Regency Fireplace Products P36D-NG10 User manual

P36D-10 Gas Fireplace
Model P36D-NG10 P36D-LP10
Fuel Type Natural Gas Propane
Minimum
Supply
Pressure
5” W.C.
(1.25 kPa)
12” W.C.
(3.00 kPa)
Manifold
Pressure - High
3.8” W.C.
(0.95 kPa)
11” W.C.
(2.74 kPa)
Manifold
Pressure - Low
1.1” W.C.
(0.27 kPa)
2.9” W.C.
(0.72 kPa)
Orice Size #37 DMS #52 DMS
Minimum Input 15,500 BTU/h (4.54 kW) 15,000 BTU/h (3.96 kW)
Maximum Input 30,000 BTU/h (8.79 kW) 30,000 BTU/h (8.79 kW)
Vent Sizing 4” Inner / 6 5/8” Outer 4” Inner / 6 5/8” Outer
***Important: Framing height requires consideration of the hearth
depth. Dimension H = H + the thickness of installed hearth.
Approved Venting Systems
Flex Vent Systems: FPI AstroCap™ Flex Vent
Rigid Pipe Vent Systems: Simpson Direct Vent Pro®
American Metal Products® Amerivent Direct
Security Secure Vent®
Selkirk Direct-Temp™
Metal-Fab® Sure Seal
ICC Excel Direct
Regency®P36D-10 Zero Clearance Direct Vent Gas Fireplace | 7
| 7
installation
UNIT DIMENSIONS WITH VIGNETTE FACEPLATE
7
3
16
33-1/16”
34-3/16”
28-15/16”
(735mm)
2mm)
(51mm)
(838mm)
(914mm)
(868mm)
Optional 3 sided finishing trim (not shown) 38" W x 33-3/4" H
Unit Dimensions With Vignette
Faceplate
Gas Fireplaces

P36D-10 Gas Fireplace
UNIT DIMENSIONS WITH VIGNETTE AND VIGNETTE FINISHING TRIM
UNIT DIMENSIONS WITH SAFETY SCREEN (#515-929) AND OPTIONAL LOUVERS
Gas Fireplaces

Non-combustible
Material
J-styleTrim
or metal corner bead
may be used to nish these
edges
Combustible
Material
Combustible
Material
Diagram 2
IMPORTANT FINISHING DETAIL NOTE:
Before placing unit into nal position - it is important to know the
total thickness / height of nished hearth (tile, carpet, etc.) The
base of the replace should be level or higher than the nished
hearth height.
Diagram 3 Shown with optional nishing trim
Note: All non-combustible and combustible facing material
should butt up cleanly to the anges around the rebox
opening.
Rough edges will be visible from the front view with the
Vignette faceplate - if not using the optional nishing trim.
To maintain a clean nished edge - it is recommended to install
the combustible facing material with the nished edge against
the replace / nailing strips.
Alternatively, you can use J Style Trim or Metal Corner Bead
to cover cut edges of the non-combustible facing material.
38
"
33 3
4
"
Diagram 1
P36D-10 Gas Fireplace
Min. 6"
(152mm)
30-1/2" (775mm)
Top of Unit
Min. 32" (1016mm)
to Ceiling"
CLEARANCES
MANTEL LEG CLEARANCES
Combustible mantel leg clearances as per diagram:
Maximum 1-1/2" projection at 2" minimum clearance.
Gas Fireplaces

FINISHING
Diagram 3 Shown with optional nishing trim
P36D-10 Gas Fireplace
COMBUSTIBLE MANTEL CLEARANCES
Because of the extreme heat this replace emits, the mantel clearances are critical.
Combustible mantel clearances from top of unit are shown in the diagram below.
Note: Mantel starts at *1" deep and ends at *12" deep. **For Vignette with Vignette Finishing Trim ush nish, all materials (framing & nishing)
below the mantel and the width of the Vignette nishing trim, (37 1/2") must be non-combustible if a lower mantel is desired.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.
MANTEL CLEARANCES WITH VIGNETTE +
VIGNETTE FINISHING TRIM STEPPED FIN-
ISH
MANTEL CLEARANCES WITH
VIGNETTE + VIGNETTE FINISHING TRIM
FLUSH FINISH
MANTEL CLEARANCES WITH
SAFETY SCREEN AND LOUVERS
Vignette nishing
trim stepped nish.
Finished material
ush to appliance
Vignette nishing
trim, ush nish.
Finished material
ush to Vignette
nishing trim.
MANTEL CLEARANCES WITH
VIGNETTE ONLY (No Vignette Finishing Trim)
No Vignette nishing
trim. Finished ush to the
appliance
Gas Fireplaces

