Reebok REV-10101 User manual

User Manual
Elliptical Trainer REV-10101

2
SAFETY PRECAUTIONS
Before beginning any exercise program, you should consult with your doctor. It is recommended
that you under go a complete physical examination.
Work within your recommended exercise level, do not work to exhaustion. If you feel any pain
or abnormal pains, stop your workout immediately. Consult your physician immediately.
Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
For safety, the equipment should have at least 0.5 meter off free space all around it.
Do not allow children to play on or around your Cross trainer. Keep hands away from moving
parts.
Check your cross trainer prior to exercising to ensure that all parts are assembled, and nuts,
bolts, pedals and the saddle are tightened before every use.
Always check to see that seat is securely fastened before using your cross trainer.
Always wear proper workout clothing and shoes when using your cross trainer. Do not wear
loose clothing. Do not wear shoes with high heels.
The equipment compliant to EN957 under class H.C. Suitable for domestic, home use only.
Maximum weight of user is to be 100kg. Breaking is speed independent.
IMPORTANT
Please read instructions carefully before assembling.
Please remove all the parts from the carton and identify them against the parts list to ensure you
have all the parts . If you are missing any parts please call our Technical Support Line:
0871 474 2614
Do not destroy the carton until you have assembled the cross trainer completely.
Always use the equipment as indicated. If you find any defective components whilst assembling
or checking the equipment, or if you hear any unusual noise coming from the equipment during
use, stop. Do not use the equipment until the problem has been rectified. Call the Technical
Support line on 0871 474 2614

HARDWARE PACKING LIST
K
ey# Description Quantity
13.CARRIAGEBOLTM10*75 4
3
14.DOMEDNUTM10 4
15. ARC WASHER Φ10.5*Φ25*T1.5 4
16. ROUND HEAD BOLT M8*15 4
17. ARC WASHER Φ8.5*Φ22*T1.5 4
18. HEX HEAD BOLT M10*80 2
19. FLAT WASHER φ10.5xφ20xT1.5 4
20.NYLONLOCKNUTM10 2
21. SLEEVE TUBE 2
24.ROUNDHEADBOLTM6*15 4
25. CARRIAGE BOLT M6*φ8*25 4
26. SCREW φ5*15 12
74L..PVCCAP (L) 2
74R.PVCCAP ® 2
ALLENWRENCH(HexKey)L6 1
HEXWRENCHL13~17 1
ALLENWRENCH(HexKey)L4 1

Explode Drawing
R
L
R
L
4

5
Part List
No. PART NAME Q'TY No. PART NAME Q'TY
1 Main frame 1 41 Clip 2
2 Front stabilizer 1 42 Belt Drive Wheel 1
3 Rear Stabilizer 1 43 Flywheel 1
4 Front Post 1 44 Nylon Lock Nut M6 2
5 Left Lower Hand Rail 1 45 Adjust Screw Washer 2
6 Right Lower Hand Rail 1 46 Flat Washerφ10.5xφ25xT1.5 2
7 Left Foot Rail 1 47 Belt Adjust Screw M6x40 2
8 Right Foot Rail 1 48 Cross Crank 2
9 Left Upper Handle Bar 1 49 Screw φ4x15 8
10 Right Upper Handle Bar 1 50 Screw M6x20 4
11 Front Handle Bar 1 51 Disk 2
12 Computer 1 52 Flange Screw M8x20 2
13 Carriage Bolt M10 x 75L 4 53 Disk Cap 2
14 Domed Nut M10 4 54 Small Sleeve 4
15 Arc Washerφ10.5xφ25xT1.5 4 55 Big Sleeve 4
16 Round Head Bolt M8 x 15 4 56 Flat Stopper 2
17 Arc Washer φ8.5xφ22xT1.2 4 57 Flat Washer φ38xφ19xT2 2
17A Split Washer M8 4 58 Hex Bolt M8x25 2
18 Hex Head Bolt M10*80 2 59 Domed Nut M8 2
19 Flat Washer φ10.5xφ20xT1.5 4 60 Spacer 2
19A Flat Washer φ10.5xφ25xT1.5 2 61 Hand Pulse Sensor 2
20 Nylon Lock Nut M10 4 62 Screw M4x15 2
21 Sleeve Tube 2 63 Font Hand Grip 1
22 Domed Nut M10 2 64 Upper Hand Grip 2
23 Flat Washer φ19xφ31.8xT1.5 2 65 End Cover 2
24 Round Head Bolt M6x15 4 66 Main Cover Left 1
25 Carriage Bolt M6*φ8*25 4 67 Main Cover Right 1
26 Screw Φ5x15 12 68 Front Post Cover Left 1
27 Front End Cap with Wheel 2 69 Front Post Cover Right 1
28 Rear End Cap 2 70 Rear Cover 1
29 Middle Computer Wire 1 71 Screw φ5x15 22
30 Lower Computer Wire 1 72 U Type Nut 2
31 Hand Pulse Middle Wire 1 73 End Cap for Foot Tube 2
32 Hand Pulse Lower Wire 1 74L PVC Cap(L) 2
33 Computer Upper Wire 1 74R PVC Cap ® 2
34 Hand Pulse Upper Wire 1 75 Small Motor 2000 type 1
35 Adapter 6V 1 76 Magnet Control Cable 1
36 Foot Pad 2 77 Foot Pad Support 2

