTION AGAINST FIRE AND ELECTRICAL DAMAGE, USE ONLY SPECIFIED FUSE
TYPE AND VALUE.
12V Power Distribution
Please see unit for specified fuse labeling.
Cabinet:
6x 5A 250V 3AG Slo-Blo Fuse (Littelfuse 0313005)
Gun Harness (each):
2x 2A 250V 3AG Slo-Blo Fuse (Littelfuse 0313002)

Bust-a-Move Frenzy ™
9 | P a g e
Setup
Unpack Materials
1. Place the shipping crate(s) on a flat, stable surface.
2. Cut the banding straps and remove the cardboard lids.
3. Lift off the large cardboard containers surrounding the cabinet assembly and remove any shipping
cleats.
4. Remove the coin door key from the coin return slot.
5. Open the top coin door.
6. Locate the keys for the back door and the cash box door.
7. Open the cash box door and remove the cash box.
8. Check for shipping damage to the following:
•Marquee and monitor
•Cabinet decals
9. Check the AC line cord for visible signs of damage.
Pay particular attention to the plug and line cord insulation.
LED Display Quick Set-up Guide
Important Note: This manual is accompanied by a separate document: “P7.62 LED Wall Assembly and
Service Document.” Please refer to this document when installing, servicing and troubleshooting the LED
display. It is a more comprehensive guide and provides more detail than the quick setup guide listed
below. Keep this and other documentation for future reference. Additional information regarding the
latest version of software and documents can also be found on our web site:
www.rawthrills.com

Bust-a-Move Frenzy ™
10 | P a g e
Listed below is a step by step process to assemble the LED Display for Bust-a-Move Frenzy™. For
additional assistance, reference the full Assembly and Service Procedure included with the game. 2
people are required to do the assembly. Ladders are recommended when assembling the top
quadrants of the LED screen. Refer to the “LED Wall Assembly and Service Document” for details.
Required Tools:
M6 Allen Key, #2 Phillips Screwdriver, and a Level
Parts Note:
All parts are labeled with decals. Refer to these decals when assembling the screen.
Frame Components (Not to Scale):
1 –Left Base Assembly (x1)
2 –Right Base Assembly (x1)
3 –Left Upper Tube Assembly (x1)
4 –Right Upper Tube Assembly (x1)
5 –Cross Tube (x4)
6 –M8x16mm Socket Head Cap Screw (x24)

Bust-a-Move Frenzy ™
11 | P a g e

Bust-a-Move Frenzy ™
12 | P a g e
VIEW FROM BACK
Quadrants and Marquee Components (Not to Scale):
7: Marquee Assembly (x1)
8: Marquee Power Supply (x1)
9: 4x9 Display Quadrant (x2)
10: 3x9 Display Quadrant (x2)
11: Center Planar Bracket (x1)
12: Side Planar Bracket (x4)
13: M5x8mm Phillips Head Screws (x8)
14: M8x16mm Socket Head Cap Screw (x16)

Bust-a-Move Frenzy ™
13 | P a g e
(Note- Install screen quadrants individually)

Bust-a-Move Frenzy ™
14 | P a g e
Marquee Power Supply:

Bust-a-Move Frenzy ™
15 | P a g e
Network Cable Connections: Deluxe (P7)

Bust-a-Move Frenzy ™
16 | P a g e
Cabinet Assembly
1. Using above diagram as a guide install lower sign using Phillips bit with supplied (4) M5 X
12mm screws. To secure cinch brackets to tubes, be sure to remove protective backing from
double sided foam tape.
2. Place control (gun) cabinet in front of LED display.
3. Locate the two connecting brackets and the following hardware: (6) black tamper proof Torx
machine screws, ¼-20 thread, 2” long, and (6) ¼” black split lock washers, and (6) ¼” black
flat washers. Using a T-27 bit, attach these connecting brackets to the inside of each cabinet
side as shown in the cabinet assembly setup diagram.
4. Move pedestal assembly in front of control (gun) cabinet and connect harness. Locate the
following hardware: (6) black tamper proof Torx machine screws, ¼-20 thread, 2” long, and
(6) ¼” black split lock washers, and (6) ¼” black flat washers. Push cabinet halves (seat and
gun section) completely together and be sure not to pinch wire harness. Using T-27 bit,
connect the two cabinet halves with the hardware as shown in the cabinet assembly setup
diagram.
5. Locate the following hardware: (2) black tamper proof Torx machine screws, ¼-20 thread, 1
½” long, and (2) ¼” black split lock washers, and (2) ¼” black flat washers. Install screws
through pedestal floor to center connecting bracket.
6. Move the completed cabinet assembly into the desired position in front of the display. Raw
Thrills recommends a minimum distance of 100 inches total depth from back of LED wall
base legs to the back of the seats.

Bust-a-Move Frenzy ™
17 | P a g e
7. Connect the provided network cable between the back of the completed cabinet at the terminal
near the on/off switch and the back of the LED wall assembly. Use supplied D-channel sleeve
and carpet tape to properly dress the network cable on the floor.
8. Attach Marque Power Supply to frame and plug in the connector from marquee to marquee
power supply.

Bust-a-Move Frenzy ™
18 | P a g e
Card Reader Installation and Setup
Due to the rising popularity of aftermarket debit card systems for cashless or coinless operation of
amusement machines (i.e. Embed, Intercard, Semnox), this NERF™ Arcade cabinet is equipped with UCL
compatible harnessing to ensure that the installation process is easier and less prone to miswiring.
You can choose to use 1 or 2 card readers in the pricing adjustments section of the test menu. It is
recommended to use 2 card readers for best results and player access.
There are (2) supplied connections, each located under the control panel near the player positions.
There is enough slack to accommodate mounting (2) card readers on the control panel, or on the front
panels, as each operator desires.
If only (1) card reader will be used, it is recommended that the card reader be mounted to the coin door
using either the provided UCL connector.
UCL, or Universal Card Link, is a debit card standard established by the American Amusement Machine
Association. Visit https://coin-op.org/standardization/ for the latest UCL standard and manual
information.
The UCL connections on the game use pins 1, 2, 6, 8, and 9. The other pins are unused. Each UCL
connector can supply up to 1A at 12VDC.

Bust-a-Move Frenzy ™
19 | P a g e
Check Electrical Settings
1. Verify the voltage in the nearest AC outlet.
2. Verify the AC outlet ground connection is present and working.
Startup Game
1. Plug the line cord into an AC outlet.
2. Turn the main cabinet power switch on.
3. Verify the game and all components are operating normally. See Basic Functional Test on Initial
Power Up in the Diagnostics and Adjustments section for the recommended procedure.

Bust-a-Move Frenzy ™
20 | P a g e
Diagnostic and Adjustments
The Service Button Panel has four buttons, three of which can navigate the menu system.
The control panel buttons and joysticks/guns can also advance through test menu screens.
Navigating the Test Menu
Button
Action
TEST (Not in Test Menu)
Enters Test Menu
TEST (In Test Menu)
Selects Highlighted Option
SERVICE (On Main Menu)
Exits Test Menu
SERVICE (Not on Main Menu)
Cancels Selection
VOLUME UP
Move Up
VOLUME DOWN
Move Down
Start Buttons
Selects Highlighted Option
An on-screen message acknowledges changes or when you exit a selection without making a change.