real living 52201-CRM User manual

MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
CARE AND CLEANING
1

E
PARTS LIST
A
x1
Back Cushion
B
x1
Seat Cushion
x1
Seat Plate
F
D
x1
FE +
Gas Lift
x1
Base and Base Cover Metal Legs
G
x5
C
2
H
x5
Casters

1
x10
Screws
M6 x 15mm
2
x8
Screws
M8 x 25mm
3
x1
Allen Key
HARDWARE LIST
3

HELPFUL HINTS
4
Before assembly, please remove all parts from the carton, verifying that
you have the correct quantities, and read all the instructions.
Important:
This chair is only meant to seat one person at a time.
Do not use chair as a step stool/ladder.
Failure to follow these warnings may result in injury.
Do not stand on the seat cushion.
Do not allow children to play on or near this product.
For indoor use only. Please do not expose to direct sunlight, sources
of excessive heat, or use in wet or damp environments.
Only a damp cloth should be used to clean the upholstery surface. For
persistent stains and overall cleaning, contact a professional upholstery
cleaning company.
The casters sold with this chair are intended for use on carpet and not
recommended for use on tile or hard wood floors. Using these casters on
tile or wood flooring may cause floor surface damage, so please consider
purchasing a chairmat to protect your floor surfaces.
Do not use power tools. Only use the Allen Key provided. Check and
re-tighten screws and knobs every 90 days.
1
2
3
4
5
6
7
8
9

STEP 1
Take off Base Cover (F) from the Base (E), then turn the base over.
Insert Metal Legs (G) into the Base (E) and secure by 10 Screws (1).
Tighten all the screws.
Warning: Fully hand-tighten all 10 screws at each leg/hub connection.
Be careful not to overtighten or strip bolts. Do not use power tools. If
you experience a problem with the leg attachment or are unable to fully
tighten any of the bolts, stop. Do not use the base. Contact Customer
Service for assistance. All bolts should be checked and re-tightened
every 90 days.
G
E
G
E
1
3
5
1
x 10
E
FF
E

STEP 2
STEP 3
Press the Casters (H) into holes at the end of
each leg. Turn the base upright and then
attach the Base Cover (F) to the Base (E) as
shown. Insert Gas Lift (D) into the center hole
of base.
2Align the Back Cushion (A) with the Seat
Cushion (B) and attach the back support
plates onto the bottom of the Seat Cushion
(B) by using 4 Screws (2). Tighten all the
screws.
x 4
6
HD
F
E
2
B
A
2
3

STEP 4
7
D
C
STEP 5
2
x 4
B
C
2
3
Align Seat Plate (C) over pre-drilled holes on
the underside of the Seat Cushion (B) with
front of seat plate facing the front of the seat
cushion. Attach the Seat Plate (C) to Seat
Cushion (B) using 4 Screws (2) as shown.
Tighten all the screws with the enclosed Allen
Key (3).
Turn assembled seat upright and locate
central hole of Seat Plate (C) over Gas Lift (D).
Push down firmly until connection is secure.

8
The Chair is completed now.
STEP 6

FUNCTION INSTRUCTION
TO ADJUST SEAT HEIGHT
While seated, lean forward, lifting your body weight
from the seat. Reach underneath the right side of
chair and locate the handle. Lift the handle up slowly
to allow the chair to rise to the desired height. To
lower seat height, lift the handle slowly while seated.
TO TURN OR ROTATE CHAIR
360˚ swivel.
9
PRINT IN VIETNAM