Regent Lighting Solutions Columbia User manual

1
2
www.regentlight.co.za
www.regentlight.co.za
INSTALLATION INSTRUCTIONS
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
1
2
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
Regent Lighting reserves the right to change specifications modify designs and discontinue items without
incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other
information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be
liable for any error therein.
WARNING: TO AVOID FIRE, SHOCK OR DEATH
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING
ALL LUMINAIRES SUPPLIED AND TO BE INSTALLED ABOVE AND BELOW 5 METERS ARE IN COMPLIANCE WITH SANS
60598 SECTION 3.5.6 ACCORDING TO THE MANUFACTURER GUARANTEE AND WARRANTY
Electrical products can cause death, injury, or damage to
property. Installation of this product must be carried out by a
qualified electrician, in compliance with SANS 10142 or
corresponding regulations of the country of installation. On
completion of installation, the Certificate of Compliance must
be updated.
Columbia
Magnetic/Electronic Control Device
WARNING
Magnetic/Electronic Control Device
WARNING
3 - 13 MAIN REEF SERVICE ROAD, CORNER
SPRINGBOK AND MAIN REEF ROAD, INDUSTRIA,
JOHANNESBURG. SOUTH AFRICA.
TEL : [phone]
www.regentlight.co.za
RE GENT L I GHT ING A D IVIS ION OF WAH L
IN DUST RIES.
November 2017
Mains to
Luminaire
Earth Loop
Green/Yellow
Switch
Wire Red
Neutral loop
Black or Blue
(L) Brown
(E) Green/Yellow
(N) Blue
Save These Instructions for Future Reference
DO NOT CONNECT THE FITTING LIVE
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
2. Connect the cables fed
through the cable gland at
the bottom of the spigot to
the IP rated connector
block.
SWITCHED LIVE – (Red or
Brown) to terminal marked L
NEUTRAL – (Black or Blue) to
terminal marked N
EARTH – (Green/Yellow) to
terminal marked.
Requirements:
Be sure the electricity to
the system you are
working on is isolated.
x1 IP rated connector
box.
1. Ensure the pole is
installed correctly and has
a diameter of Ø76mm.
Columbia
THIS WAY UP
Pole
Recommended mounting height: 3.5m to 6m*
Wall mount
bracket
51mm O
76mm O
76.0
Cable
gland
Connection
point
Light source

www.regentlight.co.za
www.regentlight.co.za
3
4
5
7
8
6
7
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps/LED timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Use only the correct light bulbs/LED as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
Important Safety Instructions
Light source
5. To install or change the
lamp/LED, unscrew the two
countersunk stainless steel
screws on the top of the lid
and remove the lid from the
main body, taking care of
any loose parts which may
fall.
Ensure the new lamp/LED is
t h e c o r r e c t w a t t a g e ,
a c c o r d i n g t o t h e
specification and is securely
located in the lamp holder
or mounting surface.
7. Switch on the power
supply.
6. Replace the lid and
secure the lid to the body.
Ensure the gasket is securely
in place before fastening
the lid to the body.
4. Ensure that there are no
exposed conductors, loose
strands or trapped/pinched
insulation between the pole
and the spigot.
3. Place the spigot of the
post top on the pole, and
tighten the three M8 stainless
steel grub screws (supplied),
using an allen key to the
pole.
Ensure the fitting is securely
fastened to the pole.
M8 Grub screw
REGENT
LIGHTING
CFL/HPS/MH/W
E27/G24
230V 50Hz
C129 Columbia
CLASS 1 IP 65
LOT 00000
REGENT
LIGHTING
LED/W/K
230V 50Hz
C129 Columbia
CLASS 1 IP 65
LOT 00000
Light source