RealFlame C820LP User manual

C820LP Brenner Fire table NG Conversion Kit
Improper installation, adjustment,
alteration, service or maintenance
can cause property damage
personal injury, or loss of life.
Read the installation, operation
and maintenance instructions
thoroughly before installing or
servicing this equipment.
!!
IMPORTANT WARNING
SAVE THESE INSTRUCTIONS
!DANGER
If you smell gas:
gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance and
immediately call your gas supplier or fire department.
USC
For Technical Support Please Contact Real Flame® At: 1-800-654-1704

PARTS LIST 00023101E
1
2
3
NATURAL GAS CONVERSION KIT
NOTE
This conversion kit is for changing a Liquefied Petroleum (LP) fire bowl into a Natural Gas
fire bowl.
!
WARNING
!
Natural Gas Hose and Quick Disconnect
NG Orifice Spud 4.18mm
3
Conversion Plaque
1
• If the information in these instructions is not followed exactly, a fire, explosion or
production of carbon monoxide may result causing property damage, personal injury
or loss of life.
• The qualified service agency is responsible for the proper installation of this kit. The
installation is not proper and complete until the operations of the converted appliance
is checked as specified in the manufacturer’s instructions supplied with this kit.
• This conversion kit shall be installed by a qualified service agency in accordance with
Real Flame’s instructions and all applicable codes and requirements of the authority
having jurisdiction.
1
2
C820
4.18mm

NATURAL GAS CONVERSION
2
1.) Flip table upside down. Place on a soft surface to avoid damaging
the finish.
2.) Remove nuts from component
box and set box aside.

NATURAL GAS CONVERSION
3
3.) Disconnect LP hose from valve.
4.) Disconnect bellows (Corrugated Stainless Steel Tube/CSST) from
burner base.
Bellows

4
NATURAL GAS CONVERSION
5.) Remove the existing LP orifice spud.
LP Orifice Spud

5
NATURAL GAS CONVERSION
6.) Locate the new NG orifice spud, verify it is the correct number.
The sign 4.18mm is painted with a black mark.
7.) Screw the new NG orifice spud into the burner base.
4.18
NG Orifice Spud

6
NATURAL GAS CONVERSION
8.) Re-attach bellows (CSST) to new spud.
9.) Attach NG hose to the input side of the valve.
Bellows

7
NATURAL GAS CONVERSION
NOTE: The normal manifold pressure for this converted appliance is 7” water column.
NOTE: The maximum inlet gas pressure for this unit is 10.5 in W.C. (2.61 kPa).
The minimum inlet gas pressure for this unit is 3.5 in W.C. (0.87 kPa).
Check for leaks at these locations
11. CHECKING FOR LEAKS
Make a leak check solution by mixing 1 part dishwashing soap
with 3 parts water in a spray bottle.
Make sure the re bowl control knob is “OFF.” Then, turn the
natural gas on at its source.
Spray leak solution on the valve connections, paying particular
attention to the areas indicated by the arrows.
If any bubbles appear turn the natural gas o at its source,
reconnect and re-test. If you continue to see bubbles after several
attempts, disconnect the natural gas source and contact Real
Flame® at 1-800-654-1704 for assistance.
If no bubbles appear after one minute, turn the gas
source “OFF”, wipe away solution and proceed to next
step.
10.) Attach quick disconnect to gas supply.
House Natural Gas Piping
Shut-o Valve
Quick Disconnect Socket
NG Gas Hose
To Fire Bowl

12.) After installing the conversion kit, verify the location of the
Thermocouple and Igniter Pin using the illustration below.
Installing at Altitude
For installations at elevations above 2000 ft. contact your local dealer or gas
supplier before installing as input rating should be reduced approximately 4%
for each 1000 ft. above sea level. Refer to the National Fuel Gas Code.
Contact the Real Flame for more information at 1-800-654-1704
13.) Note to installation technicians. Verify the manifold pressure by using a
3/8” flared T-junction at the location marked by the arrow below. Then using
a digital manometer verify that the pressure before the orifice is 7” W.C. Also
verify that the orifice spud has the 4.18 marked. This will allow you to verify
that the input rating of the appliance is correct.
NATURAL GAS CONVERSION
8
Igniter Pin
NOTE: Pilot housing removed for example only.
Thermocouple .25”
.15” .15”
To Manometer

15.) Remove the cable kit, re-attach French plaque, info plaque and NG conversion
plaque to the fire table, then connect cable.
Remove Cable Re-attach both plaques
NATURAL GAS CONVERSION
WARNING
!
9
Before using this outdoor fire table, make sure you have read, understand and are following all
information provided in the Important Safety Information section of this manual. Failure to
follow those instructions can cause property damage, serious injury or death.
14.) Connect component box with nuts.
French
French
NG
Conv.