Reebok RL 725 User manual

Serial No.
\Serial Number
Decal (on top
of the frame)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.-Fri., 6 a.m.-6 p.m. MST
_CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Patent Pending
ire at
_vw.reebokhomefitness.com
new products, prizes,
fitness tips, and much morel

IMPORTANT PRECAUTIONS ............................................................. 3
BEFORE YOU BEGIN ................................................................... 4
ASSEMBLY ........................................................................... 5
HOW TO USE THE CHEST PULSE SENSOR ................................................ 10
ELLIPTICAL EXERCISER OPERATION ..................................................... 12
MAINTENANCE AND TROUBLESHOOTING ................................................. 26
EXERCISE GUIDELINES ................................................................ 27
PART LIST ........................................................................... 29
EXPLODED DRAWING ................................................................. 30
ORDERING REPLACEMENT PARTS ................................................ Back Cover
LIMITED WARRANTY ........................................................... Back Cover
REEBOK and the Vector Logo _----_Z_"-are registered trademarks and service marks of Reebok. This product is
manufactured and distributed under license from Reebok International.

_WARN ING: To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual before 11. If you feel pain or dizziness while exercis-
using the elliptical exerciser, ing, stop immediately and begin cooling
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
in-home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
4. Place the elliptical exerciser on a level sur-
face, with a mat beneath it to protect the
floor or carpet. Keep the elliptical exerciser
indoors, away from moisture and dust.
down.
12. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended oniy
as an exercise aid in determining heart rate
trends in general.
13. When you stop exercising, allow the pedals
to slowly come to a stop. The elliptical exer-
ciser does not have a free wheel; the pedals
will continue to move until the flywheel
stops.
5. Inspect and properly tighten all parts regu- 14. The decal
lady. Replace any worn parts immediately, shown at
the right
6. Keep children under age 12 and pets away has been
from the elli ptical exerciser at all times, placed on
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
8. Wear appropriate exercise clothing when
using the elliptical exerciser. Always wear
athletic shoes for foot protection.
9. Always hold the handlebar when mounting
the ellipti-
cal exer-
ciser in the
indicated
location. If
the decal
is missing
or illegi-
ble, please
Or r_mOV_.
-i
or dismounting the elliptical exerciser.
Always hold the handlebar or the upper body
arms when using the elliptical exerciser.
10. Keep your back straight when using the ellip-
tical exerciser; do not arch your back.
call our Customer Service Department toll-
free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time, to
order a free replacement decal. Apply the
replacement decal in the location shown.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instruction s before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.

Congratulations for selecting the new REEBOK _ RL
725 elliptical exerciser. The RL 725 elliptical exerciser
is an incredibly smooth exerciser that moves your feet
in a natural elliptical path, minimizing the impact on
your knees and ankles. And the unique RL 725 fea-
tures adjustable resistance and a state-of-the-art con-
sole to help you get the most from your exercise.
Welcome to a whole new world of natural, elliptical-
motion exercise from REEBOK.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please call our
Customer Service Department toll-free at 1-800-999-
3756, Monday through Friday, 6 a.m. until 6 p.m.
Mountain Time (excluding holidays). To help us assist
you, please mention the product model number and
serial number when calling. The model number is
RBEL99020. The serial number can be found on a
decal attached to the elliptical exerciser (see the front
cover of this manual for the location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Upper Body Arm
Fan
Handlebar with
Bookrack
Console
Water Bottle Holder*
Upright FRONT
Pedal Cushion
Wheel
Pedal
Pedal Leg
BACK
RIGHT SIDE
Leveling Foot *No water bottle is included

Placeallpartsoftheellipticalexerciserinaclearedareaandremovethepackingmaterials.Donotdisposeof
thepackingmaterials until assembly is completed.
In addition to the included tools, assembly requires an adjustable wrench __ and a rubber
mallet -/ )"
Use the part drawings below to identify the small parts used in assembly. The number in parenthesis below
each drawing refers to the key number of the part, from the PART LIST on page 29. The second number refers
to the quantity used in assembly. Note: Some small parts may have been pre-assembled for shipping. If a
part is not in the parts bag, check to see if it has been pre-assembled.
\
Small M8
Washer (71)-2
\
MI0 Nylon M6 Split W/asher Large M8 Pedal Arm
Locknut (85)-4 (72)-2 Washer (70)-2 Spacer (65)-4
M4 x 16mm M4 x 19mm M4 x 25mm M6 x 20mm
Self=tapping Screw (92)-2 Screw (96)-2 Screw (75)-4
Screw (82)--6
M6 x 16mm Button
Screw (93)-2
M8 x 19mm Button M8 x 25mm Patch
Screw (81)-4 Screw (73)-12 Bolt Set (67)-2
1. Identify the Front Stabilizer (63), which has Wheels
(27) attached to one side. Attach the Front Stabilizer
to the front of the Frame (1) with four M8 x 25mm
Patch Screws (73).
73
5

