real living BL-TV-052-20A User manual

GENERAL BEST PRACTICES FOR ASSEMBLY:
WARNINGS:
Page 1 of 13
MAINTENANCE:
Wipe with a damp cloth. Use Furniture polish or lemon oil on the wood as needed.
Avoid prolonged exposure to moisture.
Do not scratch or chip the finish.
Do not put hot objects which are more than 80 degrees Fahrenheit directly on the surface.
Check bolts/screws periodically and tighten if necessary.
To prolong the life of product we recommend storage in a dry area when not in use
or during austere weather conditions.
Should this product become damaged, and/or components are broken or missing,
DO NOT USE.
This product will burn if left in contact with flame source.
To prevent serious injury or death, this product is equipped with a wall anchoring system.
Before this product can be used, the wall anchoring system must be installed as directed in
the assembly instructions.
WARNING: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
WARNING - Death or serious injury may occur when children climb on audio and/or video
equipment furniture. A remote control or toys placed on the furnishing may encourage
a child to climb on the furnishing and as a result the furnishing may tip over on to the child.
WARNING - Relocating audio and/or video equipment to furniture not specifically designed
to support audio and/or video equipment may result in death or serious injury due to the
furnishing collapsing or over turning onto a child.
Determine you have adequate space for assembly.
Assembly by two adults is recommended.
Assemble on soft surfaces to prevent damage to product finish.
Keep children away during assembly. This item contains small parts which can be
swallowed by children.
Do not discard any of packaging until you have checked that you have all parts and hardware.
Retain the assembly instructions for future reference.
The manufacturer will not accept responsibility for unauthorized repairs or modifications to
this product.
This product is for residential use only, not for commercial use.
A Phillips head screwdriver is necessary for assembly but is not included.

PARTS LIST
Page 2 of 13
x 1 pc
Top panel
x 1 pc
AB
x 1 pc
C
Left Side Panel Left Middle Panel
x 1 pc x 1 pc
DE
x 1 pc
F
Right Side Panel Left Door
x 1 pc
Right Door
x 2 pcs
GH
x 1 pc
I
Side Back Panel Center Back Panel
Right Middle Panel

PARTS LIST
Page 3 of 13
x 2 pcs
Center Adjustable Shelves
x 2 pcs
JK
x 1 pc
L
Bottom Panel
x 1 pc
Bottom Crossbar
x 8 pcs
MN
Connect Wood
Side Adjustable Shelves

HARDWARE LIST
3
2
4
Wood Dowel Ø8*30mmL
x 16 pcs
5 6
7
Hinge Screw Ø7*16mmL
x 24 pcs
Knob Bolt
Ø5/32"*25mmL
x 2 pcs
Knob
x 2 pcs
Shelf Pin
x 16 pcs
Screw Ø8*28mmL
x 4 pcs
8
10
9
11 12
15
Page 4 of 13
1
Anti-Tipping Strip 25*230mmL
x 2 pcs
Wall Anchor
Ø8.5*30mmL
x 2 pcs
13 14
Hinge
x 4 pcs
Screw Ø7*19mmL
x 8 pcs
Plastic Block 30*14*8mm
x 8 pcs
Flat Washer Ø1/4"*16mmW*1mmT
x 40 pcs
Spring Washer Ø1/4"*1mmT
x 36 pcs
Allen Bolt Ø1/4"*32mmL
x 36 pcs
Allen Key 4mm
x 1 pc

STEP 1
Hardware needed
Page 5 of 13
Assembled View:
x4 x4
x1
1
2
3
4
With assistance, place the Bottom Panel (L) upside down on a
smooth surface. Attach the Bottom Crossbar (M) to Bottom Panel (L)
with Flat Washer (3), Spring Washer (2) and Allen Bolt (1) using
Allen Key (4).
Fully tighten all bolts.
Return Bottom Panel (L) to upright position.
x4
1
2
3
4
L
M

x16 x16
x1
Hardware needed
1
2
3
4
Place the Left Side Panel (B) upside down on a smooth surface.
Align the holes in Connect Wood (N) with the holes in Left Side Panel (B)
as shown. Secure Connect Wood (N) to Left Side Panel (B) with Flat
Washer (3), Spring Washer (2) and Allen Bolt (1) using Allen Key (4).
Note: The Connect Wood (N) should be flush with the edges of the panels.
Repeat the process to attach Connect Wood (N) to Right Side Panel (E),
Left Middle Panel (C) and Right Middle Panel (D).
STEP 2
Page 6 of 13
Assembled View:
N
N
N
N
N
N
N
x16
E
B
C
D
1
2
3
4
N

