ReelCraft D8600 OLP Use and care manual

Form No. 4768-84
Revised: 10/09
II.
I.
Remove all spring tension before beginning
disassembly process.
Do not use reels at higher pressures or temperatures
than listed on the back of this bulletin.
Safety
Hose Reel
Operating Instructions and Parts List
Low Pressure
Model Series D8000
Four 1/2" diameter mounting slots
Reelcraft Industries, Inc. • [phone] / [phone] • Fax: [phone]
[email protected] • www.reelcraft.com
Instructions
Installation: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent
possible misalignment and binding.
Mounting: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
Lubrication: Hose reel spring and bearings are factory lubricated and require no further lubrication.
Replacing
Hose:
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide and hole in spool flange.
4. Connect hose fitting to swivel joint and secure hose with clamps.
Adjustments: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension
is obtained.
Repairs: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
A21 1/4”
B19”
C7 7/8”
D3 3/4”
E9 1/4”
Caution: When changing guide arm positions, the U-bolt must be placed
in the proper location as instructed. The reel can "latch out" during use if this
instruction is not adhered to.
D8600 OLP
D8640 OLP
D8650 OLP
D8670 OLP
D8800 OLP
D8830 OLP
D8840 OLP
D8850 OLP

Reelcraft Industries, Inc. • [phone] / [phone] • Fax: [phone]
[email protected] • www.reelcraft.com
1
2
345678910
11 12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Item
#Part No. No. Req. Description Item #Part No. No. Req. Description Item #Part No. No. Req. Description
2600923 1Swivel Ass’y 12 S260045 1Guide Roller & Pin Kit 20 300042 110-24 x 1” Screw
3260011 1Sheave Ass’y 13 260007 1Guide Arm Ass’y 21 S600083 1Latch Pawl Ass’y
5S600621 1Spring Arbor Ass’y 14 507286 35/16-18 x 1¼” Screw 22 S76-106 13/8-24 Hex Jam Nut
6S260069 1Gasket 15 S35-86 11/2-13 Set Screw 23 S260031 1Spring Case Stud
7S260074 1Spring Case Ass’y 16 S280-8 11/2-20 Hex Nut 25 300070 41/4-20 Nyloc Nut
8300011 610-32 Hex Nut 17 260073 1Base Casting 26 300039 4Washer
9260442 1Main Shaft 18 S260067 1Latch Spring 27 S257-26 1Swivel Union
10 300007 31¼” Snap Ring 19 S400012 1Latch Bushing
Item
#Description No. Req. Model D8600 OLP Model D8640 OLP Model D8650 OLP Model D8670 OLP Model D8800 OLP Model D8830 OLP Model D8840 OLP Model D8850 OLP
1Hose Ass’y 1None 601014-40 601017-50 601017-70 None 601021-30 601019-40 601021-50
4Drive Spring Ass’y 1S260028 S260028-1 S260028-1 S260028 S260037 S260037 S260037 S260037
11 Hose Bumper 1None 1-HR1004-3 1-HR1004-3 1-HR1004-3 None 2-HR1004-3 2-HR1004-3 2-HR1004-3
24 U-bolt 22-117440 2-117440 2-117440 2-117440 3-117440 3-117440 3-117440 3-117440
Hose I.D. & Length None 3/8” x 40’ 3/8” x 50’ 3/8” x 70’ None 1/2” x 30’ 1/2” x 40’ 1/2” x 50’
Reel Inlet Connection 1/2” F.P.T. 1/2” F.P.T. 1/2” F.P.T. 1/2” F.P.T. 1/2” F.P.T. 1/2” F.P.T. 1/2” F.P.T. 1/2” F.P.T.
Maximum Operating Pressure 500 P.S.I. 300 P.S.I. 300 P.S.I. 300 P.S.I. 500 P.S.I. 300 P.S.I. 300 P.S.I. 300 P.S.I.
Maximum Operating Temperature 210° F 150° F 150° F 150° F 210° F 150° F 150° F 150° F