real living OAKMONT GBO19-002 User manual

OAKMONT 3PC ALL WEATHER WICKER GLIDER SET
Need help? We are here for you! 1-888-733-8169 24/7 Toll Free
Or email us at [email protected], [email protected]
[email protected]
ASSEMBLY INSTRUCTION
ITEM# : GBO19-002 / GBO19-002NAVY
SKU# 810410477 / 810461020

STAIN RESISTANT CUSHIONS CARE —— KEEP THE CUSHIONS IN STORAGE IN RAINING DAY.
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone. Allow cushions to air dry.
FABRIC CARE: Hand wash cold, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.
ALL WEATHER WICKER PRODUCT CARE
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild
solution of soap and water, rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Over time nuts and
screws can loosen. Occasinally, check nuts and screws on all chairs and table, re-tighten if necessary.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use.
The chairs and table are not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
The chair is used at weight of 250lb (113.4kg). Improper use of this product or failure to use as directed may
result in injury. Not intended for commercial use.
MAINTENANCE
WARNINGS:
Use the correct screws as indicated. All screws should be hand tight untill the complete piece is assembled (
This will make the assembly process much easier ). Once the piece is fully assembled, then go back and tight
all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the product
construction.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical
wires.
Pay attention to orientation
Letter of the part corresponds to a stcker on the products
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
GENERAL BEST PRACTICES FOR ASSEMBLY:
Read all instructions before starting
Clear a flat covered space to being
Always best to do it with a friend
Note that hardware required is provided for every step

A1 A2 B C
1PC Left Arm 1PC Right Arm 1PC Chair Back 1PC Seat Panel
D E M N
1PC U-shaped Fitting 1PC Chair Base 1PC Seat Cushion 1PC Back Cushion
F G H I
4PC Spring Washer 18PC Washer 8PC Nut 4PC Screw(φ6x15mm)
J K L
14PC Screw(φ6x35mm) 1PC Allen Wrench 1PC Open End Wrench
PARTS LIST
HARDWARE LIST
STEP 1
Secure chair back (B) to left arm (A1) with 2 screws (I) and 2
washers (G) by using allen wrench (K). Do not tighten all screws
now.

Secure seat panel (C) to assembled chair back (B) with 2 screws (J)
and 2 washers (G) by using allen wrench (K), verify the alignment
and adjust, fully tighten all the screws now.
STEP 3
Secure seat panel (C) to assembled left arm and right arm (A1.A2)
with 4 screws (J) and 4 washers (G) by using allen wrench (K). Do
not fully tighen now.
STEP 4
STEP 2
Secure right arm (A2) to assembled chair back (B) with 2 screws (I)
and 2 washers (G) by using allen wrench (K). Do not tighten all
screws now.

STEP 6
Push the top plate on the base (E) with different position to make the
holes open for ready assembling. Connect the 4 screws (J) through
the holes of the plate on the base (E) and the holes on the tube of U-
shaped fitting (D) with 8 washers (G) , 4 spring washers (F) and 4
Nuts (H) by using allen wrench (K) and open end wrench (L) .
NOTE: THIS STEP IS VERY IMPORTANT. DO READ THE
INSTRUCTION AND DIAGRAM CAREFULLY.
STEP 5
Turn over the assembled chair bucket and secure the swing arms on
U-shaped fitting (D) to the bottom tube of left arm (A1) and right arm
(A2) with 4 screws (J), and 4 nuts (H) with allen wrench (K) and
wrench (L).
NOTE: PLEASE FIX TWO SCREWS IN DIAGONAL POSITION TO
KEEP THE BALANCE THEN FIX THE OTHER TWO SCREWS.