Regalo Easy Step User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
Easy Step
Safety Gate
OWNER’S MANUAL MODELS: 1160, 1164 EW/EB/EP, 1165W
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English 3
Before Using Product
Read and follow all instructions carefully to ensure that your gate and extensions
are properly installed. Improper installation could result in the gate becoming
unstable or dislodged from the doorway. Always make sure the extension is securely
attached to the gate before using. The safety of your child is your responsibility.
Please keep these instructions for your reference.
IMPORTANT
• NEVER use more than two extensions per side of gate.
• If hardware mounting to a surface other than drywall or wood,
please consult with a professional about installation.

English4
WARNING
• To prevent serious injury or death, securely install gate
or enclosure and use according to manufacturer's
instructions.
• Children have died or been seriously injured when
gates are not securely installed. ALWAYS install and
use as directed using all required parts.
• STOP using when a child can climb over or dislodge
the gate.
• Use only with the locking mechanism securely
engaged.
• To prevent falls, NEVER use at top of stairs.
• NEVER use to keep child away from pool.
• Intended for use with children from 6 months
through 24 months.
• Always ensure the gate is resting against the floor
before beginning installation.
• This product will not necessarily prevent all accidents.
Never leave child unattended.
• Check the gate regularly to see if all the hardware and
mountings are tightened.
• Do not use if any component is missing or damaged.
• Adult assembly required.

English 5
PLEASE CHECKTO MAKE SUREYOU HAVE THE FOLLOWING PARTS:
A Gate Frame (1)
B Wall Cups (4)
C Screws (4) (requires a Phillips/cross-head screwdriver)
D Threaded Spindle Rods (4)
Before Assembly
A
D
C
B

English6
MODEL NO. MAX SIZE
1160
1164 EW/EB/EP
1165W
29 –38.5 inches
29 –51 inches
29 –44 inches
Extensions List
NOTE
NOTE: When installing any gate at its maximum width, use wall cups to
ensure stability and safety.
4" 6" 8" 12"
WARNING: The gap between the gate and wall should not exceed
more than 2.5 inches.

English 7
STEP 1
Locate the (4) threaded
spindle rods. Rotate the
adjustment wheels along
the threading, eliminating the
gap between the adjustment
wheel and the rubber foot.
Assembling and InstallingYour Gate
STEP 2
Insert the (4) threaded
spindle rods into the holes
at each of the four corners
of the gate.
NOTE: You will notice a slight gap between the gate door latch and the
frame. This is not a defect. Your gate is a pressure mounted gate and this
gap will disappear once you tighten your gate in its opening.
RUBBER FOOT
ADJUSTMENT WHEEL

English8
NOTE: It may be necessary to hold the threaded spindle rods or rubber feet
while rotating the adjustment wheels to ensure the entire unit does not rotate.
STEP 3
Position the gate so that it is level and centered within your doorway or
opening. Rotate the adjustment wheels on the threaded spindle rods in the
opposite direction as in STEP 1, expanding the gap between the rubber foot
and the adjustment wheel. Expand each of the (4) threaded spindle rods
until they make contact with the doorway or opening. Do not fully tighten the
threaded spindle rods yet.

English 9
STEP 4
When you are satisfied with the general placement of your gate, fully
tighten the threaded spindle rods attached to the lower corners of the gate
by further rotating the adjustment wheels.
Continue by tightening the upper threaded spindle rods. As you tighten
the upper threaded spindle rods, you will notice the gap between the door
frame and the easy open latch begin to narrow.
In order for the gate to function properly, stop tightening the upper
threaded spindle rods just before the inner wall of the locking latch and
the gate frame touch.
NOTE: There should be equal spacing among each of the (4) threaded
spindle rods. Make the appropriate adjustment to ensure you have installed
your gate safely.
LOCKING LATCH
GATE FRAME

English10
Positioning and Attaching the Wall Cups
STEP 1
After you have mounted your gate, and you are satisfied with its positioning,
draw a circle on the surface of your doorway or opening around the perimeter
of the (4) rubber feet.
STEP 2
Next, completely remove the gate from the opening by loosening each of the
(4) threaded spindle rods to depressurize the gate.
Your gate is a pressure mounted gate. Therefore, it is not necessary to use the
screw attached wall cups in your door opening if you choose not to. However, if you
are using the gate at the top of the stairs you must use the wall cups. Using the
wall cups will affix your gate more firmly in the doorway or opening.

English 11
STEP 3
With the gate fully removed, you can now use the circles you marked during
STEP 1 as guides for screwing in your (4) wall cups.
Center each of the wall cups within the guide circles and use the provided
self-tapping screws to fasten them in place via the hole through the center of
each wall cup.
STEP 4
Reinstall your gate in the doorway or opening according to the instructions,
using the newly installed wall cups as anchoring points for the (4) threaded
spindle rods.

