real living 5838-7037-GM User manual

GUNMETAL FINISH MESH SHOE
RACK OVER THE DOOR
ASSEMBLY INSTRUCTION
SKU#: 810605446
Made in China
©Whitmor, Inc
Need help? We are here for you! 1(888)944-8667 • Toll Free
ITEM#: 5838-7037-GM

Read all instructions before starting.
Clear a flat covered space to begin.
Always best to do it with a friend.
Note that hardware required is provided for every step.
Pay attention to orientation.
Assemble on soft, smooth surface to protect finish from being scratched.
Do not overload the unit.
Regularly check hardware and tighten if necessary.
Wipe clean with a damp cloth when necessary.
No additional tools required if hanging over the door.
Hex wrench provided.
For wall mounting, a drill and Phillips screwdriver are required.

x14
Horizontal Poles Middle Vertical Frames
x2
Top Vertical Frames
with Push Tab
A B
D
C
E
K
J
I
F
H
PARTS LIST
Part Reference
A
B
C
D
E
F
G
H
I
J
F11516
F11517
F11518
F11519
F11520
F11521
F11522
F11523
F11524
F11525
x4
x2
Bottom Vertical Frames
x28
Hex Screws
x2
Over the Door Brackets
x1
Mesh Shelves
x1
Hex Wrench
x4
Wall Screws
x4
Wall Anchors
NOTE: Part (J) is for optional
mounting of frame.

x1 x1
CD
x13x1
E
F
x1
I
A A A A A A A A A
A
E E E E E E
E
Place one of each frame sections (C,D) and two of middle frame section (B) on a flat hard
surface and clip together with the push tabs. Attach thirteen horizontal poles (A) to frame sections
using thirteen hex screws (E). Tighten with hex wrench (I). Install over the door bracket (F) by sliding
onto the top vertical frame pole (C) past the first hole.
x13 x2
A
C
B
Assembled View:
F
A A A A A A
EEE E E E
B B D
TOP
BOTTOM
STEP 1

Attach remaining horizontal pole (A) and hex screw (E) behind the bracket (F). Tighten with hex wrench (I).
Unfold the mesh shelves (H) and install onto horizontal poles. Make sure the tag on the mesh shelves (H) is
at the top of the unit.
Assembled View:
x1
E
x1
A
x1
H
x1
I
H
E
C
TOP
BOTTOM
STEP 2

A A
x1 x1
CD
x14 x1
EF
x1
I
x14 x2
AB
F
E
E E E E E E E E E E E
E
E
CB B D
A
A A A A A A A A A A A A
H
Clip together remaining frame sections (B,C,D) with the push tabs. Install over the door bracket (F) by
sliding onto the top vertical frame pole (C) past the first hole. Align assembled side frame section with
horizontal poles (A) and attach using hex screws (E). Tighten with hex wrench (I).
A
TOP
BOTTOM
STEP 3

Lift the assembled shoe rack and place over an interior door.

F
Break off the top of over the door bracket (F)
perforation. Use a drill (not included) to pre-drill
holes if you are installing this shoe rack onto drywall
or soft wall. Insert wall anchors (K). Use a Phillips
screwdriver (not included) to tighten
screws (J) into wall.
J
F
J
J
K
K
K
x4
J
x2
F
x4
K
F
K
J
F
J
J
K
K
F