Regent Lighting Solutions Giza User manual

1
2
www.regentlight.co.za
www.regentlight.co.za
INSTALLATION INSTRUCTIONS
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
1
2
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
Regent Lighting reserves the right to change specifications modify designs and discontinue items without
incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other
information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be
liable for any error therein.
ALL LUMINAIRES SUPPLIED AND TO BE INSTALLED ABOVE AND BELOW 5 METERS ARE IN COMPLIANCE WITH SANS
60598 SECTION 3.5.6 ACCORDING TO THE MANUFACTURER GUARANTEE AND WARRANTY
WARNING: TO AVOID FIRE, SHOCK OR DEATH
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING
Electrical products can cause death, injury, or damage to property. Installation of
this product must be carried out by a qualified electrician, in compliance with
SANS 10142 or corresponding regulations of the country of installation. On
completion of installation, the Certificate of Compliance must be updated.
Giza
WARNING
Electronic/Magnetic Control Device
Electronic/Magnetic Control Device
WARNING
3 - 13 MAIN REEF SERVICE ROAD, CORNER
SPRINGBOK AND MAIN REEF ROAD, INDUSTRIA,
JOHANNESBURG. SOUTH AFRICA.
TEL : [phone]
www.regentlight.co.za
RE GENT L I GHT ING A D IVIS ION
OF WA HL IND USTR IES.
Save These Instructions for Future Reference
Save These Instructions for Future Reference
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
2. Remove the body from the
base (back plate).
Giza
1. Undo the four allen key fasteners
that hold the base to the body of the
fitting.
Requirements:
ŸBe sure the electricity to the system
you are working on is isolated.
ŸTwo screws/ wall plugs and M6
washers are required for mounting
the wall bracket to the surface
(not supplied).
DO NOT CONNECT THE FITTING LIVE
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
Giza Giza Eyelid Giza Plateau
1
Giza Eyelid: Disassemble Giza
Clamp Ring from the base &
Diffuser. Keep all screws and bolts
Giza Plateau
Giza Giza Eyelid
– For non-user replaceable light sources:
"The light source contained in this luminaire shall only be replaced by the
manufacturer or his/her service agent or a similar qualied person."
May 2020

2x6mm
Mounting
Holes
www.regentlight.co.za
www.regentlight.co.za
3
4
5
7
7
6
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps/LED timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Use only the correct light bulbs/LED as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
Important Safety Instructions
7. After replacing the
main body switch on the
power supply.
4. Use mounting screws to
f as t en t he b a se t o t h e
mounting surface.
Ensure that the mounting
screws are equipped with a
rubber washer to prevent
water from enter ing the
luminaire.
3 . S e l e c t t h e r e q u i r e d
position for the luminaire.
The diagram on the right
provides measurements of
where the mounting holes
a r e l o c a t e d . U s e t h e
diagram to pinpoint the
positions of the hols onto the
chosen mounting surface
and drill the holes.
Power Supply
Hole
6. Reassemble all components of the luminaire to
the mounted base. Apply pressures to the main
body when assembling the two bodies.
Use the four stainless steel allen key screws to
fasten the main body to the base.
Mounting screw
Rubber washer
Washer
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
Earth Loop
Green/Yellow
Switch
Wire Red
Neutral loop
Black or Blue
Mains to
Luminaire
(L) Brown
(E) Green/Yellow
(N) Blue
EARTH – (Green/Yellow) to
terminal marked.
5. Connect the Switched Live
(S/A), Neutral (N) and Earth
(E) cable(s) to the terminal
block through the cable
gland in the back plate (still
detached from front face).
SWITCHED LIVE – (Red or
Brown) to terminal marked L
NEUTRAL – (Black or Blue) to
terminal marked N
To install or replace the
lamp/ LED, remove the
body of the luminaire, via
the four screw fasteners,
see Step 1 & 2.
Ensure the new lamp/ LED is
t h e c o r r e c t
wattage/Correct colour
lamp by referring to the
specications, and that the
lam p/ L E D i s s ec ur e ly
located in the lamp holder
or the LED bracket.
Reassemble the tting by
using Step 6 & 7.
taking care of any loose
parts which may fall
LIGHTING
REGENT
CFL 26W
220-240V 50Hz
CLASS 1 IP 65
220-240V 50Hz
LED 18W
CLASS 1 IP 65
LIGHTING
REGENT
Giza
Giza Eyelid Giza Plateau
Giza Eyelid: Reassemble Giza
Clamp Ring to original position
6.1