Regent Lighting Solutions Plato User manual

ŸIf the main supply power (live) is
on, it will cause damage to the
luminaire.
Feed the electrical cable (main
supply) through the installed bolt
cage.
1. Select required position for the
bollard. Ensure the mounting hole has
an electrical cable.
ŸBe sure the electricity to the
system you are working on is
isolated.
Requirements:
Ensure the tting is installed in the
correct direction to the pathway.
Install bolt cage/stubby at desired
height and ensure that it is square as
it cannot be adjusted later. Ensure
the bolt cage is level.
Electronic Control Device
WARNING
Electronic Control Device
WARNING
1
Plato Bollard
Plinth Mounted
www.regentlight.co.za
1
Save These Instructions for Future Reference
Save These Instructions for Future Reference
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
DO NOT CONNECT THE FITTING LIVE
April 2021 Stubby
Ground Level
A
Side view of installed
stubby
Level
Level
INSTALLATION INSTRUCTIONS
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
www.regentlight.co.za
Regent Lighting reserves the right to change specifications modify designs and discontinue items without
incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other
information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be
liable for any error therein.
WARNING: TO AVOID FIRE, SHOCK OR DEATH
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING
ALL LUMINAIRES SUPPLIED AND TO BE INSTALLED ABOVE AND BELOW 5 METERS ARE IN COMPLIANCE WITH SANS
60598 SECTION 3.5.6 ACCORDING TO THE MANUFACTURER GUARANTEE AND WARRANTY
Electrical products can cause death, injury, or damage to property.
Installation of this product must be carried out by a qualified electrician, in
compliance with SANS 10142 or corresponding regulations of the country
of installation. On completion of installation, the Certificate of Compliance
must be updated.
3 - 13 MAIN REEF SERVICE ROAD, CORNER
SPRINGBOK AND MAIN REEF ROAD, INDUSTRIA,
JOHANNESBURG. SOUTH AFRICA.
TEL : [phone]
www.regentlight.co.za
RE GENT L I GHT ING A D IVIS ION OF WAH L
IN DUST RIES.
Plato Bollard
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
770mm
For non user replaceable light source: The light source contained in this luminaire
shall only be replacedby the manufacturer or his/her service
agent or a similar qualied person
500mm
Plinth Mounted

www.regentlight.co.za
www.regentlight.co.za
1A
Use only the correct light bulbs as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
500mm with Access Door
1.
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Important Safety Instructions
Ensure the bollard is aligned
correctly to the base and the
light source is positioned
towards the pathway.
Neatly feed the cable up to
the access door for
connection.
2. En sur e b olt cag e i s
installed and Cable is fed
through the bold cage.
Fix the bollard to the required
position with the fasteners
provided onto the bolt cage.
Ground Level
B
300
200
Plato Bollard
500mm
Bolt Cage
PATHWAY
NEUTRAL – (Black or Blue) to
terminal marked N
C. Replace the access door
and fasten the access door
with stainless steel fasteners.
SWITCHED Live – (Red or
Brown) to terminal marked L
EARTH – (Green/Yellow) to
terminal marked.
B. Connect the cable from
the fitting. Connect the
Switched Live (S/A), Neutral
(N) and Earth (E) cable(s) to
t h e c o n n e c t o r b l o c k
(supplied).
2B-2 A. Remove the access
door via the stainless steel
fasteners.
Mains to
Luminaire
Earth Loop
Green/Yellow
Switch
Wire Red
(L) Brown
(E) Green/Yellow
(N) Blue
Neutral loop
Black or Blue
Remove access door.
Replace access door.
A
C
Connect power
to the tting.
To Luminaire
Mains power
B
L N
2B
2.
3. Switch on the power
supply.
3.
Fasten the bollard to the
bolt cage using the stainless
steel m10 nuts .
3. Ens ure th e b olla rd is
aligned correctly to the base
an d the l ig ht so ur ce is
po s it io ne d t ow ar ds t he
pathway.

www.regentlight.co.za
www.regentlight.co.za
2A
Use only the correct light bulbs as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
SWITCHED Live – (Red or
Brown) to terminal marked L
2. F ix Ge ar Tray t o th e
required position with the
fasteners provided in the
Stubby.
Connect the cable to the
connector block. Connect
the Switched Live (S/A),
Neutral (N) and Earth (E)
cable(s) to the cable joining
kit (supplied).
NEUTRAL – (Black or Blue) to
terminal marked N
EARTH – (Green/Yellow) to
terminal marked.
Fasten from
in the stubby
To LED
Power Supply
Mains to
Luminaire
Earth Loop
Green/Yellow
Switch
Wire Red
(L) Brown
(E) Green/Yellow
(N) Blue
Neutral loop
Black or Blue
700mm No Access Door
Male/Female
connectors
Male/Female
connectors
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Important Safety Instructions
Allen Key
Hex Cap Screw
3. Connect the Male/Female
connectors to the fitting.
Once connected. Fix the
Plato bollard to the bolt
c a g e s t u b b y w i t h t h e
fasteners provided
or trapped insulation.
Ensure the bollard is aligned
correctly to the base and the
light source is positioned
towards the pathway.
Ensure there is no pinched
Fasten the bollard to the
bolt cage using the stainless
steel fasteners with an allen
key.
4. Ens ure th e b olla rd is
aligned correctly to the base
an d the l ig ht so ur ce is
po s it io ne d t ow ar ds t he
pathway.
5. Switch on the power
supply.
2B
2.
1.
3.

www.regentlight.co.za
www.regentlight.co.za
2B
Use only the correct light bulbs as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
700mm with Access Door
1.
2.
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Important Safety Instructions
Allen Key
Hex Cap Screw
2. Fix the bollard to the
required position with the
fasteners provided onto the
bolt cage.
Ensure the bollard is aligned
correctly to the base and the
light source is positioned
towards the pathway.
Neatly feed the cable up to
the access door for
connection.
3. Ens ure th e b ollar d i s
aligned correctly to the base
an d the l ig ht so ur ce is
po s it io ne d t ow ar ds t he
pathway.
Fasten the bollard to the
bolt cage using the stainless
steel fasteners with an allen
key.
3
3.
3. Switch on the power
supply.
Replace the access door
and fasten the access door
with stainless steel fasteners.
4. Remove the access door
v i a t h e s t a i n l e s s s t e e l
fasteners.
Connect the Switched Live
(S/A), Neutral (N) and Earth
(E) cable(s) to the cable
joining kit (supplied).
SWITCHED Live – (Red or
Brown) to terminal marked L
NEUTRAL – (Black or Blue) to
terminal marked N
EARTH – (Green/Yellow) to
terminal marked.
Mains to
Luminaire
Earth Loop
Green/Yellow
Switch
Wire Red
(L) Brown
(E) Green/Yellow
(N) Blue
Neutral loop
Black or Blue
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.