real living KYW-11390B User manual

TM
4PC KIDS SURFBOARD TABLE & STOOL SET
ASSEMBLY INSTRUCTIONS
ITEM#: KYW-11390B
SKU#: 810587397
Need hel
1-800-935-3959 Toll Free or email us at [email protected]
p? We are here for you!

Read all instructions before starting
Clear a flat covered space to begin
Always best to do it with a friend
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
Use the correct screws as indicated. All screws should be hand tightened until the complete piece is assembled ( This will make
the assembly process much easier ). Once the piece is fully assembled, then go back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the
product construction. Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging
branches, laundry line or electrical wires. Some parts may contain sharp edges.
When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury
and damage to the product. Please read all instructions before assembly and use.
The stool and table are not to be used for standing purposes. Use on even surfaces only.
The stool is used at weight of 110lbs (50kgs) and table is used at weight of 66lbs (30kgs). Improper use of this product or failure
to use as directed may result in injury. Not intended for commercial use.
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Fabric care:
Hand wash cold, Lay flat to dry, Cool iron if necessary. Do not dry clean
Wood care:
Before using, clean the product completely with a soft dry towel. Screws will be loosened over a period of usage, please check
the screws occasionally and re-tighten if necessary.

PARTS LIST
HARDWARE LIST
x2
Seat
x2
Support rail
AB
x4
Leg
C
x12
Phillips screw
x4
Wood bolt
x12
Barrel Nut
3
25
1.57”
8*40mm
2.75”
M6*70mm
M6

Important: Press a barrel nut(5) into
the hole in the part, making sure
the “-“ pattern is facing up.
Important: Using a standard screw
driver, turn the nut until the “-“ is
straight and the treaded hole is
facing outwards to accept the screw.
!
!
HELPFUL HINTS
· Tools needed, but not included:
· Separating parts before starting
How to install barrel nuts
5

STEP 1
x4 x12
2
2
2
2
3
3
3
3
Assembled View: Stool
M6*70mm M6
8*40mm
x12
5
5
5
C
B
B
A
x 2
x2
x4
C
3
3
3
Put 12 x part (5) into the hole of seat (A)
and support rail (B), Make sure the "-" of
barrel nut is alighed up the hole. Attaching
leg to seat and wood support rail with 12
x part (3) and 4 x part (2)
2pcs

PART LIST
HARDWARE LIST
x2
Short cross bar
x2
Left leg
x1
Table top
x1
Long cross bar
x2
Right leg
E
D
H
G
F
x1
Canopy with upper post of umbrella
x1
Bottom post of umbrella
J
I
x4
Phillips screw
x6
Wood bolt
x10
Machine screw
x6
Barrel Nut
x8
Hexagon Nut
3
2
1
5
x1
Wrench
6
4
M6*55mm
2.16”1.57”
8*40mm
2.75”
M6*70mm
M6 M6

STEP 2
x4 x4
23
Assembled View:
M6*70mm M6
8*40mm
x4
5
2pcs
3
3
2
2
E
D
F
5
5
Put 4 x part (5) into the hole of
wood cross bar of table leg (E), Make
sure the "-" is aligned up of hole. Attaching
right & left leg (D & F)to cross bar (E) with
4 x part (3) and 4 x part (2)
x 2

STEP 3
x2 x2
1
1
1
G
2
Assembled View:
M6
8*40mm
x2
5
M6*55mm
2
2
5
5
Put 2 x part (5) into the hole of long cross
bar of table leg (G), Make sure the "-" is
aligned up of hole. Attaching assembled
right leg and left leg to long cross bar (G)
with 2 x part (1) and 2 x part (2)

STEP 4
Attaching legs to table top (H) with 8 x
part (1) and 8 x part (4) and wrench (6)
x8 x8
14
Assembled View: Table
M6*55mm
x4
M6
4
1
1
H
x1
6
6

STEP 5
Screwing on the bottom post of umbrella (I)
and canopy with upper post of umbrella
(J) in clockwise orientation
Assembled View:
J
I

STEP 6
Made in China