Regent Lighting Solutions Bedford Bollard - Plinth Mounted User manual

Requirements:
Be sure the electricity to the system
you are working on is isolated.
If the main supply power (live) is on, it
will cause damage to the luminaire.
1. Select the required position for the
luminaire, towards the pathway.
A. Ensure the electrical cable is fed through
the mounting hole where the bollard will be
installed.
B. Insert the bolt cage into the mounting
hole and feed the electrical cable through
the bolt cage towards the surface, ensuring
the cable is fed parallel to the pathway.
B
Ground Level
1
2
www.regentlight.co.za
www.regentlight.co.za
INSTALLATION INSTRUCTIONS
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
1
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
Regent Lighting reserves the right to change specifications modify designs and discontinue items without
incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other
information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be
liable for any error therein.
WARNING: TO AVOID FIRE, SHOCK OR DEATH
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING
ALL LUMINAIRES SUPPLIED AND TO BE INSTALLED ABOVE AND BELOW 5 METERS ARE IN COMPLIANCE WITH SANS
60598 SECTION 3.5.6 ACCORDING TO THE MANUFACTURER GUARANTEE AND WARRANTY
Electrical products can cause death, injury, or damage to
property. Installation of this product must be carried out by a
qualified electrician, in compliance with SANS 10142 or
corresponding regulations of the country of installation. On
completion of installation, the Certificate of Compliance must
be updated.
Bedford Bollard - Plinth Mounted
Electronic/Magnetic Control Device
WARNING
Electronic/Magnetic Control Device
WARNING
3 - 13 MAIN REEF SERVICE ROAD, CORNER
SPRINGBOK AND MAIN REEF ROAD, INDUSTRIA,
JOHANNESBURG. SOUTH AFRICA.
TEL : [phone]
www.regentlight.co.za
RE GE NT LIGHTING A DIVISION O F WAHL
IN DU ST RI ES.
DO NOT CONNECT THE FITTING LIVE
December 2017
Save These Instructions for Future Reference
Save These Instructions for Future Reference
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
Bedford Bollard - Plinth Mounted
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
Clear diffuser
with louvre
Bedford Dome
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
Opal diffuser
with louvre
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
Clear diffuser
with louvre
Opal diffuser
with louvre
Bedford Cone
Clear diffuser
with louvre
Opal diffuser
with louvre
Bedford Flat
Ground Level
A
BOLT CAGE ORIENTATION
PATHWAY/LIGHT SOURCE DIRECTION
SERVICE/ACCESS DOOR DIRECTION
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1

5
7
8
4
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps/LED timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Use only the correct light bulbs/LED as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
Important Safety Instructions
MCB
L
E
N
5. S witch on th e power
supply.
www.regentlight.co.za
www.regentlight.co.za
2
3
Access door must
be positioned away
from the pathway
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
Clear diffuser
with louvre
Bedford Dome
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
Opal diffuser
with louvre
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
LIGHT_5
11,1,10-1-1
LIGHT_6
11,1,10-1-1
Clear diffuser
with louvre
Opal diffuser
with louvre
Bedford Cone
Clear diffuser
with louvre
Opal diffuser
with louvre
Bedford Flat
2. Remove the access door. Feed
the cable from the ground
through the glands at the bottom
of the fitting to the access door.
Connect the Switched Live (S/A),
Neutral (N) and Earth (E) cable(s)
to the MCB and connector block
in the access door.
SWITCHED LIVE – (Red or Brown)
to terminal marked L
NEUTRAL – (Black or Blue) to
terminal marked N
EARTH – ( G r e en/Yello w ) to
terminal marked.
On ce compl ete , fas ten the
glands on the gland plate to seal
the glands to maintain the IP
rating.
Mains to
Luminaire
Earth Loop
Green/Yellow
Switch
Wire Red
(L) Brown
(E) Green/Yellow
(N) Blue
Neutral loop
Black or Blue
Connect power supply
into the fitting
3 . E n s u r e t h e g l a n d i s
fastened before fastening
the bollard to the plinth.
Fix the base mounting to the
required position with the
fasteners provided.
Ensure the bollard is aligned
correctly to the base and the
light source is positioned
towards the pathway.
Neatly place the cable joint
into the bolt cage.
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
300mm
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
4. Ensure that there are no
exposed conductors, loose
strands or trapped insulation
and that the fitting is facing
the correct way, towards the
pathway.
Connect the main power
supply to the MCB
Mains to
Luminaire
Earth Loop
Green/Yellow
Switch
Wire Red
(L) Brown
(E) Green/Yellow
(N) Blue
Neutral loop
Black or Blue
Fasten the glands on the gland plate
to seal the glands to maintain the IP rating.