2. Attach the Rear Stabilizer (24) to the rear of the
Frame (1) with four M8 x 25mm Patch Screws (73).
3. Remove the four M10 Nylon Locknuts (85) from the
welded bolts near the front of the Frame (1).
While a second person holds the Upright (2), con-
nect the Upper Wire Harness (15) to the Lower Wire
Harness (39).
Align the holes in the bracket on the lower end of the
Upright (2) with the welded bolts on the Frame (1).
Lower the Upright, feeding the Upper Wire
Harness (15) and the Lower Wire Harness (39) up
into the Upright, until the welded bolts are fully
inserted into the bracket. Be careful to avoid
pinching and damaging the Wire Harnesses.
Tighten the four M10 Nylon Locknuts (85) onto the
welded bolts on the Frame (1).
4. Feed the Upper Wire Harness (15) up through the
indicated hole in the Console Bracket (3). Attach the
Console Bracket to the Upright (2) with four M8 x
19mm Button Screws (81). Be careful to avoid
pinching and damaging the Upper Wire Harness.
Attach the Water Bottle Holder (13) to the Upright (2)
with two M4 x 19mm Screws (92). Note: The water
bottle holder is designed to be used with your own
water bottle.
73
//
/ / //
85
Be careful to
avoid pinching
and damaging the
Wire Harnesses
(15, 39) during
this step.
Welded
Bolts
Hole

5. 5 3
.
.
While another person holds the Handlebar (4) near
the Upright (2), feed the Pulse Sensor Wire (14) into
the Upright and out of the indicated hole in the
Console Bracket (3). Attach the Handlebar to the
Upright with two M6 x 16mm Button Screws (93)
and two M6 Split Washers (72). Be careful to
avoid pinching and damaging the Pulse Sensor
Wire.
Insert the Bookrack (7) into the slots in the Console
(8). Attach the Bookrack to the Console with two M4
x 25mm Screws (96). Be careful to avoid pinching
and damaging the wires in the Console.
While another person holds the Console (8) near
the Console Bracket (3), connect the Pulse Sensor
Wire (14) and the Upper Wire Harness (15) to the
corresponding wires on the Console.
Insert all excess wiring down into the Upright
(2). Attach the Console (8) to the Console Bracket
(3) with four M4 x 16mm Self-tapping Screws (82).
Be careful to avoid pinching and damaging the
Pulse Sensor Wire (14) and the Upper Wire
Harness (15).
93 72
Console
Wires
82
82

8. 8
InsertthePivotAxle(21)intotheUpright(2),and
centerthePivotAxle.Applyasmallamountofthe
includedgreasetobothendsofthePivotAxle.
IdentifytheLeftUpperBodyArm(5),whichis
markedwithadecal.InsertanUprightBushing(20)
intoanUprightSpacer(19).TurntheUpright
Spacersothatthesemicircularcutoutisatthetop,
andslidetheUprightSpacerontothepostonthe
LeftUpperBodyArm.
SlidetheLeftUpperBodyArm(5)ontothePivot
Axle(21).AttachaPivotSpacer(17)totheLeft
UpperBodyArmwithanM4x 16mmSelf-tapping
Screw(82).TurnaPivotEndcap(16)sothatthe
rectangularcutoutisatthebottom.Usingarubber
mallet,tapthePivotEndcapintothePivotSpacer.
SlideaSmallM8Washer(71)ontoanM8x25mm
PatchScrew(73),andtightenthePatchScrewinto
thePivotAxle(21).
Attach the Right Upper Body Arm (6) in the
same way.
.Apply a small amount of grease to the axle on the
left Crank Arm (40).
Identify the Left Pedal Leg (28), which is marked
with a decal. Slide the Left Pedal Leg onto the axle
on the left Crank Arm (40). Slide a Large M8
Washer (70) onto an M8 x 25mm Patch Screw (73),
and tighten the Patch Screw into the axle.
Snap a Pedal Cushion (74) around the Left Pedal
Leg (28) onto a Cushion Bracket (99). Make sure that
the arrow on the Pedal Cushion is pointing to one of
the numbers on the Left Pedal Leg and that the num-
ber shows through the window in the Cushion
Bracket.
Assemble the Right Pedal Leg (not shown) in the
same way.
10. Identify the Left Pedal Arm (33), which is marked
with a decal. Attach the Left Pedal (35) to the Left
Pedal Arm with two M6 x 20mm Screws (75) as
shown.
Attach the Right Pedal (not shown) to the Right
Pedal Arm (not shown) in the same way.
16
71
73
'9
10
17
82
19
Post
j
ii
//
20
Grease
74
28
Grease
Window
73 70
75
33