English12
Operating the Door Latch
STEP 1
Pull the spring lock away from the easy open latch while simultaneously lifting
the lock lever upwards. This will release the locking latch from the gate frame
and allow the door to push or pull open.
STEP 2
To lock the door shut, close the door completely, then push down on the lock
lever to re-engage the spring lock.
NOTE: If your easy open latch is not properly engaging with the receiving
component, ensure that your gate is level, mounted properly, and that you
have not over-tightened the threaded spindle rods.
LOCK LEVER
SPRING LOCK

English 13
Adding a Gate Extension
STEP 1
Choose the side of the gate to be extended and remove the top and bottom
threaded spindle rods.
STEP 2
Assemble the gate and extension as illustrated. Reposition the gate and fit in
accordance with the gate fitting instructions.
NOTE: It is preferable to install any extensions on the hinge side of the gate.
If you have an application that requires additional extensions, please
contact the manufacturer.

English14
REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the
(4) threaded spindle rods to depressurize the gate from its doorway or opening.
Then, gently pull or push the gate free from its doorway or opening.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 15
Replacement Parts
A Easy Open Latch
Gray = #14037
Black = #11037
White = #13037
B Top Plug Insert
Gray = #14020
Black = #11020
C Threaded Spindle Rods
w/Adjustment Wheel
Gray = #14016
Black = #11016
D 1" Wall Mount Screws
#10001
E Wall Cups
Gray = #14015
Black = #11015
F Bottom Plug Insert
Gray = #14019
Black = #11019
A
F
B C D E

French16
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, É.-U.
866.272.5274 (aux États-Unis seulement) ou 952.435.1080
Fabriqué en Chine
Barrière de sécurité
à ouverture facile
GUIDE D’UTILISATION MODÈLES:1160, 1164 EW/EB/EP, 1165W
• LIRE TOUTES LES INSTRUCTIONS AVANT D’ASSEMBLER ET
D’UTILISER LA BARRIÈRE.
• CONSERVER CES INSTRUCTIONS POUR UNE UTILISATION
ULTÉRIEURE.

French 17
Avant d’utiliser le produit
Lire et suivre attentivement les instructions pour assurer une installation conforme
de la barrière et des rallonges. Une mauvaise installation risque d’aboutir à une
barrière branlante, ou qui se détache de l’ouverture. Avant utilisation, toujours
s’assurer que la rallonge est fixée solidement à la barrière. Vous êtes responsable
de la sécurité de votre enfant. Conserver ces instructions pour consultation.
IMPORTANT
• Ne jamais utiliser plus de deux rallonges par côté de barrière.
• Si la surface de fixation n’est pas une cloison sèche ou du bois, consulter un
spécialiste au sujet de l’installation.

French18
MISE EN GARDE
• Pour prévenir des blessures graves voire mortelles,
assembler solidement la barrière ou le parc; leur
utilisation doit être conforme aux directives du
fabricant.
• Des enfants sont morts ou ont subi de graves
blessures en raison de barrières et de parcs mal fixés.
TOUJOURS installer et utiliser les barrières et les parcs
conformément aux directives en utilisant toutes les
pièces nécessaires.
• CESSER l'utilisation si un enfant est capable de grimper
par-dessus la barrière ou le parc ou de les déloger.
• Installer de façon que le mécanisme de verrouillage se
trouve du côté opposé à l'enfant.
• Pour éviter les chutes, ne jamais utiliser la barrière en
haut des escaliers.
• NE JAMAIS utiliser pour tenir les enfants à l'écart d'une
piscine.
• Destiné aux enfants de 6 à 24 mois.
• Toujours s'assurer que la barrière repose sur le sol
avant de commencer l'installation.
• Cet article ne prévient pas nécessairement tous les
accidents. Ne jamais laisser l'enfant sans surveillance.
• Vérifier régulièrement le serrage des pièces de
montage et de fixation.
• Ne pas utiliser s'il manque des pièces ou elles sont
endommagées.
• Assemblage adulte requis.

French 19
VEUILLEZ VÉRIFIER QUE VOUS DISPOSEZ DES ARTICLES SUIVANTS:
A Cadre de barrière (1)
B Coupelles murales (4)
C Vis (4) (tournevis cruciforme/Phillips requis)
D Tiges filetées (4)
Avant l’assemblage
A
D
C
B

French20
NODE MODÈLE DIMENSIONS MAXIMUM
74 cm à 97 cm
74 cm à 129 cm
74 cm à 112 cm
Liste des rallonges
REMARQUE
REMARQUE : Si l’on déploie la barrière à sa largeur maximale, utiliser les
coupelles murales pour assurer la stabilité et la sécurité.
10 cm 15 cm 20 cm 30 cm
MISE EN GARDE : La distance entre la barrière et le mur ne doit
pas être supérieure à 6 cm (2,5 po) sur l’un ou l’autre des côtés de la barrière.
1160
1164 EW/EB/EP
1165W