real living FP-P-1915-32 User manual

1. Need at least two adults to assemble this fireplace.
2. Assemble on soft , smooth surface to protect finish from being scratched.
3. DO NOT use power tools.
4. Remove all packaging material, make sure all parts are present before assembly.
5. Estimated Assembly Time: 1 hour 15 minutes. Exact assembly times will vary based on skill level and
past assembly experience.
6. Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote
control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result
the furnishing may tip over on to the child.
7. Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video
equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a child.
8. To prevent serious injury or death, this product is equipped with a wall anchoring system. Before this product
can be used, the wall anchoring system must be installed as directed in the assembly instructions.
Read all instructions before starting
Clear a flat covered space to begin
We recommend 2 adults for assembly
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number in the package
Helpful hints provided along the way
GENERAL BEST PRACTICES FOR ASSEMBLY
WARNINGS
MAINTENANCE
1. Clean periodically by wiping the product with a soft clean cloth.
2. Do not expose your product to any liquids. All liquids should be wiped up immediately with a soft, slightly
damp cloth in the direction of wood grain.
3. Do not expose your product to strong or direct sunlight, near heat outlets or air conditioning units, open
windows or dampness. Excessive exposure to sunlight and heat can cause fading of your furniture finish.
Extreme temperatures and humidity changes can cause wood cracking and splitting.
4. Clean using a glass/mirror cleaner and soft cloth. Do not use cleaning products containing abrasives,
as these will scratch glass/mirror.
!

TELEVISION
MAXIMUM FLAT PANEL: 54”
MAXIMUM LOAD: 60 POUNDS
BASE
MAXIMUM LOAD: 25 POUNDS
WARNING
!
MANUFACTURER: YOUNG CHAIN CO.,LTD
ITEM#: FP-P-1915-32
DISTRIBUTION: Big Lots Stores, Inc.
ADDRESS: P.O. BOX 28523, COLUMBUS,OH 43228-0523
COUNTRY OF ORIGIN: VIETNAM ;
MANUFACTURE DATE: 2022.05
SMALL SHELVES
MAXIMUM LOAD: 25 POUNDS
MIDDLE SHELF
MAXIMUM LOAD: 25 POUNDS
FOR USE WITH TELEVISIONS WEIGHTING 60 LBS (27.18 KG) OR LESS.
USE WITH HEAVIER TV MAY RESULT IN INSTABILITY CAUSING TIP OVER
RESULTING IN DEATH OR SERIOUS INJURY.
CAUTION
This Fireplace (FP-P-1915-32) is designed for flat panel LCD TVs weighing up to 60 lbs.
For items other than flat panel LCD TVs, this fireplace will support up to 135 lbs when the item is placed evenly
on the top surface. Use with other products may results in instability causing possible injury.
!

1PC
TOP
1PC1PC
BASEMIDDLE SHELF
1PC
LEFT PARTITION
1PC1PC
1PC
RIGHT PARTITIONRIGHT SIDE PANEL
LEFT SIDE PANEL
2PCS
SIDE TRIM
1PC 1PC 1PC
POST A POST B POST C
POST D
4PCS
SMALL SHELF
1PC
MIDDLE LEG
1PC
MIDDLE BACK PANELSIDE BACK PANEL
INSERT FIREPLACE
HEATER
2PCS
1PC2PCS
PART LIST
2PCS
DOOR

33pcs
CAM BOLT
33pcs
CAM LOCK
29pcs
WOOD DOWEL
2pcs
HANDLE
5pcs
BOLT
33pcs
ROUND HEAD SCREW
5pcs
ROUND HEAD SCREW
2pcs
DOOR BLOCK
17pcs
SHELF PIN
4pcs
DOOR HINGE
25pcs
SHORT FLAT HEAD
SCREW
5pcs
21pcs
STICKER
1pc
TOUCH-UP PEN
LONG FLAT HEAD
SCREW
HARDWARE LIST
1set
ANTI-TIPPING
NOT PROVIDED

