ReelCraft 5600 OLB User manual

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
Operating Instructions
Series 5000 Spring Driven Hose Reels
Low Pressure Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 581-1091 Rev: 2/2014
Dimensions
A14 3/8”
B 14”
C9 3/4”
D2 1/2”
E6 1/8”
5600 OLB
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.

Series 5000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Specifications
Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description
1 300031 2 1” Snap Ring 12 S300011 7 10-32 Hex Lock Nut 23 400020 5 O-ring
2 300034 2 Spacing Washer 13 S504240 1 Drive Spring Assembly 24 S400109 1 Latch Plate Assembly
3 S295-102 3 1/4” Plastite Hex Screw 14 S261360 1 Spring Case Stud 25 300035 1 10-32 x 1” Mach. Screw
4 260022 1 Sheave Flange 15 300006 1 3/8-16 x 1/2” Set Screw 26 3-117440 1 U-bolt
5 500006 1 Sheave Disk 16 S500103 1 Spring Case Assembly 27 261650-1 2 1/4-20 Zinc Nyloc Nut
6 S50019 1 Latch Cam 17 S82-15 1 10-32 x 3/8” Nyloc Nut 28 260227-B 1 Main Shaft
7 S260648 1 Spring Arbor 18 S400021 1 Latch Bumper 29 600374-1B 1 Swivel Assembly
8 300002 2 10-32 x 1/2” Screw 19 S32-136 1 10-24 x 3/8” Mach. Screw 30 S160-3 1 Street Ell
9 1-HR1004A 1 Hose Bumper Assembly 20 S400012 1 Latch Bushing
10 S500107 1 Guide Arm & Roller Assembly 21 S400018 1 Latch Spring
11 500101 1 Base Assembly 22 300001 1 10-32 x 3/8” Screw
Hose I.D. and Length None
Reel Inlet Connection 3/8” F.P.T.
Max. Operating Pressure 300 P.S.I.
Max. Operating Temperature 210° F