37 Adjust Knob for Foot Pad 4 78 Screw M6x25 4
38 Flat Washerφ8.5xφ22xT2 4 79 Transmission Belt 1
39 Screw M5x10 4 80 Bottle Holder 1
40 Bearing 6004Z 2
Assembly Drawing
6
R
26
L
26
26
L
26
R

Assembly
# STEP 1.
A) Attach the rear foot tube (3) to the main frame (1) fasten and secure carriage bolts (13) with
Arc washers (15) and domed nuts (14).
B) Attach the front foot tube (2) to the main frame (1) fasten and secure carriage bolts (13) with
Arc washers (15) and domed nuts (14).
# STEP 2.
A) Hold the front post (4) and connect the middle computer sensor wire (29) and lower wire
end (30) individually as shown on diagram.
B) Insert the Front Post (4) onto the main body of the cross trainer ensure no wires are
pinched / trapped..
C) Fasten and secure with 4 Hex Bolts (16), 4 Arc washers(17), 4 Split Washers (17A).
7

# STEP 3.
A) Place the Left Foot Rail (7) on the rear disk of the main frame (1) then fasten and secure with
flat washers (23)(19) and Nylon Nut (20). Slide Lower Hand Rail-L (5) into the Left Foot Rail (7)
then Insert the Sleeve Tube (21). Insert Hex Bolt (18) through Flat Washer (19) and Sleeve Tube
(21) then Fasten and secure with flat washer (19) and Nylon Lock Nut (20).
B) Place the Right Foot Rail (8) on the rear disk of the main frame (1) then fasten and secure
with Flat washers (23)(19) and Nylon Nut (20). Slide Lower Hand Rail-R (6) into the Foot Rail
Right (8) then Insert the Sleeve Tube (21). Insert Hex Bolt (18) through Flat Washer (19) and
Sleeve Tube (21) then Fasten and secure with flat washer (19) and Nylon Lock Nut (20).
C) Attach the 4 PVC Cap (74) over the Hex Bolt(18) and Nylon Lock Nut (20). Tighten them by
Screw (26). Put the Foot Pad (L+R) (36) to the position you like and tighten with Flat washer (38)
and Knob (37). There are three position too choose from.
26
26
L
R
L
26
R
L
R
8

# STEP 4.
A) Connect right-hand pulse wire (31R + 32R) and left (31L + 32L) then insert the Front
handlebar (11) into the lower section and secure with 4 screws (26).
B) Connect computer sensor wire-upper portion (33) and middle Computer Wire (29). Connect
hand pulse upper wire (34) with the other section of the hand pulse middle wire (31 L+R) now
attach the computer (12) onto the plate on front post (4) and use 4 screws (39) to fasten.
# STEP 5.
A) Insert upper handlebar-L (9) to middle handlebar-L (5) then fasten and secure with round
head bolts (24) and Carriage Bolt (25).
B) Insert upper handlebar-R (10) to middle handlebar-R (6) then fasten and secure with round
head bolts (24) and Carriage Bolt (25).
C) Attach the Bottle Holder (80) on the front post with 2 screws (26).
D) Plug the Power Adaptor (35) into to the adaptor socket at the front of the unit then plug the
adaptor into your mains power socket.
Now you’re ready to use your Fusion Cross Trainer
9

COMPUTER INSTRUNCTION
FRONT VIEW
KEY GUIDE
ENTER/MODE:
1. Press this button to enter the function setting from Time, Distance, Calorie, and pulse limit.
2. Press this button to confirm the setting values.
UP :1. Press this button to select the program form Manual and Program 1 to Program 6.
2. Increase the setting value of Time, Distance, Calories, and Pulse Limit.
3. Increase the resistance level.
DOWN :1. Press this button to select the program form Manual and Program 6 to Program
1.
2. Decrease the setting value of Time, Distance, Calories, and Pulse Limit.
3. Decrease the resistance level.
START/STOP: 1. Press this button to start or stop exercising.
2. Hold this button for 2 seconds can enter initial mode and reset value to zero.
RECOVERY: StartsthefunctionofPULSERECOVERY.
POWER UP
1. Before all, you should connect the connection cables with monitor together.
2. If the power source is coming form ADAPTOR (6V 1A), plug in the ADAPTOR.
When stop exercising, please remember to unplug the ADAPTOR. (6V 1A)
3. After power up, all LCD segments will light up for 2 seconds & CPU will be reset the
resistance into level 0. And then the system goes into the initial mode.
10