ReelCraft 5000 Series User manual

INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Operating Instructions
Series 5000 Spring Driven Hose Reels
Side Mount Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 1231-1011 Rev: 4/2013
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
5450 OLPSMR 5635 OLPSMR A5825 OLPSMR
5450 OLPSML 5635 OLPSML A5825 OLPSML
Dimensions
ABCDE
6 1/8” 13 7/8” 15 1/4” 13 1/2” 1 1/4”
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY

Series 5000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Part # # Req. Description Item #Part # # Req. Description Item #Part # # Req. Description
1 300035 1 Machine Screw 12 S500019 1 Latch Cam 22 S82-15 4 Lock Nut
2 S400109 1 Latch Plate Assembly 13 S260648 1 Spring Arbor 23 262488 1 Side Mount Plate
3 S400012 1 Latch Bushing 14 S300011 7 Hex Lock Nut 24 300001 5 Machine Screw
4 S400018 1 Latch Plate Screw 15 262494 1 Spring Case Cover 25 S82-15 1 Lock Nut
5 S32-136 1 Self Tapping Screw 16 300031 1 Snap Ring 27 S400015 1 Main Shaft
6 S400021 1 Latch Plate Bumper 17 300034 2 Wear Washer 28 S137-12 1 Snap Ring
8 S295-102 3 Self Tapping Screw 18 S261360 1 Spring Case Stud 29 S500107 1 Guide Arm
9 260022 1 Sheave Flange 19 602435 1 Spring Case Assembly 30 500006 1 Sheave Disc
10 261650-1 2 Lock Nut 20 300006 1 Set Screw
11 3-117440 1 U-Bolt 21 300002 2 Machine Screw
Item
#Description # Req. 5450 OLPSMR 5450 OLPSML 5635 OLPSMR 5635 OLPSML A5825 OLPSMR A5825 OLPSML
7 Swivel Assembly 1 602330 602330 602330 602330 602444 602444
26 Drive Spring Assembly 1 S503755 S503755 S504240 S504240 S505740 S505740
Hose Assembly 1 601001-50 601001-50 601013-35 601013-35 601020-25 601020-25
Hose Bumper Assembly 1 A1-HR1004-A A1-HR1004-A A1-HR1004 A1-HR1004 A2-HR1004-3 A2-HR1004-3
Max. Operating Pressure 300 PSI 300 PSI 300 PSI 300 PSI 300 PSI 300 PSI
Max. Operating Temperature 150° F 150° F 150° F 150° F 150° F 150° F