HELPFUL HINTS
1. Screw the cam bolt into the predrilled panel. The cam bolt should be tightened
so no threads are visible.
2. The larger ring of the cam should touch the panel.
3. Insert the cam lock into the predrilled hole in the panel. Arrow faces the
outside of the panel.
4. Connect the previously tightened cam bolt with the panel connected into the
cam lock.
5. Using a flat head screw driver, turn the cam lock halfway clockwise to secure
the cam bolt.
6. FAILURE TO PROPERLY SECURE THE CAM LOCK AND CAM BOLT COULD RESULT
IN PRODUCT INSTABALITY AND FAILURE.
RING
SHOULD
TOUCH THE
BOARD
1 2 3
45 6

STEP 1
STEP 2
Place Post A (J), Post B (K), Post C (L) and Post D (M) on a soft smooth surface. The side with the most
holes should be facing up. Insert the Cam bolt (H1) into the corresponding hole of Post A (J), Post B (K),
Post C (L) and Post D (M) using the screwdriver (Not provided). Insert Wood dowels (H3) into the
remaining holes as shown in figure 1.
Not provided
Figure 1
12pcs 8pcs
4pcs
Not provided
Figure 2
Place Side trim (F) on a soft smooth surface with the holes facing up.Align the holes in Right Side panel
(E) with the holes of Side trim (F) and secure in place with Long flat head screw (H12) using the
screwdriver (Not provided) as shown in figure 2. Fully tighten all screws. Repeat this process to install
Side trim (F) to Left side panel (D).
Assembled View:
Assembled View:

STEP 3
STEP 4
Place Right side panel (E) on a soft smooth surface with the holes facing up. Insert the Cam Bolts (H1) and
Wood dowels (H3) of Post C (L) and Post D (M) into the corresponding holes of Right side panel (E) and
secure in place using Cam lock (H2) as shown in figure 3.
Note:The blocks of Right side panel (E) should be on the side of Post D (M) and the top ends should be flush.
Repeat this process to attach Post A (J) and Post B (K) to Left side panel (D) as shown in figure 3.
Note: The Blocks of Left side panel (D) should be on the side of Post A (J) and the top ends should be flush.
Insert Cam Bolt (H1) into Right side panel (E) and Left side panel (D) as shown in figure 3 and tighten using
screwdriver (Not provided) as shown in figure 3.
4pcs 12pcs
Figure 3 Not provided
Insert Cam bolt (H1) into the corresponding holes of Left & Right partition (G/H) using the screwdriver (Not
provided) as shown in figure 4.
Figure 4
4pcs
Assembled View:
Assembled View:

STEP 5
STEP 6
With assistance from another adult, hold Middle shelf (B) and Left partition (G) vertically as shown in
figure 5. Insert Wood dowels (H3) into the corresponding holes of Middle shelf (B) as shown in figure 5.
Slide the Cam bolts (H1) of Left partition (G) into the corresponding holes of Middle shelf (B) and secure
in place with Cam lock (H2) using screwdriver (Not provided).
Repeat this process to attach Right partition (H) to Middle shelf (B) as shown in figure 5.
Align the Door block (H8) with the pre-drilled pilot holes in the Left partition (G) and Right partition (H)
and attach with Round head screw (H7) using screwdriver (Not provided) as shown in figure 5.
Figure 5
4pcs
4pcs 2pcs
Not provided
Insert Cam bolt (H1) into the corresponding holes of Base (C) using the screwdriver (Not provided).
Insert Wood dowels (H3) into the corresponding holes of Base (C) as shown in figure 6.
Figure 6
4pcs
Not provided
Assembled View:
Assembled View:
8pcs
4pcs

STEP 7
STEP 8
With assistance from another adult, place Left side panel (D) on edge as shown in figure 7.
Align the holes in Left partition (G) and Right partition (H) with the Cam bolts (H1) in Base (C) and slide
into place as shown in figure 7. Secure the Left partition (G) and Right partition (H) to Base (C) with Cam
lock (H2) using screwdriver (Not provided).
Align the Cam bolts (H1) in Left side panel (D) with the corresponding holes in Base (C) and slide into
place. Secure the Left side panel (D) to Base (C) with Cam Lock (H2) using screwdriver (Not provided).
Repeat this process for the Right side panel (E) as shown in figure 7.
8pcs
Figure 7
Not provided
Insert Wood dowel (H3) into the indicated holes of the Left side panel (D), Left partition (G), Right
partition (H) and Right side panel (E) as shown in the figure 8.
Insert Middle leg (Q) into Base (C) and turn clockwise until tight as shown in figure 8.
8pcs
Figure 8
Assembled View:
Assembled View: