real living BL-VY-B-SM-3A User manual

GENERAL BEST PRACTICES FOR ASSEMBLY:
Read all instructions before starting
Note that hardware required is provided for every step
Pay attention to orientation
Serious injury or death may result if this product topples over. To prevent serious injury or death, this product is equipped with a
wall anchoring system.
DO NOT place heavy items such as TVs on this product. This could lead to tip over causing serious injury or death.
Stop using the product if any parts are missing or damaged.
Children should only use this product with adult supervision. DO NOT allow children to climb or play on this product as it may
cause tipover resulting in serious injury or death.
injury or death.
Check bolts/screws periodically and tighten if necessary.
Carefully wipe with soft cloth.
Clear a fat covered space to being
GENERAL BEST PRACTICES FOR ASSEMBLY:
WARNINGS:
MAINTENANCE:
A philips head screwdriver is necessary for assembly but is not included.
Care should be taken when using sharp objects around this product as they may damage the product surface.
Before this product can be used, the wall anchoring system must be installed as directed in the assembly instructions.
During assembly, keep all small parts out of the reach of children. Small parts present a choking hazard and may cause serious
Helpful hints provided along the way
Number of the hardware corresponds to its number in the package
Letter of the part corresponds to a sticker on the product
You will need two adults to assemble this item
.
babies

PARTS LIST
A
X1
B
Table Legs Drawer Front
BC
DE
Drawer Right Side
N
Drawer Bottom
FGH
I
Drawer Left Side Drawer Back
Mirror Frame
Top Panel
41
X1 X1 X1
X1 X1 X1
Stool Cushion
Stool Legs
4

HARDWARE LIST
X16
Allen Bolt
X3X16
Spring Washer
X19 X1
Knob
X1
Bolt
X1
Flat Washer
X3
Anti-tipping Kit
HH510
Allen Bolt
X
123
7
10
89
Flat Washer
X1 Bag
Ø1/4 x 2" Ø1/4 x 1-1/2" Ø1/4" x Ø19
#8 x 25mm
4 x 60mm
Allen Key Screw
Ø1/4" x Ø1
Ø1/4" x Ø11 Ø30" x Ø30 x 32mm Ø5/32 x 30mm
4 5 6

HELPFUL HINTS
!
Check all bolts
that are loose.
CARE AND CLEANING
and fully tighten any
Treat uphostered surfaces with care. Clean any spills immediately using
a clean, slightly dampened cloth and dabbing the area until the spill is
time. Periodically check all bolts and fully tighten any that are loose.
removed. DO Not use any chemical cleaners. Hardware may loosen over

STEP 1
B
B
B
B
A
1
x8
X8
X8
3
4
7
3
7
1
4
X1
Assembled View:
Ensure the legs are straight and fully tighten the bolts.
Washer (4) and Flat Washer (3) using Allen Key (7).
smooth surface to avoid scratching the surface. Attach
Table Legs (B) to Top Panel (A) with Allen Bolt (1), Spring
Carefully place the Top Panel (A) upside down on a soft

STEP 2
E
E
E
D
D
D
F
F
C
N
8
X8
8
8
Assembled View:
8
8
C
C
Page 6 of 12
Insert the Drawer Bottom (F) into the groove of Drawer
Attach the Drawer Right Side (D) and Drawer Left Side (E)
screwdriver (not included). Fully tighten screws.
and Drawer Left Side (E) with Screw (8) using Phillips
Attach the Drawer Back (N) to Drawer Right Side (D)
to the Drawer Front (C) with Screw (8) using Phillips
Right Side (D) and Drawer Left Side (E) until fully inserted
into the groove of Drawer Front (C) .
screwdriver (not included). Fully tighten all screws.
Screwdriver
(Not included)

Assembled View:
5
6
6
X
X
6
Screwdriver
(Not included)
STEP 3
Page 7 of 12
Attach the Knob (5) to Drawer Front (C) with Bolt (6)
using Phillips screwdriver (not included) and fully tighten.

Assembled View:
STEP 4
Insert the assembled drawer into the table.
With assistance from the other adult, return
the assembled table to the upright position.

4
7
X1
2
9
Assembled View:
9
4
2
7
x3
X3
X3
STEP 5
Allen Key (7). Fully tighten all bolts.
Attach the Assembled irror (G) to the Table Top with Allen
Bolt (2) Spring Washer (4) and Flat asher (9) using
Page 9 of 12

I
I
I
1
x8
X 8
X8
3
4
7
X1
Assembled View:
1
4
7
3
STEP 6
Page 10 of 12
Place the Stool Cushion (H) upside down. Attach Stool
Ensure Legs are straight and fully tighten all bolts.
Legs (I) to Stool Cushion (H) with Allen Bolt (1), Spring
Washer (4) and Flat Washer (3) using Allen Key (7).

10
1
X1 Bag
HH510
Screwdriver
(Not included)
STEP 7
H7
Page 11 of 12
wall and prevent tip over.
at the marked location.
wall using the plastic strap.
Install one bracket in the top center of the table back using
one of the provided screws.
Remove the table and attach the remaining bracket to wall
Attach the bracket on the vanity to the bracket on the
the installed bracket meet the wall.
Install the Anti-tipping Kit (10) to secure the vanity to the
Place the vanity in the desired location and mark where

STEP 8
Page 12 of 12