real living LAKEWOOD GBO23-914ST User manual

LAKEWOOD ALL WEATHER WICKER UMBRELLA SIDE TABLE
ASSEMBLY INSTRUCTIONS
ITEM# : GBO23-914ST
SKU# : 810580417
Need help? We are here for you! 1-888-733-8169 Toll Free
Or email us at cus[email protected],[email protected]
[email protected]

GENERAL BEST PRACTICES FOR ASSEMBLY:
Read all instructions before starting
Clear a flat covered space to begin assembly
Always best to do it with a friend
Note that hardware required is provided for every step
Pay attention to orientation
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
WARNINGS:
To avoid hazards caused to the product or people around it, make sure to have weights applied to the base
of the table before you use umbrella with the table.
Use the correct screws as indicated. All screws should be hand tightened until the complete piece is
assembled ( This will make the assembly process much easier ). Once the piece is fully assembled, then go
back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the
product construction.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or
electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use.
The table is not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
Improper use of this product or failure to use as directed may result in injury. Not intended for commercial
use.
MAINTENANCE
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone.
ALL WEATHER WICKER PRODUCT CARE
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a
mild solution of soap and water, rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Screws can
loosen over a period of usage, please check the screws occasionally and re-tighten if necessary.

PARTS LIST
A
B
C
1PC Table Top 2PC Leg Panel 2PC Side Panel
D
E
1PC Steel Hoop Plate 1PC Umbrella Pole
HARDWARE LIST
F
G
H
16PC Washer 8PC Screw(φ6x16mm) 8PC Screw(φ6x30mm)
J
K
1PC Allen Wrench 2PC Regulating Screw(φ6x20mm)

STEP 1
Secure 1 steel hoop plate (D) to 2 leg panel (B) by
using 2 screws (G) and 2 washers (F) with allen
wrench (J). Do not fully tighten all screws now.
STEP 2
Secure 2 side panels (C) to steel hoop plate (D) by
using 2 screws (G) and 2 washers (F) with allen
wrench (J). Do not fully tighten all screws now.
B
D
F
G
J
F
D
C
C
G
J
F
G
J
F

STEP 3
Secure 2 leg panel (B) to 2 side panels (C) by using
8 screws (H) and 8 washers (F) with allen wrench (J).
Do not fully tighten all screws now.
STEP 4
Secure 1 umbrella pole (E) to 1 steel hoop plate (D)
by using 4 screws (G) and 4 washers (F) with allen
wrench (J) to fully tightened.
B
C
E
D
J
H
F
J
G
F

STEP 5
Turn over the assembled table frame, place the table
top (A) on it. Secure table top (A) to 2 leg panels (B)
by using 2 regulating screws (K).
STEP 6
Verify the alignment and adjustment, fully tighten all
screws.
Warranty
One year limited warranty.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer's responsibility for freight and packing charges to and from the service center.
LOAD THE WEIGHT ( SANDS BAG, STONE AND ETC. )
ONTO THE STEEL HOOP PLATE
A
B
K