STEP 3
Hardware needed
Page 7 of 13
Assembled View:
x8 x8
x1
1
2
3
4
x8
x8
5
Insert Wood Dowel (5) into Bottom Panel (L). Align the holes
in Right Side Panel (E) with the inserted Wood Dowels (5)
and slide to place. Secure Right Side Panel (E) to Bottom
Panel (L) with Flat Washer (3), Spring Washer (2) and Allen
Bolt (1) using Allen Key (4). Fully tighten all bolts.
Repeat the process to attach Left Side Panel (B), Left Middle
Panel (C) and Right Middle Panel (D) to Bottom Panel (L).
1
2
3
4
5
B
C
D
E
L

STEP 4
Page 8 of 13
Assembled View:
Hardware needed
x8 x8
x1
1
2
3
4
x8
x8
5
Open Center Back Panel (I). Insert Center Back Panel (I)
down along the groove of Left Middle Panel (C) and Right
Middle Panel (D). Insert Side Back Panel (H) down along
the groove of Left Side Panel (B) and Left Middle Panel (C).
Repeat the process for the remaining Side Back Panel (H) to
attach to Right Side Panel (E) and Right Middle Panel (D).
Insert Wood Dowel (5) into holes on the edge of Left Side
Panel (B), Left Middle Panel (C), Right Middle Panel (D) and
Right Side Panel (E). With assistance, align the holes in Top
Panel (A) with the inserted wood dowels and lower into place.
Attach Left Side Panel (B), Left Middle Panel (C), Right Middle
Panel (D) and Right Side Panel (E) to Top Panel (A) with
Flat Washer (3), Spring Washer (2) and Allen Bolt (1) using
Allen Key (4). Fully tighten all bolts.
I
5
A
I
H
H
1
2
3
4

STEP 5
Page 9 of 13
Hardware needed
x4 x24
x2 x2
Attach Hinge (8) to Right Door (G) with Hinge Screw (9) using
Phillips head screwdriver. Fully tighten screws.
With assistance, center the Right Door (G) along the edge of Right
Side Panel (E). Attach Hinge (8) to Right Side Panel (E) with Hinge
Screw (9). Fully tighten screws. Repeat the process to attach the
Left Door (F) to the Left Side Panel (B).
Attach Knob (11) to Right Door (G) with Knob Bolt (10).
Fully tighten bolts.
Repeat the process to attach remaining handle to Left Door (F).
Assembled View:
Not included
89
10 11
FG
89
11
10
9G

STEP 6
Page 10 of 13
Assembled View:
x16
12
Insert the Shelf Pin (12) into the pre-drilled holes as shown in the
diagram. Place Adjustable Shelf (K) onto the Shelf Pins as shown.
Repeat the process for the remaining Adjustable Shelf (K) and the
Center Adjustable Shelves (J).
You can adjust the position of shelf as needed. Place the Plastic
Block (6) into the corner of Side Back Panel (H) as shown. Insert
Screw (7) into the pre-drilled holes and secure with Phillips
Screwdriver. Fully tighten screws.
Repeat the step for the remaining Plastic Block. Insure all Plastic
blocks are used to secure both side back panels in place.
Hardware needed
Not included
67
x8 x8
K
K
J
12
K
66
7
H
H

STEP 7
Hardware needed
x4 x2
3
x2 x4
Not included
Attach the Anti-tipping Strips (13) to the back top of the mantel with
Screw (15) and Flat Washer (3). With assistance, place the console
in the desired location and mark the wall just below the spot where
the Aniti-tipping Strips are attached to the console.
Remove the console.
Drill holes in the marked locations on the wall and insert the Wall
Anchor (14). Place the console back into position leaving room to
attach the Anti-tipping Strips (13) to the Wall Anchor (14) with Screw
(15) and Flat Washer (3). Fully tighten Screws.
Move the console tight against the wall.
NOTE:
Please insure any media equipments is plugged in and working
correctly before securing the Anti-tipping Strips to the Wall Anchors.
NOT INCLUDED
NOT INCLUDED WALL
WALL
WALL
NOT INCLUDED
NOT INCLUDED
13
14
3
15
3
15
13
Page 11 of 13
Assembled View:
13
14 15

WARNING
The maximum diagonal Plasma/LCD television screen size is 52inch (132.08cm).
For use with televisions weighing 135 lbs. (61.23 kg) or less. Using larger or
heavier televisions may cause instability or tip-over which lead to serious injury
or even death.
WARNING - Death or serious injury may occur when children climb on audio
and/or video equipment furniture. A remote control or toys placed on the furnishing
may encourage a child to climb on the furnishing and as a result the furnishing
may tip over on to the child.
WARNING - Relocating audio and/or video equipment to furniture not specifically
designed to support audio and/or video equipment may result in death or serious
injury due to the furnishing collapsing or over turning onto a child.
GRAND ART FURNITURE CO., LTD
ADDRESS: D17 STREET, MY PHUOC I INDUSTRIAL PARK,
BEN CAT DISTRICT, BINH DUONG PROVINCE, VIETNAM
Page 12 of 13
MAXIMUM LOAD 135LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS

PRINTED IN VIETNAM
ASSEMBLY IS COMPLETED
Page 13 of 13