11.SettheLeftPedalArm(33)ontheleftPedalCushion
(74),andholdtheendoftheLeftPedalArminsideof
thebracketontheLeftPedalLeg(28).
HoldaPedalArmSpacer(65)betweentheLeftPedal
Leg(28)andtheLeftPedalArm(33).Insertthelong
partofaBoltSet(67)throughtheLeftPedalLeg,the
PedalArmSpacer,andtheLeftPedalArm.
LifttheLeftPedalLeg(28),andholdthelowerend
oftheLeftUpperBodyArm(5)insideofthebracket
ontheLeftPedalArm(33).Insertthelongpartofthe
BoltSet(67)throughtheLeftUpperBodyArm.Hold
anotherPedalArmSpacer(65)betweentheLeft
PedalArmandtheLeftPedalLeg,andinsertthe
longpartoftheBoltSetthroughtheseparts.Tighten
theshortpartoftheBoltSetintothelongpart.
Attach the Right Pedal Arm (32) in the same way.
11
65
67 28
65
74
32
12. Make sure that all parts are properly tightened before you use the elliptical exerciser. Note: Some
hardware may be left over after assembly is completed. Place amat under the exercise cycle to protect
the floor or carpet.

Togetthebestperformancefromthechestpulsesen-
sor,pleasereadtheinstructionsbelow.
HOWTOPUTONTHECHESTPULSESENSOR
Thechestpulsesensorconsistsoftwocomponents:
thecheststrapandthesensorunit.Followthesteps
belowtoputonthechestpulsesensor.
ChestStrap
P_-. Tab
_-Sensor __
Sensor Unit Buckle
Unit
_! Refer to the inset drawing above. Insert the tab
on one end of the chest strap through one end of
the sensor unit as shown. Then, press the end of
the sensor unit under the buckle on the chest
strap.
BWrap the
chest pulse
sensor
around
your chest.
Attach the
free end of
the chest
strap to the sensor unit as described above.
Adjust the length of the chest strap, if necessary.
The chest pulse sensor should be under your
clothing, against your skin, and as high under the
pectoral muscles or breasts as is comfortable.
Make sure that the logo is facing forward and is
right-side-up.
BPull the
sensor unit
away from
your body
a few inch-
es and
locate the
Electrode Areas
two electrode areas on the inner side. Using a
saline solution such as saliva or contact lens
solution, wet both electrode areas. Return the
sensor unit to a position against your chest.
CHEST PULSE SENSOR TROUBLESHOOTING
If the chest pulse sensor does not function proper-
ly, or if the displayed heart rate is excessively high
or low, try the steps below.
Make sure that the chest pulse sensor is worn
exactly as described in step 2 at the left. If the chest
pulse sensor does not function when positioned as
described, move it slightly lower or higher on your
chest.
Each time you use the chest pulse sensor, use
saline solution such as saliva or contact lens solu-
tion to wet the two electrode areas on the sensor
unit (see the drawing in step 3 below). If heart rate
readings do not appear until you begin perspiring,
re-wet the electrode areas.
Make sure that you are within arm's length of the
console. For the console to display heart rate
readings, the user must be within arm's length of
the console.
The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical condi-
tions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
magnetic interference may be causing a problem,
try relocating the elliptical exerciser.
• If the chest pulse sensor still does not function prop-
erly, test the chest pulse sensor in the following way:
Hold the chest
pulse sensor
and place your
thumbs over
the electrode
areas as
shown.
Electrode Areas
10