P36D-10 Gas Fireplace
Install Side Nailing Strips, Top Facing
Support, and Top Stando󰀨s before unit
is slipped into position. See the "Unit
Assembly Prior to Installation" section for
assembly details.
1) Determine the total thickness of facing material (e.g. non combustible plus ceramic tiles) to allow the nished surface to be ush with the front of the unit.
Total facing thickness can vary from 1/2" (13mm) to 1-1/4" (32mm) thick with Vignette only, Vignette + Vignette Finishing Trim Stepped Finish and Safety
Screen and Louvers. When installing the Vignette + Vignette Finishing Trim Flush Finish the facing thickness is up to 3".
2) Add a second steel stud at midpoint for ease of installation/securing the non combustible board. See Diagrams 1 & 2.
FRAMING
3) For exterior walls, insulate the enclosure to
the same degree as the rest of the house,
apply vapour barrier and drywall, as per
local installation codes. (Do not insulate the
replace itself.)
4) The top of the unit must not be closer than 32"
(813mm) to the ceiling.
3 - /8"1 3
(82 mm)2
37-7/16"
(951mm)
Non-combustible
Material (supplied)
Steel stud on edge
2nd Steel stud on edge
(install after unit in place)
12"
(305mm)
Wood stud
Wood stud
Drywall
Diagram 1 Diagram 2
Diagram 4 Diagram 5
Vignette + Vignette Finishing Trim Flush Finished
Vignette + Vignette Finishing Trim Stepped Finish or
Vignette Only
NOTE: If using ush louvers and safety screen the steel studs and non-combustible material are not required. Wood studs and drywall
may be used. See framing and nishing for details.
Non-combustible
Note: Secure the non-combustible board (supplied)
directly above the unit as shown. Install a steel
stud directly above the unit as shown to secure the
non-combustible material.
Shown with Vignette Faceplate
Only. No Vignette Finishing Trim
Shown with Vingette and
Vignette Finishing Trim,
Flush Finished
Gas Fireplaces

P36D-10 Gas Fireplace
Frame in the enclosure for the unit with framing
material. The framed opening is 40-3/4" high
x 36-1/4" wide x 17-3/8" deep (1036mm high
x 921mm wide x 441mm deep).
Frame in the enclosure for the unit with framing
material. The framed opening is 41-5/8" high x
38" wide x 17-3/8" deep (1057mm high x 965mm
wide x 441mm deep).
All other framing may be of combustible
materials, i.e. 2 x 4, 2 x 6
All other framing may be of combustible
materials, i.e. 2 x 4, 2 x 6
Vignette Framing Dimensions
ABCD
36-1/4" 40-3/4" 17-3/8" 46"*
921mm 1036mm 441mm 1168mm*
* 'D' is Minimum height to combustible materials
including the Minimum 2" (51mm) Top clearance
to the Horizontal Vent.
Vignette + Finishing Trim - Flush Finish
Framing Dimensions
ABCD
38" 41-5/8" 19-3/8" 46"*
965mm 1057mm 492mm 1168mm*
* 'D' is Minimum height to combustible materials
including the Minimum 2" (51mm) Top clearance
to the Horizontal Vent.
Safety Screen + Louvers
Framing Dimensions
ABCD
36-1/4" 37-1/4" 17-3/8" 46"*
921mm 946mm 441mm 1168mm*
* 'D' is Minimum height to combustible materials
including the Minimum 2" (51mm) Top clearance
to the Horizontal Vent.
Diagram 1 Diagram 3 Diagram 5
Diagram 6
Diagram 2 Diagram 4
B
Steel stud on edge
A
C
D
*Minimum Height
to Combustible
Material
B
Wood stud on edge
A
C
D
*Minimum Height
to Combustible
Material
B
Steel stud on edge
A
C
D
*Minimum Height
to Combustible
Material
Frame in the enclosure for the unit with framing
material. The framed opening is 37-1/4" high x
36-1/4" wide x 17-3/8" deep (946mm high x
921mm wide x 441mm deep).
FRAMING WITH
VIGNETTE FACEPLATE/VIGNETTE
FINISHING TRIM, STEPPED FINISH
FRAMING WITH VIGNETTE
FACEPLATE & VIGNETTE FINISHING
TRIM FINISHED FLUSH
FRAMING WITH
LOUVERS AND SAFETY SCREEN
Wood stud on
edge
NOTE: If using the optional Vignette nishing trim, this can be installed as a 3-sided or 4 sided nish trim. If choosing to use
this as a 4 sided nish trim the framing would need to be increased by 1-1/4" inches minimum in order for this to t. This
must be to the nished oor. (Eg: Diagram 2 B= 40-3/4" framing height + 1-1/4". Bottom of 4-sided nishing trim +1/2 thick
nished oor = 42-1/2".
Gas Fireplaces

