Regency Fireplace Products E33-NG10 Service manual

REGENCY FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4
919-379 11.03.14
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
E33 Gas Insert
Owners & Installation Manual
MODELS: E33-NG10 Natural Gas E33-LP10 Propane
- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach you gas supplier, call the re department.
- Installation and service must be performed by a qualied installer, service agency or the gas supplier.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

2| E33-10 FPI Direct Vent Gas Insert
|
2
REGENCY GAS FIREPLACE INSERT
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Gas Insert by Regency.
The E33 Gas Insert has been designed to provide you with all the warmth and charm of a replace, at
the ick of a switch. The E33-NG10 and E33-LP10 have been approved by Warnock Hersey/Intertek
for both safety and efciency. As it also bears our own mark, it promises to provide you with economy,
comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself
with these instructions and the many features of your Regency Fireplace.
Energy E33 Video

E33-10 FPI Direct Vent Gas Insert | 3
| 3
dimensions
28 11
16
"
42 7
16
"
26 3
4
"
16 1
4
"
23 3
4
"
11 1
16
22 3
4
"
46 1
2
"
(1181mm)
(1078mm)
(679mm)
(729mm)
(281mm)
(413mm)
(603mm)
(578mm)
"
31
4
"
13
4
(83mm)
(44mm)
32-1/4”
819mm
24-1/2”
(622mm)
optional spacer
Oversized Faceplate Dimensions" 49-9/16" x 33-1/8" H

4| E33-10 FPI Direct Vent Gas Insert
|
4table of contents
Dimensions....................................................................3
Safety Decal ..................................................................5
MA Code - CO Detector.................................................6
Important Message ......................................................7
For Your Safety..............................................................7
Before You Start ............................................................7
Gas Pressure Testing ....................................................8
Specications ................................................................8
Installation Into A Solid Fuel Burning Fireplace
Or Factory Built Fireplace..............................................8
Installation Checklist.....................................................8
Materials Required ........................................................8
Gas Insert Aeration System...........................................9
Minimum Fireplace Opening..........................................9
Minimum Clearances To Combustibles .......................10
Combustible Mantel Clearances................................10
Gas Connection .......................................................... 11
Venting......................................................................... 11
Flue Liner Installation .................................................. 11
Remote Receiver Installation.......................................12
Gas Pipe Pressure Testing ..........................................12
SIT 829 Valve Description ...........................................12
DC Spark Igniter Battery Installation ...........................12
Optional Brick Panel....................................................12
Log Set Installation......................................................14
Conversion from NG to LP ..........................................17
Low prole Faceplate Installation ................................18
Optional Backing Plate Installation..............................20
Safety Screen Installation............................................21
Standard Flush Door ...................................................21
Wiring Diagram............................................................22
First Fire ......................................................................23
Operating Instructions .................................................23
Lighting Procedure ......................................................23
Shutdown Procedure...................................................23
DC Spark Igniter Battery Installation ...........................23
Copy of Lighting Instruction Plate................................24
Automatic Convection Fan Operation..........................24
Normal Operating Sounds Of Gas Appliances ............24
Maintenance Instructions.............................................25
General Vent Maintenance ..........................................25
Log Replacement ........................................................25
Glass Gasket...............................................................25
Door Glass ..................................................................26
Fan Maintenance.........................................................26
Valve Assembly Removal And Installation...................27
Main Assembly ............................................................28
Burner & Log Assembly ...............................................29
Low prole faceplate ...................................................30
Warranty ......................................................................31

