real living BQ092-1320 User manual

Page 2 of 6
Read all instructions before starting
Clear a flat covered space to being
Two people are recommended for assembly.
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number in the package
Helpful hints provided along the way
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Regularly check hardware and tighten if necessary.
Use dry cloth to wipe up dirt and spills as necessary.
Keeping Away from water and fire.
DO NOT USE POWER TOOL.
SUGGEST 2 ADULTS TO ASSEMBLE THIS PRODUCT IN AN OPEN AREA.
DO NOT USE POWER TOOLS TO ASSEMBLE

Page 3 of 6
NO QTY DESCRIPTION
A 1pc
B1pc
C1pc
D2pcs
0
E1pc
F 1pc
G 2pcs
Wooden Dowel
32pcs
PARTS LIST
Cam Lock
Cam Bolt
NO QTYPARTS DESCRIPTION
1 18pcs
218pcs
HARDWARE LIST
Top Panel
Divider
Shelf Panel
Top Metal Frame
Right Metal Leg
Short Metal Bar
Screw
4
5
2pcs
12pcs Bolt(6×10mm)
A
G
H
G
H
BC
D
D
EF
H2pcs Long Metal Bar
Left Metal Leg

Page 4 of 6
HOW TO INSTALL THE CAM BOLT AND CAM LOCK
a b c
NO QTYPARTS DESCRIPTION
HARDWARE LIST
HELPFUL HINTS
61pc Nut(6×15mm)
A
A
A
C
2x2
3x2
2
1x2
1
4x2
B
B
1
1
2
2
33
4
4
81pc Nut(6×5mm)
91pc Allen Wrench
74pcs Nut(6×20mm)
1. Insert Cam Bolt (1) into Top Panel (A) and fully
tighten using Phillips screwdriver (not provided).
2. Align the Cam Bolt (1) in Top Panel (A) with the
holes in the edge of Divider (B) and slide into place.
3. Secure the panels together with Cam Lock (2)
using Flat Head screwdriver (not provided)
1. Insert Wooden Dowel (3) into the edge of
Divider (B) as shown in the diagram.
2. Align the holes in Shelf Panel (C) with the
Wooden Dowels (3) in Divider (B) and slide
into place.
3. Secure the panels together with Screw (4)
using Phillips screwdriver (not provided).
Fully tighten screws.
• A Phillips Screwdriver and a flat head screwdriver will be needed for assembly and are not provided.
• Separate parts before starting.

Page 5 of 6
7
7
77
7
9
5
7x
4
2x
16
4
1x16
3
D
D
D
D
E
F
1111
11111111
1111
D
A
C
2222
2
2
2
2
D
D
AC
2222
2222
9x
1
180°
Insert Cam Bolt (1) into Top Metal Frame (D) and fully tighten using Phillips
screwdriver (not provided).
1. Align the Cam Bolt (1) in Top Metal Frame (D) with the holes in the edge
of Top Panel (A) and Shelf Panel (C) and slide into place.
2. Secure the Top Metal Frame (D) and panels together with Cam Lock (2)
using Flat Head screwdriver (not provided).
C
1. Carefully place the Assembled Parts in Step 4 so
the bottom side is facing up as shown in the diagram.
2. Insert the posts of Top Metal Frame (D) into Left
Metal Leg (E) and Right Metal Leg (F) as shown in the
diagram.
TIP: The bolt holes on the sides of Metal Legs (E and F)
should be on the same side. The holes in Shelf Panel (C)
and Metal Legs (E and F) should be aligned.
3. Secure Metal Legs (E and F) to Shelf Panel (C) with
Bolt (7) using Allen Wrench (9). Fully tighten bolts.
3. Carefully turn the assembled pieces over onto Top Metal Frame (D).
Follow instructions 1 and 2 to assemble remaining Top Metal Frame (D)
to the assembled pieces.

8
6
8
5x4
Page 6 of 6
76x
1
5x8
6
F
E
G
G
G
G
H
H
H
H
8x
1
9x1
9x
1
9x1
6
5
5
5
5
5
8
GG
H
H
5
5
5
5
E
F
Attach Left Metal Leg (E) and Right Metal Leg (F) to Top Metal Frame (D)
with Bolt (5) using Allen Wrench (9). Fully tighten bolts.
1. Insert the Bolt (6) into the holes on one end of every Short Metal Bars (G)
and Long Metal Bars (H) as shown in the diagram.
2. Place the Nut (8) onto the Bolt (6) and fully tighten using Allen Wrench (9).
NOTE: The flat side of Short Metal Bars (G) and Long Metal Bars (H) should
face the Nut (8).
Attach the Assembled Short Metal Bars (G) and Long Metal Bars (H) as
shown in diagram to Left Metal Leg (E) and Right Metal Leg (F) with
Blot (5) using Allen Wrench (9). Fully tighten Bolts.
NOTE: The flat side of Short Metal Bars (G) and Long Metal Bars (H)
should face the Left Metal Leg (E) and Right Metal Leg (F).
Assembly is now complete.