P36D-10 Gas Fireplace
VENTING
DIRECT VENT SYSTEM (FLEX)
HORIZONTAL TERMINATIONS ONLY
These venting systems, in combination with the P36D-10 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system
by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in the "Exterior
Vent Termination Locations" section.
Regency Direct Vent (Flex) System Termination Kit (Part # 946-515) includes all the parts needed to install the P36D-10 with a maximum
run of 4 feet.
1) 6-7/8" dia. exible liner (4 ft. length)
2) 4" dia. exible liner (4 ft. length)
3) spring spacers (4)
4) thimble (2)
5) AstroCap termination cap (1)
6) screws (12)
7) tube of Mill Pac (1)
8) plated screws (8)
9) screws #8 x 1-1/2" Drill Point, Stainless
Steel (4)
1) 6-7/8" dia. exible liner (10 ft. length)
2) 4" dia. exible liner (10 ft. length)
3) spring spacers (7)
4) thimble (2)
5) AstroCap termination cap (1)
6) screws (12)
7) tube of Mill Pac (1)
8) plated screws (8)
9) screws #8 x 1-1/2" Drill Point, Stainless
Steel (4)
If longer runs are needed, the Regency Direct
Vent system (Flex) # 946-516 includes all
the parts needed to install the P36D with a
maximum 10' run.
Notes:
1) Liner sections should be continuous without any joints or seams.
2) Only Flex pipe purchased from Regency may be used for Flex installations.
Gas Fireplaces

P36D-10 Gas Fireplace
Rigid Pipe Adaptor
Pipe Length
Vertical
Termination
Cap
Storm Collar
Flashing
Ceiling Firestop
24" Pipe
Length
Adj.Pipe Length
11"-14-5/8"
90 Elbow
o
Horizontal
Termination
Cap
Wall Thimble
Vinyl Siding
Standoff (Optional)
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
The minimum components required for a basic horizontal termination are:
1 Horizontal Termination Cap
1 90o Elbow
1 Rigid Pipe Adaptor
1 Wall Thimble
1 Length of pipe to suit wall thickness (see chart)
Wall thickness is measured from the back stando󰀨s to the inside mounting
surface of termination cap. For siding other than vinyl furring strips may be
used, instead of the vinyl siding stando󰀨, to create a level surface to mount the
vent terminal. The Terminal must not be recessed into siding. Measure the wall
thickness including furring strips.
If a Vinyl Siding Stando󰀨 is required (it must be used with vinyl siding), measure
to outside surface of wall without siding and add 2 inches.
Alternate
Horizontal Termination
Caps
Flat Wall Installation
Wall Thickness
(inches)
Vent Length Required
(inches)
4" - 5-1/2" 6"
7" - 8-1/2" 9"
10" - 11-1/2" 12"
9" - 14-1/2" 11" - 14-5/8" Adj. Pipe
15" - 23-1/2" 17" - 24" Adj.
Corner Installation
Wall Thickness
(inches)
Vent Length Required
(inches)
3-1/4" - 6-3/4" 11" - 14-5/8" Adj. Pipe
7-3/4" - 16-1/4" 17" - 24" Adj. Pipe
7-1/4" - 8-3/4" 6" + 12"
9" + 9"
4-1/4" - 5-3/4" 6" + 9"
This product has been evaluated by Intertek
for using a Rigid Pipe Adaptor in conjunction
with Duravent Direct-Vent , Selkirk Direct-Temp,
Ameri Vent Direct venting and Security Secure
Vent systems. Use of these systems with the
Rigid Pipe adaptor is deemed acceptable
and does not a󰀨ect the Intertek WHI listing of
components.
WARNING:
Do not combine venting components from
di󰀨erent venting systems.
However use of the AstroCapTM and
Regency Riser is acceptable with all systems.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The Regency AstroCapTM and Regency Riser Vent terminal are certied for installations using Regency venting systems as well as Simpson
Dura-Vent® Direct Vent , American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, Selkirk Direct-Temp. AstroCapTM is a proprietary
trademark of Regency Fireplace Products. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
Gas Fireplaces

P36D Gas Fireplace
• Vent must be supported at o󰀨sets.
• Firestops are required at each oor level and whenever
passing through a wall.
• Maintain clearances to combustibles.
Note: Must use optional rigid pipe adaptor when using
rigid vent systems (Part # 510-994).
RIGID PIPE VENTING ARRANGEMENTS
VERTICAL TERMINATIONS
(Propane & Natural Gas)
The shaded area in the diagram shows all allowable combinations of straight vertical and o󰀨set to vertical terminations, using two 90o elbow, with Rigid
Pipe vent systems for Propane and Natural Gas.
Gas Fireplaces