E33-10 FPI Direct Vent Gas Insert | 5
| 5
safety decal
This is a copy of the labels that accompany each E33 Gas Insert. We have printed a copy of the contents here for your review. The safety label is located
on a plate inside the base of the unit visible when the bottom louver is opened. Ensure that the safety label is attached to the unit.
NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
Fan Part No. 910-331/P
ELECTRICAL SUPPLY/ALIMENTATION ELECTRIQUE:
115V60HZ less than/Moins de 2 AMP.
NOT FOR USE WITH SOLID FUEL/ NE PAS UTILISER
AVEC DU COMBUSTIBLE SOLIDE.
Minimum Clearances to Combustibles from Insert
Side Walls *A 8" (203mm)
Ceiling B 47" (1194mm)
Min. Mantel Height C 15" (381mm)
Max. Mantel Depth D 3½" (89mm)
D
E
F
H
G
A
B
CI
MADE IN CANADA /FABRIQUE AU CANADA
Mantel Clearances
DO NOT REMOVE THIS LABEL /
NE PAS ENLEVER CETTE ETIQUETTE
Serial No. / No de serie
Duplicate Serial number
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and
Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not
applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard
for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured
(mobile) home where not prohibited by local codes. See owner's manual for details.
W:ARNING This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original
parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel
Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part
3280, Manufactured Home Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA
501A, Manufactured Home Installations Standard, ouANSI A119.2 ou NFPA501C Standard for Recreational Vehicles.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
AVERTISSEMENT: Ce foyer a été converti pour utilisation avec un foyer au gaz encastrable et ne peut être utiliser pour brûler du bois ou d'autres
combustibles solides à moins que toutes les pièces d'origine aient été remplacées et que le foyer ait été approuvé de nouveau par l'autorité compétente.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
For use with glass doors certified with the appliance only Pour utilisation uniquementavec les portes en verre certifiées avec l'appareil
VENTED GAS FIREPLACE HEATER -FOYERAUNOT FOR USE WITH SOLID FUELS. /
GAZ À ÉVACUATION - NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE.
ÉÉQUIP AL'UISINE POUR GAZ PROPANE
ÉÉQUIP AL'UISINE POUR GAZ NATURAL
FPI Fireplace Products International Ltd.,
Delta BC, CANADA
Pression d'allimentation minimum
Pression la tubulure d' chappement basse
àé
Pression la tubulure d' chappement lev e
àééé
Dimensions de l'orifice
D bit Calorifique minimumé
D bit Calorifique maximumé
Pression d'allimentation minimum
Pression la tubulure d' chappement basse
àé
Pression la tubulure d' chappement lev e
àééé
Dimensions de l'orifice
D bit Calorifique minimumé
D bit Calorifique maximumé
298
298
Model/Modele:
E33-NG10
919-378
Model/Modele:
E33-LP10
NATURAL GAS FIREPLACE INSERT: MODEL E33-NG10
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure 5“ WC (1.25 kpa)
Low Setting Man. Pressure 1.1" WC (0.27 kpa)
Max. Manifold Pressure 3.8" WC (0.95 kpa)
Orifice Size 31 DMS
Minimum Input 20,000 Btu/h (5.86 kW)
Maximum Input 38,000 Btu/h (11.13 kW)
PROPANE GAS FIREPLACE INSERT: MODEL E33-LP10
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure 12" WC (2.99 kpa)
Low Setting Man. Pressure 2.9" WC (0.72 kpa)
Max. Manifold Pressure 11"WC (2.74 kpa)
Orifice Size 50 DMS
Minimum Input 19,000 Btu/h (5.56 kW)
Maximum Input 35,500 Btu/h (10.4 kW)
Alcove Width E 76" (1930mm)
Alcove Depth F 36" (914mm)
Non-Combustible Hearth Extension
Hearth Height G 1-1/4" (32mm)
Hearth Width H 45-1/2" (1156mm)
Hearth Depth I 13" (330mm)
* Alcove side wall must have a
min. of 8” clearance on one side.
4001172
For Use Only with Barrier (Part # 342-013) Follow installation instructions.
Utiliser uniquement avec l’écran ( n ° 342-013) Suivre les instructions d'installation.
Listed: VENTED GAS FIREPLACE HEATER
/ FOYER AU GAZ À ÉVACUATION
CANADA and U.S.A.Certified for/Certifi e pour:é
Certified to: CAN/CGA-2.17-M91(R2009)
Tested :to ANSI Z21.88-20 CSA 2.33-2014 &14

6| E33-10 FPI Direct Vent Gas Insert
|
6requirements
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

E33-10 FPI Direct Vent Gas Insert | 7
| 7
installation
Fuel Gas Code ANSI Z223.1 in the U.S.A. This
appliance should be installed by a qualied gas
tter technician only.
2) Installation and repair should be done by a
qualied service person.
3) The appliance should be inspected before use
and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, animal hair, etc. It is imperative that
control compartments, burners and circulating
air passageways of the appliance be kept clean.
4) See general construction and assembly
instructions. This appliance may only be
installed in a vented, noncombustible replace.
5) This appliance isListed for bedroom installations
when used with a Listed Millivolt Thermostat.
Some areas may have further requirements,
check local codes before installation.
6) Always connect this insert to a vent system
venting to the outside of the building envelope.
Never vent to another room or inside a building.
Make sure that the vent is properly sized and is
of adequate height to provide the proper draft.
7) Inspect the venting system annually for
blockage and any signs of deterioration.
8) Any glass removed for servicing must be
replaced prior to operating the appliance.
9) To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the replace.
10) Due to high temperatures, the appliance should
be located out of high trafc areas and away
from furniture and draperies. Children and
adults should be alerted to the hazards of high
surface temperatures, especially the replace
glass and gold trims, and should stay away to
avoid burns or clothing ignition. Young children
should be carefully supervised when they are
in the same room as the appliance. Clothing or
other ammable material should not be placed
on or near the appliance.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The Regency Gas Insert must be installed in
accordance with these instructions. Carefully read
all the instructions in this manual rst. Consult the
building authority having jurisdiction to determine
the need for a permit prior to starting the installation.
NOTE: Failure to follow the instructions could cause
a malfunction of the heater which could result in
death, serious bodily injury, and/or property damage.
Failure to follow these instructions may also void
your re insurance and/or warranty.
FOR YOUR SAFETY
This appliance requires air for proper combustion.
Always provide adequate combustion and
ventilation air. Follow instructions and information
in CAN/CGA B149 (in Canada) or the National Fuel
Gas Code ANSI Z223.1 (in the USA), regarding
requirements for combustion and ventilation air.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAYTO AVOID BURNS
OR CLOTHING IGNITION.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC.IT IS IMPERATIVETHAT
CONTROL COMPARTMENTS,BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI-
ANCE. TODDLERS,YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND-
ED IFTHERE ARE AT RISK INDIVIDUAL
INTHE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI Stand-
ards to make you aware of the following:
General Safety Information
1) The appliance installation must conform with
local codes or in the absence of local codes,
with CAN/CGA B149 (in Canada) or the National
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE HOT
VIEWING GLASS IS PROVIDED WITH
THIS APPLIANCE AND SHALL BE
INSTALLED FOR THE PROTECTION
OF CHILDREN AND OTHER AT-RISK
INDIVIDUALS
IFTHE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITHTHE MANUFACTURER'S BARRIER
FOR THIS APPLIANCE.
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
AN APPLIANCE MUST BE REPLACED
PRIORTO OPERATINGTHE APPLIANCE. For the State of Massachusetts, installation
and repair must be done by a plumber or
gastter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, exible con-
nectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances
individual manual shut-off must be a t-handle
type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.

8| E33-10 FPI Direct Vent Gas Insert
|
8installation
GAS PRESSURE
TESTING
The appliance must be isolated from the gas supply
piping system by closing its individual manual
shut off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than
1/2 psig. (3.45 kPa).
SPECIFICATIONS
At pressures over 1/2 psig, the pipe to the unit
must be disconnected.
Gas Input Capacity:
Natural Gas 38,000 Btu/h
Propane 35,500 Btu/h
Min. Input:
Natural Gas 20,000 Btu/h
Propane 19,000 Btu/h
Fuels: Approved for use with both natural gas,
and propane. Approved as is for use at 0' to 4,500'
(0-1370m).
Electrical: 120V A.C. system.
Circulation Fan: Variable speed, 127 CFM.
Log Set: Ceramic bre, 8 per set.
Vent System: 3" co-linear aluminum ex.
INSTALLATION INTO A SOLID
FUEL BURNING FIREPLACE
OR FACTORY BUILT
FIREPLACE
The E33 Gas Inserts have been tested and
approved to be vented into any masonry replace
or approved solid fuel burning factory built
replace that will allow the insert to physically t
into the rebox. Refer to the "Minimum Fireplace
Dimensions" section.
If the factory built replace* height is too low
for your Insert, you may remove the smoke
bafe plate and damper from the factory built
replace as long as these items are saved and
are reinstalled in the event that the Insert is
removed. NOTE: Any alterations made to the
listed solid fuel burning factory built replace
may void the listing of the replace. Cutting
any sheet-metal parts of the replace, in which
the gas replace insert is to be installed, is
prohibited.
If the factory-built replace has no gas access
hole(s) provided, an access hole of 1.5"
(37.5mm) or less may be drilled through the
lower sides or bottom of the rebox in a proper
workmanship like manner. This access hole
must be plugged with non-combustible
insulation after the gas supply line has been
installed.
The fireplace and fireplace chimney must
be clean and in good working order and
constructed of non-combustible materials and
chimney cleanouts must t properly. Refractory,
glass doors, screen rails, screen mesh, and
log grates can be removed from the replace
before installing the gas replace insert. Smoke
shelves, shields and bafes may be removed
if attached by mechanical fasteners. A tight
connection between the gas replace insert ue
collar and the replace chimney must be made.
*Check with your local inspector before commencing
with this installation.
INSTALLATION
CHECKLIST
Before installing vent system ensure that the damper
plate is open and secure to prevent the damper plate
from falling down and crushing the liner.
The Regency Gas Insert is installed as listed below.
1) Check all clearances to combustibles. Refer
to the following sections where applicable:
a. Minimum Clearances to Combustibles.
b. Regency Flush Combustible Mantel
Clearances
c. Mantel Clearances
2) Make the gas connection. Refer to the "Gas
Connection" section.
3) Install the 3" ue liner to the sliding connector
plate. Refer to the "Flue Liner Installation"
section.
4) Slide the unit half way into the replace.
5) Pull the vent connector plate through the tapered
brackets and fasten to the front plate. Refer to
the "Flue Liner Installation" section.
6) Slide the unit fully into the replace.
7) Install 4AA batteries into receiver. Hook receiver
to wire marked receiver, this will enable
operation of the appliance manually when
position in "ON" position.
8) Test gas pressure, refer to the "Gas Pipe
Pressure Testing" section. Check aeration
system, refer to "Gas Insert Aeration Systems"
section.
9) Install standard and optional features. Refer
to the following sections where applicable:
a. Brick Panels
b. Log Installation
c. Faceplate
d. Standard Flush Door
e. Remote Control
10) Final check. Refer to the "Final Check"
section. Before leaving this unit with the
customer, the installer must ensure that the
appliance is ring correctly. This includes:
a) Clocking the appliance to ensure the
correct ring rate.
b) Adjusting the primary air, if required, to
ensure that the ame does not carbon.
Refer to the "Gas Insert Aeration
System" section.
c) Ensuring that the appliance is venting
correctly.
MATERIALS
REQUIRED
No electrical power supply is required for the gas
control to operate. A 120 Volt AC power cord is
hooked up to the fan. Plug the 3 wire cord into
a suitable receptacle. Do not cut the ground
terminal off under any circumstances. When
connected with 120 volts, the appliance must be
electrically grounded in accordance with local
codes, current version of the Canadian Electrical
Code CSA C22.1 (in Canada) or in the absence
of local codes, with the National Electrical Code
ANSI/NFPA 70.
NOTE: This unit is equipped with a heat
sensor thermodisc which will prevent the
blower from operating until the unit reaches
the correct temperature.
Installer must mechanically attach the supplied
label to the inside of the rebox of the replace
into which the gas replace insert is installed.
"WARNING: This fireplace has been
converted for use with a gas replace insert
only and cannot be used for burning wood or
solid fuels unless all original parts have been
replaced, and the replace re-approved by
the authority having jurisdiction."

