ReelCraft 4000 Series User manual

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
4425 OLPSMR 4435 OLPSMR 4625 OLPSMR
4425 OLPSML 4435 OLPSML 4625 OLPSML
Operating Instructions
Series 4000 Spring Driven Hose Reels
Side Mount Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 1230-1011 Rev: 4/2013
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
Dimensions
ABCDE
5 2/3” 12 1/4” 14” 12” 1 1/4”

Series 4000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Part # # Req. Description Item #Part # # Req. Description Item #Part # # Req. Description
1 S300011 1 Machine Screw 11 3-117440 1 U-Bolt 21 300002 2 Machine Screw
2 S400109 1 Latch Plate Assembly 12 S400019 1 Latch Cam 22 S82-15 4 Lock Nut
3 S400012 1 Latch Bushing 13 S260648 1 Spring Arbor 23 262503 1 Side Mount Plate
4 S400018 1 Latch Plate Screw 14 S300011 7 Hex Lock Nut 24 300001 5 Machine Screw
5 S32-136 1 Self Tapping Screw 15 262493 1 Spring Case Cover 25 S82-15 1 Lock Nut
6 S400021 1 Latch Plate Bumper 16 300031 1 Snap Ring 27 S400015 1 Main Shaft
7 602330 1 Swivel Assembly 17 300034 2 Wear Washer 28 S137-12 1 Snap Ring
8 S295-102 3 Self Tapping Screw 18 S261360 1 Spring Case Stud 29 S400107 1 Guide Arm
9 400005 1 Sheave Flange 19 602434 1 Spring Case Assembly 30 262493 1 Sheave Disc
10 261650-1 2 Lock Nut 20 300006 1 Set Screw
Item
#Description # Req. 4425 OLPSMR 4425 OLPSML 4435 OLPSMR 4435 OLPSML 4625 OLPSMR 4625 OLPSML
26 Drive Spring Assembly 1 400020 400020 S400030 S400030 S404230 S404230
Hose Assembly 1 601001-25 601001-25 601001-35 601001-35 601013-25 601013-25
Hose Bumper Assembly 1 A1-HR1004-A A1-HR1004-A A1-HR1004-A A1-HR1004-A A1-HR1004 A1-HR1004
Max. Operating Pressure 300 PSI 300 PSI 300 PSI 300 PSI 300 PSI 300 PSI
Max. Operating Temperature 150° F 150° F 150° F 150° F 150° F 150° F