P36D Gas Fireplace
5HJHQF\3'=HUR&OHDUDQFH'LUHFW9HQW*DV)LUHSODFH | 25
| 25
installation
7KH 3' LV DSSURYHG IRU D  IW VWUDLJKW
YHUWLFDOZLWKULJLGSLSHYHQWV\VWHPVIRU3URSDQH
DQG1DWXUDO*DVDVSHUWKHGLDJUDP
7KH VKDGHG DUHD LQ WKH GLDJUDPVKRZV DOO
DOORZDEOH FRPELQDWLRQVRI VWUDLJKWYHUWLFDO DQG
RIIVHWWRYHUWLFDOWHUPLQDWLRQVZLWKULJLGSLSHYHQW
V\VWHPVIRU3URSDQHDQG1DWXUDO*DV0D[LPXP
WZRRHOERZVDOORZHG
9HQWPXVWEHVXSSRUWHGDWRIIVHWV
 )LUHVWRSV DUH UHTXLUHG DW HDFK ÀRRU OHYHO
DQGZKHQHYHUSDVVLQJWKURXJKDZDOO
0DLQWDLQFOHDUDQFHVWRFRPEXVWLEOHV
'LDJUDP
Gas Fireplaces

$OO5LJLG3LSH6\VWHPV
LQQHUGLDPHWHU
RXWHUGLDPHWHU
)3,)OH[9HQW
LQQHUGLDPHWHU
LQQHUGLDPHWHU
0DLQWDLQFOHDUDQFHVWRFRPEXVWLEOHV
+RUL]RQWDOYHQWPXVWEHVXSSRUWHGHYHU\IHHW
)LUHVWRSVDUHUHTXLUHGDWHDFKÀRRUOHYHODQGZKHQHYHUSDVVLQJWKURXJKDZDOO
$ YHQW JXDUG VKRXOG EH XVHG
ZKHQHYHUWKH WHUPLQDWLRQ LV ORZHU
WKDQ WKH VSHFL¿HG PLQLPXP RU DV
SHUORFDOFRGHV
1RWH )3,'LUHFW9HQW)OH[6\VWHP3DUW
V
DQGDUHRQO\
DSSURYHG
IRUKRUL]RQWDOWHUPLQDWLRQV
RIGID PIPE VENTING ARRANGEMENTS
HORIZONTAL TERMINATIONS
Regency DIRECT VENT SYSTEM (FLEX) (Propane & Natural Gas)
The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o elbow (two 45o elbows equal one 90o elbow).
Note: Must use optional rigid pipe adaptor (Part # 510-994) when using Rigid Pipe venting systems.
P36D Gas Fireplace
Gas Fireplaces

Vertical Termination with Co-Linear Flex System
The appliance must not be connected to a chimney ue
serving a separate solid fuel burning appliance.
Masonry chimneys may take various contours which the exible liner
will accommodate. However, keep the exible liner as straight as
possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the
termination cap.
This appliance is designed to be attached to two 3” (76mm) co-linear
aluminium ex running the full length of the chimney. See the Venting
Arrangements for minimum and maximum heights.
Required Parts:
Part # Description
946-529 Co-linear DV Vertical Termination Cap
948-305 3” Flex - 35 ft.
946-563 Coaxial to Co-linear Adapter Kit which contains
the following: Co-linear Flex Adapter Outer Pipe
Inner Pipe Adapter
510-994 Flue Adapter
46dva-E45 45º Elbow
Alternate Approved Caps
46dva-VC Vertical Termination Cap
46dva-VCH High Wind Cap
46dva-GK 3” Co-linear Adapter with ashing
The shaded area in the diagrams
show the allowable vertical
terminations.
Please refer to Exterior
Vent Terminations for
additional guidelines on
vent locations.
Flex Liner
Exhaust
Flue
A maximum
of two certified
joiner kits
may be used
per length.
#948-305 (35 ft)
Air Intake
Co-linear DV
Vertical Termination
Cap#946-529
Co-Linear
Flex
Adapter
with Kit#
946-563
Outer
Pipe
with Kit#
946-563
Inner Pipe
Adapter
with Kit#
946-563
Rigid Pipe Adapter
# 510-994 90 Degree
Elbow
Pipe Length
8' Min.
40-1/2
30' Max.
30
Horizontal Distance (Feet)
Vertical Height (feet)
2 max.
P36D Gas Fireplace
Gas Fireplaces