real living RIDGEWOOD TCS40CB User manual

TM
RIDGEWOOD
40 INCH SQUARE TILE TOP TABLE
ASSEMBLY INSTRUCTION
ITEM#: TCS40CB
SKU# 810452009
Need help? We are here for you! 1(877)539 – 7436 •Toll Free
[email protected] • Email Address

PAGE 1 OF 4
Table is not to be used as a seating surface. Improper use of this product or failure to use may result in injury.
Read all instructions before starting
Clear a at covered space to begin assembly
Always best to do it with a friend
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Retain these assembly instructions for future reference.
Regularly check hardware and tighten if necessary
Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or
other solvents on the frame parts.
Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your table.
When moving the table, remove the umbrella and lift. Do not drag this table.
We recommend the use of furniture covers when not in use.
In order to prolong the life and beauty of your table, we recommend that it be stored in a dry and protected area
during o season periods.
The umbrella should be lowered and/or removed in windy conditions.
Use the correct bolts as indicated. Do not tighten any of the bolts until the table is completely assembled.
Do not sit or stand on this table.
A weighted umbrella base must be used when using an umbrella with this table.
Do not discard of any of the packaging until you have checked that you have all of the parts and ttings required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.

PAGE 2 OF 4E-320
PARTS LIST
STEP 1
PARTS REQUIRED: 1, 2, 9, & 10
Keep the bolts loose.
x4 x4
9 10
TCS40CB-CS05-1
TCS40CB-CS04-1
TABLE TOP
LEG
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1 1
1
1
42
3
4
CENTER
CONNECTOR WITH RING
PLASTIC CENTER PLUG
PROTECTOR RING
TCS40CB-CS06-1
18000144002
1
18110105002
5
13C??1B3000A001
TILE B 600*148.5*10
TILE C 149.5*149.5*10
8
10
4
4
13C??2CF100A001
TILE A 600*600*10
12
17FA05040301-YX
1
13C??1B0200A201
WASHER d6.5*D13*1.0
917C33A0706001YX 12
BOLT M6*15
7
6
500 10 20 30 40 60 70 80 90
mm 100
Ⅴ
Tools
2
2
2
2
9
10
1

x1 x4
6 7
x4
8
PAGE 3 OF 4E-320
STEP 3
PARTS REQUIRED: 1, 6, 7, & 8
STEP 2
PARTS REQUIRED: 2, 3, 9, & 10
Tighten all bolts by using the supplied Hex key.
x8 x8
9 10
2
22
99
10
10
2
3
A
Note:
If any EVA foam pads on the table top are missing,
there are extra EVA foam pads in the hardware kit.
See Illustration A.
6
8
7
1

PAGE 4 OF 4E-320
PARTS REQUIRED: 1, 4, & 5
Warranty
•One–year limited warranty.
•Proof of purchase (dated register receipt) is required for warranty claims.
•It remains the customer’s responsibility for freight and packing charges to and from the service center.
x1 x1
4 5
Note:
To use an umbrella with this table, remove the plastic
center plug and put the umbrella pole through the
table top and center connector ring.
STEP 4
1
4
5