www.regentlight.co.za
3
4
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps/LED timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Use only the correct light bulbs/LED as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
Ensure there is no trapped or pinched
insulation before fastening the wall
plate.
Mount the wall plate to the selected
surface through fastening M6 Stainless
Steel screws with rubber washers into the
wall plugs already inserted into the wall.
Ensure the wall plate is level vertically
and horizontally.
3. After the mounting holes are drilled
place the wall plugs inside the mounting
holes and feed the electrical cable
through the grommet on the wall plate.
5
6
MOUNTING THE FITTING ASSEMBLING
ELECTRICAL CONNECTION
x4 M6 Screws
Power Cable
Grommet
Wall Plugs
Mounting Surface
Connector Block
Gaskets
Gaskets
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
6. T o in st al l or ch an ge t h e l a m p / L E D ,
re mo v e/ re pl a c e t he e nd c ap s on th e
top/bottom of the fitting, taking care of any
loose parts which may fall.
Ensure the gaskets and grommet is securely in
place before fastening the end caps and the
wall box.
Ensure the new lamp/LED is the correct wattage
and is located in the lamp/LED holder.
Ensure that there are no exposed conductors,
loose strands or trapped insulation.
Ensure the fitting is securely fastened to the wall plat.
5. Place the connector block inside the wall box and
align and fasten the fitting to the wall plate via the
four stainless steel grub screws which were removed
in the first step.
To protect the ingress protection, ensure the
mounting plate gasket is securely in place before
fixing the fitting to the mounting plate.
Ensure that there are no exposed conductors, loose
strands or trapped insulation.
E A R T H – ( G r e e n / Y e l l o w ) t o
terminal marked E.
SWITCHED LIVE – (Red or Brown) to
terminal marked L
NEUTRAL – (Black or Blue) to
terminal marked N
4. Connect the Switched Live (S/L),
Neutral (N) and Earth (E) cable(s)
to the connector block in the wall
box of the fitting.
Replaceable
electrical
components
by end user
Replaceable
electrical
components
by end user
Luminaire
-Red/Brown (+)
-Green/Yellow
-Black/Blue (-)
Main electrical supply
Red/Brown-
Green/Yellow-
Black/Blue-
220 ~ 240V AC 50 Hz
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
Replaceable
electrical
components
by end user
Replaceable
electrical
components
by end user
Important Safety Instructions Important Safety Instructions
7
www.regentlight.co.za
This product is available as
a single or double element.
This installation manual is
applicable for both.
7. Switch on power supply.
Replaceable
electrical
components
by end user
Single
Double
Allen Key
x4 M5 cap screws
x4 M5 cap screws
x4 M4 Grub
screws