E33-10 FPI Direct Vent Gas Insert | 9
| 9
installation
MINIMUM FIREPLACE
OPENING (LOW PROFILE
FACEPLATE AND SPACER)
The minimum replace opening for the Regency gas
replace insert is shown in the following diagrams:
MINIMUM FIREPLACE
OPENING
The minimum replace opening for the Regency
gas replace insert when using the supplied spacer
is shown in the following diagrams:
18"
(457mm)
35-1/4" (895mm)
7-1/8”
(200mm)
Low prole
9-1/4"
(235mm)
25-1/2" (648mm)
18" (457mm)
GAS INSERT
AERATION SYSTEM
The air shutter can be adjusted by moving the
adjusting wire up or down. The wire is accessed
through the bottom louver opening. Open the air
shutter for a blue ame or close for a yellower
ame. The burner aeration is factory set but may
need adjusting due to either the local gas supply
or altitude.
Minimum Air Shutter Opening:
5/16" Natural Gas
7/16" Propane
CAUTION: Carbon will be produced if air
shutter is closed too much.
Note: Any damage due to carboning resulting
from improperly setting the aeration
controls is NOT covered under warranty.
Note: Aeration Adjustment should only be
performed by an authorized Regency
Installer at the time of installation.

10 | E33-10 FPI Direct Vent Gas Insert
|
10 installation
MINIMUM CLEARANCES TO COMBUSTIBLES
From Unit
Side Walls * A 8" (203 mm)
Ceiling B 47" (1194 mm)
Min. Mantel Height C 15" (381 mm)
Max. Mantel Depth D 12" (305 mm)
Alcove Width E 76" (1930 mm)
Alcove Depth F 36" (914 mm)
Hearth Height G 1-1/4" (32 mm)
Hearth Width H 45-1/2" (1156 mm)
Hearth Depth I 13" (330 mm)
* Alcove side wall must have a min. of 8"
clearance on one side.
COMBUSTIBLE MANTEL CLEARANCES
Because of the extreme heat this replace emits, the mantel clear-
ances are critical.
Note: A non-combustible mantel may be installed at a lower height
if the framing is made of metal studs covered with a non-
combustible board.
Mantel can be installed anywhere in shaded area or higher using the
above scale.
Note: Ensure the paint that is used on the mantel and the facing is
"heat resistant" or the paint may discolour.